Quick Start Guide

ManualsBrands2GIG ManualsElectronicsEdge Panel (Bluetooth, WiFi, LTE, Z-wave and SUB GHz transmitters)

Table Of Contents

Standard-Style Duplex Receptacle

Decora-Style Duplex Receptacle

8. Install Retaining Wall Bracket and Connect the AC Power Supply

For compliance with ANSI/NFPA 70: National Electric Code in the United States, you must

install the power supply retaining bracket (not required in Canada).

2GIG

Security & Smart Home System

2GIG EDGE Installer Quick Start Guide

10029907 Rev-X2 | 2GIG-EDG-NA | Edge Panel

Barrel

Connector

Back Plate

Attached to Wall

DC Out +

DC Out –

GRD

Bell +

Bell –

Zone 1

Zone 2

GRD

DC IN

DC IN +

DC IN –

OCL 1

OCL 2

5. Connect Power (Barrel Connector)

The Barrel connector is an alternate method for connecting the AC power supply for

the EDGE Panel.

WARNING!! Do NOT plug the power supply into the outlet at this time.

4. Connect the Power Wires (Terminal Block)

Locate a wall outlet for the plug-in power supply, but do NOT connect the power

supply to the outlet at this time.

IMPORTANT: Never connect the plug-in power supply to a switch-controlled outlet. Do not over-

tighten the terminal block’s contact screws.

STANDARD

DECORA

STANDARD

DECORA

Standard Style – Center Fastener Decora Style – Center Fastener

Secure with Fastener

7. Hang the EDGE Panel

Place the backplate over the lower lip on the back of the chassis, and ip the EDGE

panel upward and push until it clicks into place.

Battery Power Terminal

PRINTER’S INSTRUCTIONS:

INSTALLER QUICK START GUIDE,2GIG-EDG-NA: P/N 10029907 Rev-X2, INK: BLACK, 20LB. MEAD BOND, TOL. +/- 0.125", SCALE: 1:1, FRONT & BACK,11"x17" PAGES: 2, FOLDING: FINISH SIZE - 8.5”x5.5” , BINDING: NONE, (PAGE 1 OF 4)

IntroductIon

This quick start guide introduces 2GIG alarm dealers and professional installers to

2GIG EDGE panel hardware installation and the Installer Toolbox. It describes the

process of program zones, keyfobs, and keypads for the EDGE Panel and how to

add and remove Z-Wave

devices from the network. To get started, navigate to the

Installer Toolbox menu.

EdgE PanEl InstallatIon

Choose the Location for the 2GIG EDGE Panel’s Backplate

Before mounting the backplate, choose a location. Work with the end user to

determine the best location. Always choose an indoor location protected from

temperature extremes.

Recommended Tools and Equipment

To install the system, these tools and equipment are recommended:

â 2-Conductor Power Wire (if connecting power supply to the panel’s terminal block)

â Drywall Saw (or equivalent)

â Ladder

â Magnetic Phillips Head Screwdriver

â Screwdrivers

â Staple Gun

â Wire Stripper

Choose the Wall Location

To choose a wall location:

â Always choose a location that is above ground and centrally located. Do NOT install

the Panel below ground level, because wireless range may be impaired.

â Do NOT connect the Panel to a light switch-controlled outlet.

â Avoid choosing a location that can be easily viewed from doors or windows.

â Avoid choosing a location that is within reach of small children.

â Avoid choosing a location in direct sunlight.

NOTE: If necessary, the Panel can be mounted on a stand that can be placed on a at

surface, such as desk or counter using the 2GIG Desktop Kit. However, this option

may affect compliance with state or regional codes. For 2GIG Desktop Kit installation

instructions, refer to the 2GIG EDGE Installation Manual.

External Attic Mount Antenna Installation (Optional)

If you will be installing the optional External Attic Mount Antenna, refer to the 2GIG

EDGE Installation Guide.

1. Align Backplate to Mark Hole Locations

Create mounting holes, and cut a slot in the dry wall for the AC power cord and other

electrical wiring (if needed).

2. Mount the Backplate to a Wall

Use the four (4) wall anchors and screws (supplied).

NOTE: The Wall Anchor is the wall tamper and MUST be anchored to work.

LEVEL NOT LEVEL

Wall Tamper

Illustration displays both types of power connection:

Install the 2 - conductor power wires or Barrel Connector

3. Hang the Panel for Wiring (optional)

Attach the panel’s third-hand hanging strap to the hook at the bottom of the backplate

for easy access during wiring.

Edge Panel (upside down)

Back Plate

Hanger

6. Connect the Backup Battery

Align pins, then carefully insert the battery cable.

Indicates Mounting Hole