Owner's manual

ManualsBrands2GIG ManualsFor HomeDW10-345 Thin DW Contact

INSTALL INSTRUCTIONS

The2GIG‐DW10‐345isaThinDoor/WindowContactthatcanbeinstalledondoors,windows,andmanyotherobjectsthatopenandclose.

ThesensortransmitssignalstotheControlPanelwhenamagnetmountednearthesensorismovedawayfromorclosertothesensor.The

sensorhasanex

ternalinputthatacceptsN/Cdrycontactdevices.Thesensorisalsoequippedwithacovertamperforadditionalsecurity.

Box Contents

•D/WSensor

•Magnet

•2Screws

•3MTape

•12”WireLead

Programming

Thefollowingstepsareforprogramming(learning)thesensor(2GIG‐DW10‐345)intothe2GIG

ControlPanel.Scrollbetweenoponsusingthe←and→arrows.Movetothepreviousornext

promptbypressingthe↑and↓arrows.

1 SelectRFsensor#(01to48).AssigntheDW10toanewzone.

2 SelectRFsensortype.

(01)Entry/Exit1

(02)Entry/Exit2

(03)Perimeter

(23)noresponsetype

3 SelectRFequipmenttype.

(1)contact

4 SelectRFsensorequipmentcode.Enter0862fortheDW10‐3452GIGThinDoor/WindowContact.

5 EnterRFsensorserialnumber(7digits).

ManualEntry:Typeinthelast7digitsoftheTXIDthatisfoundoutsideoftheboxoronthebackofthedevice.

AutoEntry:WiththepanelinLearn‐inmode(pressShiftthenLearn)pulltheBatteryPullTabout.Th

ecorrectTXIDshouldappear.

AcceptthecorrectTXIDbypressingok.

Remember to press the ↓ arrow to connue going through the 2GIG system conﬁguraon prompts.

6 SelectRFsensorequipmentage(0to1).

(0)new(productisnew)

(1)existing(productalreadyexists)

7 SelectRFsensor1loopnumber(1to3).

(1)UsesLoop1

(2)UsesWireleadLoop2

(3)UsesExteriorSwitch(magnetonly)

8 SelectRFsensor1dialerdelay.

(0)disabled

9 ConstructRFsensorvoicedescriptor.PressInsertthenpressanynumberbetween002and255toaddaword.Forexample,ifyou

wantedtonamethisDW10as“masterwindow,”pressInsertthenpress140forMASTER.PressInsertthenpress251forWINDOW.

10 SelectRFsensorreports(0to1).

(0)disabled

(1)enabled

11 SelectRFsensorsupervised(0to1).

(0)disabled(sensordoesnotreportlossofsupervisionorlowbattery)

(1)enabled(sensorreportslossofsupervision)

12 SelectRFsensorchime(0to13).

(0)disabled(panelwillNOTchimewhensensorisactivated)

(1‐13)enabled(selectsavoiceand/orchimetosoundwhensensorisactivated)

13 Toprogramanothersensorclicknext.

14 Toexitprogramming,clickskipthenendandexit.Uponexit,thepaneltakesaseveralsecondstoreboot.

Testing

•OpentheDoor/WindowContact(separatethemagnetfromthesensor).ThisactioncausestheControlPaneltodisplaytheopenzone

withtheassigneddescriptorontopofthescreen.TheSecurityButtonbecomesyellow(showingthatazoneisopen).

Walk Test

1 FromtheInstallerToolbox,selectwalktest.

2 OpenandclosetheDW10.ThisactioncausestheControlPaneltodisplaythesignalstrengthoftheDW10.

3 ExittheInstallerToo l b ox.

Installing and Mounting

For internal switch usage, do the following:

1 Mountthesensoronthedoorframeandthemagnetonthedoor.Ifthesensorisusedondoubledoors,mountthe

sensorontheleast‐useddoorandthemagnetonthemost‐useddoor.

TIP: Ifpossible,locatesensorswithin100ft.(30m)oftheControlPanel.Whileatransmittermayhavearangeof350

ft.(106m)ormoreoutintheopen,theenvironmentattheinstallationsitecanhaveasignificanteffecton

transmitterrange.Sometimesachangeinsensororientationcanhe

lpovercomeadversewirelessconditions.

2 Makesurethealignmentarrowonthemagnetpointstothealignmentmarkonthesensor(seethefigureabove).

3 Placesensorsatleast4.7in.(12cm)abovethefloortoavoiddamagingthem.

4 Avoidmountingsensorsinareaswheretheywillbeexposedtomoistureorwherethesensoroperating

temperaturerangeof32to120°F(0to49°C)willbeexceeded.

5 Usespacers(notincluded)tokeepsensorsandmagnetsawayfrommetalormetallicsurfacessuchasfoil

wallpaper.

FCCID:WDQ‐DW10345

IndustryCanadaID:7794A‐DW10345

THIN DOOR/WINDOW CONTACT

Summary of content (2 pages)

PAGE 1
FCC ID: WDQ‐DW10345 Industry Canada ID: 7794A‐DW10345 THIN DOOR/WINDOW CONTACT INSTALL INSTRUCTIONS The 2GIG‐DW10‐345 is a Thin Door/Window Contact that can be installed on doors, windows, and many other objects that open and close. The sensor transmits signals to the Control Panel when a magnet mounted near the sensor is moved away from or closer to the sensor. The sensor has an external input that accepts N/C dry contact devices. The sensor is also equipped with a cover tamper for additional security.
PAGE 2
NOTE: Avoid mounting sensors in areas with a large quantity of metal or electrical wiring, such as a furnace or utility room. To mount the sensor, do the following: 1 2 Place the base of the sensor in the desired location and secure with the included screws (as shown in the previous figure). When mounting the magnet, line up the arrow on the magnet with the middle line on one side of the sensor (see figure on first page). Mount the magnet no more than 0.4 in. (1 cm) away from the sensor.