User Manual

ManualsBrands2GIG ManualsElectronicsGoControl Z-Wave Bulbz Smart Dimmable LED Indoor Flood Light (BR30 Style)

CONFIGURATION

The LBR30Z-1 supports the Conﬁ guration command. The LBR30Z-1 can be

conﬁ gured to operate slightly differently than how it works when you ﬁ rst install

it. Using the Conﬁ guration command you can conﬁ gure the following:

Parameter 1: Dim Level Memory

By default, the LBR30Z-1 bulb will go to full brightness when turned on. To have

the bulb turn on to the last dim level setting, set Parameter 1 to 1.

Parameter Length Valid Values Conﬁ guration Option

1 Byte

Bulb will be full brightness when turned on (default)

1 Bulb will turn on to the last dim level setting

Parameter 9: Dim / Bright Step Level

When the brightness is adjusted by the controller/gateway, how much the bulb

brightness will change is set by the programmed dimming step level.

Parameter Length Valid Values Conﬁ guration Option

1 Byte 1 - 99

Default = 1

The step level is small when the value is low

The step level is large when the value is high

Parameter 10: Dim / Bright Speed

When the brightness is adjusted by the controller/gateway, how fast the bulb

brightness will change is set by the programmed dimming step speed.

Parameter Length Valid Values Conﬁ guration Option

1 Byte 1 - 10

Default = 3

The step speed is fast when the value is low

The step speed is slow when the value is high

Example: If Parameter 9 is set to the default value of 1, setting Parameter 10

from 1 to 10 will equal the number of seconds it takes to dim down the bulb

when the bulb is turned off, i.e. 1 equals 1 second for the bulb to dim down and

turn off, 10 equals 10 seconds for the bulb to dim down and turn OFF.

Z-Wave Plus Features

The LBR30Z-1 contains a Z-Wave 500 Series Module that supports Z-Wave

Plus features. A Z-Wave certiﬁ ed portable or stationary controller can

communicate with the Z-Wave 500 Series Module.

Depending on the capability of the controller or gateway software, the following

operations can be performed with the Smart LED Light Bulb. Refer to the

controller or gateway manual for details.

• Turn the bulb ON and OFF.

• Dim the bulb.

• Add or Remove the Smart LED Light Bulb.

• Assign the Smart LED Light Bulb to a specific Group/Scene and/or to

include the bulb as part of ALL ON or ALL OFF system commands.

• Over-the-air firmware update by the gateway or static controller.

• Lifeline function which automatically notifies the associated modules and

the network that a manually reset device is no longer in the network, thus,

the corresponding association becomes invalid.

INTEROPERABILITY WITH Z-WAVE DEVICES

A Z-Wave network can integrate devices of various classes of products, and

these devices can be made by different manufacturers. The GoControl Smart

LED Light Bulb has Z-Wave certiﬁ cation which guarantees interoperability.

ASSOCIATION

The LBR30Z-1 supports one Group with ﬁ ve Nodes for lifeline communication.

Group 1 must be assigned the Node ID of the controller to which unsolicited

notiﬁ cations from the LBR30Z-1 will be sent. The Z-Wave controller should

set this association automatically after inclusion. You can associate up to ﬁ ve

Z-Wave devices to Group 1. Lifeline association only supports the “manual

reset” event.

For instructions on how to “set lifeline association” please refer to your wireless

controller instructions.

SPECIFICATIONS

Power Supply 120 VAC, 60 Hz

Brightness 650 lumens (Equivalent to 65 Watt incandescent light

bulb)

Power Consumption 7.5 Watts

Color Temperature 5000K

Bulb Lifetime 25,000 hour (equivalent 22.8 years based on 3 hours/

day)

Radio Frequency 908.4 MHz / 916 MHz

Wireless Range Up to 130 feet line of sight between the Z-Wave

Controller and/or the closest Z-Wave Repeater

Normal Operating Temp 77°F (25°C)

Repeater Ye s

Z-Wave

and Z-Wave Plus

are registered trademarks of Sigma Designs

and its subsidiaries in the United States and other countries.

REGULATORY INFORMATION

The LBR30Z-1 is certiﬁ ed to comply with applicable FCC and IC rules and regulations governing RF and EMI

emissions.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) This device must accept any interference received, including interference

received that may cause undesired operation.

FCC Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician to help.

• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment

IC Notice

This Class B digital apparatus complies with Canadian ICES-003

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Le présent appareil est conforme

aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux

conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout

brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

This device complies with the Industry Canada license exempt RSS standard(s). Operation is subject to the following

two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

WARRANTY

This Nortek Security & Control product is warranted against defects in material and workmanship for twenty four (24)

months based on three (3) hours of use per day. This warranty extends only to wholesale customers who buy

direct from Nortek Security & Control or through Nortek Security & Control’s normal distribution channels. Nortek

Security & Control does not warrant this product to consumers. Consumers should inquire from their selling dealer as

to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of Nortek Security

& Control for consequential damages arising out of or in connection with use or performance of this product

or other indirect damages with respect to loss of property, revenue, or proﬁ t, or cost of removal, installation,

or reinstallation. All implied warranties, including implied warranties for merchantability and implied warranties for

ﬁ tness, are valid only until Warranty Expiration Date as labeled on the product. This Nortek Security & Control LLC

Warranty is in lieu of all other warranties express or implied. All products returned for warranty service require a

Return Product Authorization Number (RPA#). Contact Nortek Security & Control Returns at 1-855-546-3279 for an

RPA# and other important details.

IMPORTANT !!!

Radio controls provide a reliable communications link and ﬁ ll an important need in portable wireless signaling.

However, there are some limitations which must be observed.

• For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices.

As such, they have limited transmitter power and therefore limited range.

• A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that

occur on or near their operating frequencies, regardless of code settings.

• Changes or modifications to the device may void FCC compliance.

• Infrequently used radio links should be tested regularly to protect against undetected interference or fault.

• A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer,

and these facts should be communicated to the ultimate users.

PRINTER’S INSTRUCTIONS:

INSTR,INSTL,LBR30Z-1; P/N: 10006193 X8; INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: 8.500” x 11.000”; TOL ± .125”; SCALE: 1-1; FOLDING: 4-FOLD ALTERNATE; SIDE 2 OF 2