MAXX-2420-EX™ High Definition Video Server Operations Manual P/N 100-145-0022-01 June 2012 Software Version 1.08.
Page 2 MAXX-2420-EX Owner’s Manual
Contents Preface________________________________________________________________ 9 Software and Operations Manual Revisions ..................................9 Safety Notices_________________________________________________________ 10 Safety Terms and Symbols .......................................................... 10 General Safety Caution............................................................... 10 Personal Injury Precautions ........................................................
Graphic User Interface Overview ........................................................... 30 System Menu Bar ....................................................................... 31 Show Menu ............................................................................... 31 Edit Menu .................................................................................. 31 Windows Menu ......................................................................... 31 Help Menu .....................................
Sorting Clips .............................................................................. 57 Filtering the Clip Display............................................................ 57 Finding Clips.............................................................................. 58 Finding Clips Using Wildcards ................................................... 58 Finding Clips Using Regular Expressions .................................... 59 Using Playlists...................................................
Network Time Protocol ________________________________________________ 88 Automatic Date/Time Updates.................................................... 88 Connecting to the Internet .......................................................... 88 Configuring NTP ........................................................................ 89 Selecting the Time Zone.............................................................
Program Updates from USB Memory ................................................... 118 Updating Firmware .............................................................................. 119 Replacing a Hard Drive........................................................................ 121 Factory Repair Policy ........................................................................... 122 Regulatory Certifications ...................................................................... 122 Safety ..............
Preface This manual provides installation, setup and operating instructions for 360 Systems’ MAXX-2420-EX video server. It is organized to provide quick access to topics of primary interest. An extensive Table of Contents is provided at the beginning, and a subject Index at the end, to assist in locating information. If you have already used other video servers or VTRs, you may find discussion of the basic server to be covering familiar topics.
Safety Notices Safety Terms and Symbols THE FOLLOWING WARNING SYMBOLS ARE USED IN THIS MANUAL: ENGLISH FRANÇAIS ITALIANO ESPAÑOL ENGLISH FRANÇAIS ITALIANO ESPAÑOL ATTENTION: REFER TO OWNER’S MANUAL FOR IMPORTANT INFORMATION. ATTENTION: VEUILLEZ VOUS RÉFÉRER AU MODE D’EMPLOI POUR UNE INFORMATION IMPORTANTE. ATTENZIONE: FATE RIFERIMENTO AL MANUALE PER INFORMAZIONI IMPORTANTI. ATENTCION: FAVOR DE REFERIR AL MANUAL DE OPERACION POR INFORMACION IMPORTANTE. WARNING: ELECTRICAL SHOCK HAZARD.
Important Safety Instructions These instructions are required per applicable safety standards. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8.
Product Damage Precautions • 360 Systems’ MAXX-2420-EX™ server contains hard disk drives and other fragile electronic and mechanical devices. While designed to be very reliable, it is still vulnerable to shock. Handle with care, and exercise caution not to drop or bump the server as damage to internal components may result. Always turn off power before moving the server. • Do not obstruct air vents. Maintain an ambient temperature below 30°C (86°F). • Clean only with a soft cloth dampened with water.
Introduction 360 Systems’ MAXX-2420™ server is a four channel, high-definition video recorder/server designed for broadcast, production, and Pro A/V applications. It can play four independent video streams at once, and stores approximately 330 hours of JPEG-2000 encoded video1 with eight audio channels per video stream. It occupies just 3½” of rack space.
Compatibility with Automation Controllers MAXX servers work with automation controllers from many different manufacturers, accepting VDCP, Odetics or BVW protocols for 9-pin control of each server channel. 360 Systems’ business partners provide automation controllers for applications ranging from affordable systems for ProAV, up to large-scale broadcast solutions. Contact a 360 Systems application engineer or an automation provider for assistance with your requirements.
System configuration is clear and straightforward through the GUI. It provides access to encoding parameters, audio options, and time-code settings. Whenever new server features are installed, new set-up parameters and user-interface features become immediately available. The server comes with Remote Workstation Software, which allows it to be remotely operated from a standard PC over Ethernet; the GUI is replicated at each remote location.
Key Features and Benefits The MAXX-2420-EX is designed from the ground up to deliver outstanding performance and value as a high-definition broadcast server. Two inputs, four outputs, a Gigabit Ethernet port, and multiple audio formats make it an excellent and affordable choice for the transition to high definition.
Applications for 360 Systems Servers The MAXX-2420-EX adds value to many applications in broadcasting, cable distribution, video production, Pro A/V, entertainment and sports. It provides immediate record and playback of any source, lending a spontaneous appearance to broadcasts, presentations and live events.
Accessory Information AXP-3 Multi-Channel Analog Audio Module (optional – provides audio channels 1-4) Provides 4 analog audio outputs for each of 4 server video outputs, and 4 analog audio inputs. +4 dBu balanced on XLR connectors. Redundant power supply. 3½” [88 mm] height. AXP-4 Multi-Channel Analog Audio Module (optional– provides audio channels 5-8) Provides 4 analog audio outputs for each of 4 server video outputs, and 4 analog audio inputs. +4 dBu balanced on XLR connectors. Redundant power supply.
Installation Unpacking Your server has been carefully inspected and calibrated before shipment to allow immediate operation upon installation. Check all items for signs of visible damage which may have occurred during shipment. If any item is damaged, contact the carrier to file a claim. Keep the packing materials in the event that a unit must be returned.
Important Installation Notes System Cooling When many pieces of equipment are mounted in an equipment rack, a considerable amount of heat may be produced, which must be removed efficiently. Further, a lower operating temperature will make equipment operate more reliably, and it will last longer. In the extreme case, excessive temperatures cause rapid equipment failure, and damage which can be difficult to repair. Heat in an equipment rack must be removed by forced air.
Continuous Conversion UPS Design This improved design, sometimes called ‘double conversion’ continuously converts utility power to DC, stores it in a battery, then produces isolated AC power from an inverter. It never switches back and forth to utility power, and has better immunity to input transients, brownouts, and blackouts.
About Server Software The MAXX-2420-EX is shipped with its application programs and operating system installed. The first time that it is started, it must be connected to a keyboard, monitor and mouse. The server will ask you to accept the Software Licensing Agreement before it will operate. This screen will only appear during the initial startup. Refer to the Maintenance chapter of this manual if it becomes necessary to reinstall software.
Connect the keyboard to the PS-2 keyboard port on the rear of the unit; connect the mouse to the mouse port. Refer to Figure 1 on page 24. NOTE: If the mouse and keyboard connections are interchanged, the MAXX-2420-EX may not boot up properly. Be especially careful about this when using extender cables. See USB Ports on page 26 for information on using USB keyboard and mouse.
Rear Panel Connections Figure 1 indicates the Rear Panel connections on MAXX-2420-EX. Each connection is described briefly in the following text. Make all connections appropriate to other equipment before applying power to the MAXX-2420-EX.
CVBS Monitor Outputs (Optional) Channels 1, 2, 3 and 4 have letterboxed composite video monitoring outputs. Genlock Sync Reference The MAXX-2420-EX is designed to be referenced to an external genlock source in the form of RS-170 black. The GENLOCK input provides a fixed 75-ohm termination. An internal crystal reference is also provided so that the server can be used as a stand-alone player. Gigabit Ethernet Port A Gigabit Ethernet port is provided on the MAXX-2420-EX.
USB Ports The rear panel USB ports are used for software updates. As of version 1.07.559 the USB ports can support keyboard and mouse operation, but it is still recommended to use PS-2 devices. Currently, a PS-2 keyboard is required for update operations using a USB drive as the limited operating system on the USB drive does not support USB keyboards.
Control Module (CXP) Connections The CXP Module provides connections to the server’s serial ports and its GPI interface using a 68 pin cable. Connect it between the back of the CXP module and the CXP port on the back of the server. CAUTION!! Do not plug the CXP Module into the AXP audio module connection on the server. Damage to the system may occur. The CXP connector on the MAXX-2420-EX is clearly marked. Connect the CXP module per Figure 3. Be certain it is properly connected before applying power.
contacts or to an open-collector transistor output. GPI inputs are programmable, and can provide machine control such as PLAY, STOP, or RECORD through simple external switches. The MAXX-2420-EX also provides twelve GPI outputs which may be used to confirm that a command has been received, or for other purposes. The function of these open-collector outputs is programmable; they may be used to operate an LED, or they can drive a suitable logic input.
Basic Operations This section introduces the Graphic User Interface (GUI), its menus and operating controls. If you want to skip ahead to learn how to record a clip, go to page 39. Skip to page 46 to read about playing a clip. The graphic user interface is the primary way to manage server operations. With it, you can control recording and playout, set up video and audio formats, map remote control ports to video channels, perform editing and make playlists.
Graphic User Interface Overview Once the server has successfully powered up, the VGA monitor will display the GUI of Figure 5. This view provides: • A main System Menu bar for configuration operations • A Status Bar that displays various system messages • Four VTR-like transport controls, one for each video channel Figure 5: Graphic User Interface with Clip Transport Windows When using the mouse, all buttons of all channels will operate immediately, without first selecting a window to activate it.
System Menu Bar The System Menu bar contains four menus: Show, Edit, Windows and Help. Show Menu Contains selections for the four Channels and the clip management windows. Channel 1 Channel 2 Channel 3 Channel 4 Opens the specified window if it is closed, brings it to the top and activates it. Key Commands – F1, F2, F3, F4 Clip List Opens the Clip Navigator window if it is closed, brings it to the top and activates it. See page 57. Key Command – Ctrl+L. Find Clips Opens the Clip Locator dialog.
In addition, there are selections for each open transport window. Selecting one of these brings that transport to the top of the display and makes it the active window. Help Menu Contains a single item, About, which displays the server software versions, serial number and Unit ID. The Status Bar A status bar appears at the bottom of the window that provides system information including GENLOCK, VIDEO INPUT DETECTED, and TIME REMAINING—PERCENT FULL.
The Transport Channel View The Transport Channel View is shown in Figure 6. This is the default view of each channel. Basic transport operations such as play, stop, record, and head/tail trimming appear in the Clip Transport window for each channel. These operate in familiar VTR fashion. Figure 6 - Transport Channel View Transport Menu Bar There are two menus, File and Options. File Menu New Channel 1 and 2 only.
Save As Opens the Clip Navigator to allow saving an edited version of the clip with a new name. This allows making alternate versions of a clip or making multiple segments of a master clip. Key Command – Ctrl+A. Playlist Switches from Transport View to Playlist View. Close Closes the Transport window. This has the same effect as the Close box in the upper right corner of the window. Note that this will not stop playback or eject a loaded clip. Options Menu This menu contains two selections.
The Playlist Channel View The Playlist Channel View is shown in Figure 7. This view allows multiple clips to be loaded in a playlist for sequential playout. Figure 7 - Playlist Channel View Playlist Menu Bar There are two menus, File and Options. File Menu Open Opens the Clip Navigator to allow choosing a clip to load into the transport. Key Command – Ctrl+D. Append Opens the Playlist Selection dialog to allow choosing a Playlist to Append to the currently loaded list.
Save As Opens the Clip Navigator to allow saving an edited version of the clip with a new name. This allows making alternate versions of a clip or making multiple segments of a master clip. Key Command – Ctrl+A. Rename Opens the Playlist Selection dialog to allow renaming the currently loaded Playlist. Transport Switches from Playlist View to Transport View. Eject Ejects the currently loaded Playlist in preparation for creating a new one. (It is not necessary to Eject a list to load another saved list.
Initial System Configuration Selecting a Sync Reference In many applications, this server and downstream equipment connected to it must be referenced to a common genlock source (SMPTE 170M or ITU-R-BT.470). A BNC connector is provided on the rear panel to receive a genlock signal. It has a 75-ohm termination. An internal crystal reference is also provided so that the server can be used as a stand-alone player, and also for convenience for testing.
Selecting a Video Format The MAXX-2420-EX can record and play video in four high definition video formats: 1080i @ 59.94 Hz 720p @ 59.94 Hz 1080i @ 50 Hz 720p @ 50 Hz To select a video format: • Go to Edit>Configure>Timing dialog on the GUI. • Select a check-box for the rate at which you will record or play. A reminder will appear, to stop video on all channels and prepare for automatic restart in the new format. This takes at least 12 seconds, so the change should not be performed on-air.
Making a Recording from the GUI Video recordings are made using the Transport View of Channel 1 or 2. These channels can record or play clips, but not both at the same time. Channels 3 and 4 are playback only. The following steps are used to make a recording. Most configuration settings can be skipped once a workflow is established. Channel 1 is used below as an example; all instructions apply equally to channel 2.
Setting the Audio Input Source Select OPTIONS >CONFIGURE from the Channel 1 Transport Window. The Dialog box in Figure 9 appears. • Select an Audio Input by clicking the desired button. • Click APPLY or OK. Embedded audio is eight tracks contained in the HD-SDI video stream. AES/EBU Digital Audio refers to audio input from the optional DXP-1 multi-channel module. Analog Audio refers to audio input from the optional AXP-3 and AXP-4 multi-channel module.
Figure 10 - Audio Delay Time Offset Audio Rate Conversion • Converting the sample rate for audio applies only to AES/EBU digital audio. It is not relevant to analog audio, or Embedded audio. Select OPTIONS > CONFIGURE from the Channel 1 Transport Window. The dialog box in Figure 5 appears. • Check a box under Audio Rate Conversion only if the corresponding AES/EBU audio source is not a video-referenced 48K sample rate (as with wild audio or 44.1K audio). • Click APPLY or OK.
Setting VANC Line Selections • Select OPTIONS >CONFIGURE from the Channel 1 Transport Window. The Dialog box in Figure 9 appears. • Check the VANC box if Vertical interval ANCillary data (VANC) is to be recorded along with video. • The VANC line selection data entry box will become active. Enter desired line numbers, separated by a comma. Ranges can be specified with a dash, such as “9-12”. Lines 9,10 11 and 12 will be included. • In 720p, enter up to 12 lines. In 1080i, enter up to 6 lines.
Making a Crash Recording Press Record whenever Channel 1 reports that it is IDLE. Making a Named Recording • From the Channel 1 Transport Window, Select FILE>NEW. The dialog of Figure 11 appears. Figure 11 - Channel 1 Clip Navigator "New" mode • Enter a clip name using the keyboard. Up to 31 characters may be used. Spaces are allowed; however, some characters other than upper or lower case letters and numbers may not be used. These characters will not enter into the name field when typed.
Figure 12 - Channel 1 Ready to Record • Click the RECORD button at any time to begin recording. The yellow time display counters will update the clip duration continually. • To stop recording, click STOP. Note: An in-progress recording must be 2 seconds long before it will appear in the clip list. Hitting the STOP button to end the recording after less than 2 seconds will also cause the clip to appear in the clip list.
Under automation control, Auto E-E behavior is slightly different than under GUI control. The server will remain in E-E ON mode until a transport control command (Play, Stop, Jog, etc) is received. After receiving such a command, the server will remain in E-E OFF mode until record mode is entered. In record mode, E-E mode is ON. As with GUI operation, automation controllers may send E-E ON and E-E OFF commands to override the automatic operation.
Playing a Clip from the GUI Video Playback can be done on all four channels, individually or simultaneously. The recordcapable channels (1 and 2) can record or play, but not both at once. Follow these steps to play a clip: Beginning Playback 1. Select FILE >OPEN from the Transport Window of Channel 1, 2, 3 or 4. The Clip Navigator shown in Figure 13 appears. 2. Navigate the folder structure if necessary by clicking on the folders. 3. Select the clip to be play by double-clicking it. 4.
Ejecting a Clip Ejecting a clip effectively removes it from the transport. The channel will output Black. Press EJECT to eject a clip. Using Jog The JOG + command will move to the next frame and go to Still. The JOG – command will move to the previous frame and go to Still. Using Go To Frame and the Frame Locator Click the arrows |< or >| to go to the next trim point (Mark In or Mark Out) in the selected direction.
the Shuttle control. For faster playback from the GUI, use the FAST FORWARD or REWIND buttons as described in the preceding section. In sports, slow-motion control is usually accomplished with a desk-top slow-mo controller, such as those made by DNF Controls and others. These provide a hands-on experience far preferable to using the GUI. Using Shuttle to Control Playback Speed The Shuttle Control is a slider bar that controls playback speed.
Editing a Clip Edit controls are activated with the Edit check box. Several buttons are available to define the beginning and end of a region within a clip; associated time code displays are also present. These non-destructive Mark In and Mark Out trim points can be set to define a portion of a clip to be played.
The values in this display window may be set by two methods: • Enter Mark In point from the keyboard: Use the mouse or Tab key to move between In and Out fields. When a field is highlighted, enter a numeric value from the keyboard. • Whether a clip is still or playing, press Mark In to capture a time code value from the clip’s current position. Marking the Out Point Sets the current time code value into the Mark Out point time display.
System Configuration The following configuration options apply to the server as a whole, except where it applies specifically to an individual channel. Assigning Names to the Server and Transport Channels The server can be assigned a name that will be displayed along the top of the Main GUI Window. Each individual server channel can also be given a name. To assign a name to the server or transport channels, click EDIT>CONFIGURE>NAMES from the main menu pulldown. The screen of Figure 14 is displayed.
Programming GPIO Outputs The MAXX-2420-EX has twelve General Purpose Outputs, referred to as GPO 1 through 12.
Programming GPI Inputs The MAXX-2420-EX has 12 General Purpose Inputs, referred to as GPI 1 through GPI 12.
Figure 16 - GPI Configuration Screen Configuring the Ethernet Network MAXX-2420-EX provides a number of user settings that configure it for use in a practical network. These will be found on the Configure Network tab shown below. The NET-1 Ethernet port on the server has a unique IP Address. In this way, each server can be identified on the network. Network Settings Tab Use the Main Menu selection bar at the top of the server GUI to configure network communication settings.
Disable Network [X] This selection turns the network OFF or ON. The default is Disabled (the box is checked). To Enable the network connection, click the box to un-check it. Disabling the network can be used to deny access to the server from the network for security purposes. Enabling/Disabling DHCP [X] Enabling DHCP will configure the network interface automatically. If the DHCP box is not selected, the user may then manually enter assignments in the following windows: • IP Address ( Example: 192.168.1.
Setting the Date and Time Click EDIT >CONFIGURE >DATE/TIME. The dialog below appears. Figure 18 - Time/Date Configuration Screen Select the REGION and ZONE according to your geographic location or time zone. Use the scroll-bar as necessary, and then click on the desired value. Set the TIME and DATE by clicking on the Time/Date field and navigating the clock and calendar. Check Automatic Updates to enable automatic updates using the Network Time Protocol (NTP). Refer to Network Time Protocol on page 88.
Clip Navigator The MAXX-2420-EX’s Clip Navigator is used to find, select, delete, name, and rename clips. Clips can be dragged and dropped anywhere on a Transport for immediate playback. Single or multiple clips can be dragged into a Playlist. See page 62. • Click SHOW >CLIPLIST from the main pulldown menu to display the Clip Navigator. Figure 19 – Clip Navigator Renaming and Deleting Clips Clips can be renamed by right clicking on them with the mouse, then selecting Rename from the pop-up menu.
Finding Clips Clips can be easily found using the Clip Locator. To locate a clip: 1. Click SHOW>FIND CLIPS. The Clip Locator screen of Figure 20 appears. 2. Check Case Sensitive to make the search case-sensitive. 3. Check Stop After First Match to find only the first match. 4. Check Use Regular Expressions to search for the string of interest ANYWHERE in the clip name. With Regular Expressions unchecked, the search will match only clips that BEGIN with the string entered at FIND.
Finding Clips Using Regular Expressions A regular expression (“RE”) specifies a pattern to be matched in a clip name. Regular expressions can contain both special and ordinary characters. Ordinary characters just match themselves. Thus, the RE “night” would match the “night” in the clip name “Tonight Show”, so this and any other clip name with “night” in it would be placed in the list of found clips. The following special characters are supported: . (dot) This matches any single character. “a.
Using Playlists MAXX-2420-EX’s Advanced Playlisting software provides extensive tools for building, editing and playing complex sequences of program content. Advanced Playlisting appears as on-screen windows, with an intuitive Graphic User Interface that makes it easy to operate without extra equipment. It’s invaluable for building commercial breaks, news rundowns, still-store and clip lists. The server will create and store as many playlists as needed, each with its own unique name.
The Playlist View The playlist view for channel 1 is shown in Figure 21. Its functions are briefly described here. Table 1 provides an overview of Playlist control functions and their associated hot-keys.
Creating and Running a Playlist To Create a Playlist (Using Channel 1 in the example): 1. Change the transport for Channel 1 to the Playlist View. Click FILE >PLAYLIST in the Channel 1 transport pulldown menu. The window of Figure 22 appears. 2. Click the EDIT check box to put the channel into edit mode. 3. Click SHOW >CLIP LIST from the main menu to open the Clip Navigator. Both windows are now visible. 4. Double click on a clip in the Clip Navigator to add it to the Playlist.
Figure 23 – Active Playlist 7. To SAVE the Playlist select FILE >SAVE-AS. Enter a file name. Click SAVE. 8. To SAVE an existing playlist without changing the name, use FILE >SAVE. Loading a Playlist (FILE>OPEN) Click FILE >OPEN from the Playlist View to bring up the list of available Playlists. Double-click on a playlist to load it. Saving a New Playlist (FILE>SAVE AS) Once a Playlist has been created, it can be saved by selecting FILE >SAVE AS from the Playlist View pulldown menu.
Stopping a Playlist (STOP) Click STOP to halt a Playlist. Pausing Playlist (PLAY/PAUSE) When a Playlist is running, the PLAY key will change to indicate PAUSE. Pressing PAUSE stops the Playlist immediately, on the current frame of a clip. Pressing it again will resume playback. Cueing a Clip (CUE) When the Playlist is running, click CUE to immediately prepare a selected clip for playback. When the current clip is finished playing, the Playlist will play the Cued clip, followed by all subsequent clips.
Automatic Scrolling to Currently Playing Clip (HOME) Click HOME to make the currently playing clip visible in the Playlist View window. If no clip is playing, then the currently-cued clip is displayed. This is helpful if you have manually scrolled elsewhere in a large Playlist.
Editing Playlists Removing Clip from a Playlist To remove a Clip from a Playlist: • Make sure the clip to be removed is not PLAYING or CUED. • Position the cursor over the Clip and right-click. Select REMOVE from the pulldown menu. Removing Clips Above or Below the Selected Clip All clips above or below the selected clip can be removed unless a CUED or PLAYING clip is affected. These options will “grey out” if removal is not allowed for this reason.
Changing Duration of Clips in Playlist Make sure the EDIT checkbox is checked in the Playlist View window. Position the cursor over a clip and right-click. Select EDIT DURATION from the pulldown menu. Enter a duration in the Duration window. The minimum duration is 4 seconds.
Figure 25 - GPO Configuration Screen Figure 26 - GPO Editor Mapping GPI to Control a Playlist Playlists can be controlled with the twelve GPI Inputs. See Programming GPI Inputs on page 53.
Advanced Topics System Timing The MAXX-2420-EX is equipped for use with an external genlock signal as a timing reference. This causes all outputs to be synchronous with other video signals in a facility. Adjustment of Genlock Timing will fine tune this synchronization to compensate for differences in equipment and wiring. This global setting for all outputs allows timing to be varied by one line of video. The Vertical (lines) setting rarely needs to be adjusted.
Using Embedded Audio The MAXX-2420-EX provides 8-channel embedded audio capability. Features include: • Synchronous 20-bit audio at a 48K sample rate. Non-genlocked audio and other sampling rates are not supported. • The server records and plays Group 1 and 2 audio, (channels 1-8). Up to 16 channels of audio may be present in some HD-SDI streams. • In E-E mode, all embedded audio channels will pass through the server unaltered.
Ganging Channels for Synchronized Playback Two video channels can be ganged together for frame-accurate playback. This may be used for key and fill material (either stills or clips), or multi-channel playout of presentations, such as synchronized matte backdrops on News Broadcasts, or multi-screen projection. The channels can be ganged in the following combinations: • • • Channel 1 controls Channel 2 and/or Channel 3 and/or Channel 4.
Note that the VDCP checkbox option to “show first frame” for a Cue command is ignored for channels in ganged mode. The automation system must issue a Still command to Channel 1 to achieve this effect. Ingesting a TARGA file via FTP automatically creates a key clip and a fill clip, each a single frame in length. For example, if file “xyz.tga” is transferred to a server via FTP, then a pair of single-frame clips is created: “xyz” and “xyz_” containing the fill and key material.
over 2GB. This can be an issue when attempting to Export directly to network storage locations. In practice this amounts to a maximum clip duration of about 4 seconds. There is an indeterminate time limit somewhere above 1 minute that is dependent on the amount of detail in the material. (This is program dependent because it is on the postcompression side of the transcoding process.) The resulting .mov file may be sent to the server by FTP, logging in as user “anonymous” or “ftp”. No password is required.
FTP File Transfers The MAXX-2420-EX connects over Gigabit Ethernet using an RFC-1359 compliant FTP server. File transfers to and from the server are managed from an FTP client file transfer program running on a Windows® or Macintosh® computer. This provides a rapid way to execute drag-and-drop file transfers; it can also manage many servers at once and does not tie up the server GUI, which may already be in use. Table 2 indicates the supported FPT client list. FTP Client Version Platform Flash FXP 3.2.
When connecting directly to a PC or Laptop, configure the server as IP address 192.168.1.3, netmask 255.255.255.0 and disable DHCP. In the PC, double click on the Local Area Connection Icon in the system tray or in the Network and Dial-Up Connections in the Control Panel. In the Local Area Connection Status dialog, click on Properties. Click on the item “Internet Protocol (TCP/IP)” and click on Properties again.
Transfer Time for 1 minute of video Workload Upload to MAXX Download (or MAXX-to-MAXX FXP transfer) IDLE 14 seconds (45.0 MB/s or 360 Mb/s) 28 seconds (22.5 MB/s or 180 Mb/s) 1 Channel Playing 14 seconds (45.0 MB/s or 360 Mb/s) 28 seconds (22.5 MB/s or 180 Mb/s) 3 Channels Playing 15 seconds (39.4 MB/s or 315.2 Mb/s) 45 seconds (14.0 MB/s or 112 Mb/s) 17 seconds (37.0 MB/s or 296 Mb/s) 44 seconds (14.3 MB/s or 114.
When transferring files as mxf, only the material between the edit points is transferred. This means that: • Transfer of a file with head and tail points set will remove portions before the head and after the tail. The original length of the file cannot be referenced in a restored copy. • Transfer of a master file and (non-overlapping) subclips of that file will result in duplication only of the material defined by the subclips.
Before Transfer (On Source MAXX) 00:30:00;00 00:00:00;00 CLIP_A 00:10:00;00 (IN POINT) 00:10:00;00 00:20:00;00 (OUT POINT) 00:20:00;00 CLIP_A.vfc Figure 29 – Result of a VFC file transfer Bit Rates of Transferred Files Reported in the Clip Navigator JPEG2000 as implemented in the MAXX-HD is a variable bit rate compression technology. What this means is that the actual bit rate (amount of video data) that is created is dependent on the level of detail in the images in the video frame being encoded.
The following formats are supported: JPEG-2000 (.mxf) JPEG-2000 files wrapped in the .mxf format. The mxf type is Operational Pattern OP1a. The audio is 24-bit 48KHz PCM (uncompressed) in 8 individual tracks. These files are compatible with the Edius non-linear editing program from Grass Valley. See the next section for more information. JPEG2000 format .mxf files from the Grass Valley Infinity camcorder are also compatible. JPEG-2000 (.vcf) JPEG-2000 files are also available in .
Use File>Export>Quicktime Conversion (this is specific to Final Cut Pro, other programs may differ). Settings: Frame Rate = usually can be Current to reflect the timeline setting, but the rate for 720p is 59.94, the rate for 1080i is 29.97 with Field Dominance set to Upper (Odd). (Note that some Quicktime codec user interfaces use fps, which may mean either fields or frames. If you ever have issues with run time being halved, use 29.97. If run time is doubled, change to 59.94.
Using MAXX-HD with the Edius NLE Edius is a non-linear video editing program for PC computers available from Grass Valley Group. It is a full featured editor including titling, video effects, audio processing and compatibility with a wide variety of video formats. MAXX-HD files can be placed directly on the timeline without any transcoding, and rendering time for unmodified video sections is extremely fast as no transcoding is required.
The Select Exporter Plug In dialog appears. In the window on the left, select Infinity. In the Exporter section in the window on the right, select Infinity JPEG2000. Select Export Between In and Out if desired. This allows exporting of only the portion of the timeline between the In and Out markers. Select Enable Conversion. Click on the arrow next to Advanced to expand the dialog. In the Advanced section, set up the parameters as shown in Figure 30 for 1080i, or Figure 31 for 720p.
Figure 31 – 720p Configuration Click on the Disk icon at the bottom of the Select Exporter Plug In dialog (see the bottom of Figure 30) to save the settings as a Preset. Enter the desired Preset Name and Description. The recommended bit rate is 75 Mbps. The Audio Format is 24bit/8ch, even if your source is 16 bit or fewer channels. If most of your output will be for the MAXX-HD, click Save as Default to set this as the default configuration for Export (again refer to the bottom of Figure 30).
Figure 32 – Export Dialog Select the Folder option and click Browse to specify the output directory. Enter a Clip Name. Leave Playlist selection set to “Same as clipname”. Click OK to start the Export.
For this example the output directory was F:\HDVideoFilesOn13T\Edius. After the export, two folders are created there, Clips and Playlists. The Playlists folder is unimportant; the Clips folder is where the output folders will be found Each clip has its own folder. In this example, the Clip name was ExportExample. The first time this name is used, a folder is created with the name ExportExample_0001.icf. When a name is used again, the number is incremented, as can be seen at right.
Creating a Project and a Project Preset When using Edius to edit video primarily sourced from the MAXX-HD, there is no question that the project parameters detailed here should be used. However, if you are primarily using material from other sources, or delivering to other formats, it may be more efficient to use other Project formats and simply rely on the Export process to output to JPEG2000.
Figure 33 – 1080i Project Configuration Figure 34 – 720p Project Configuration Note that the VA track includes a stereo audio track, so the 6 “A” tracks make up the remainder of the 8 tracks used by MAXX-HD.
Network Time Protocol Automatic Date/Time Updates When using server play-lists in broadcast applications, an accurate record is often needed of what was played and when. The server’s As-Run logging feature creates such a record, time stamping each played clip using the machine’s internal date/time clock. Very accurate time stamping can be achieved by synchronizing the server’s clock to an external time base that is referenced to Coordinated Universal Time (UTC).
Configuring NTP The server GUI is used to set the time zone and to enter the networking parameters. The local GUI must be used, as these configuration screens are not available on the Remote Workstation Interface. Selecting the Time Zone Starting at the main menu bar, Click Edit >Configure >Date-Time screen. When “Automatic Updates” is not checked, the Region and Zone lists are enabled. Select your region and then the zone within that region.
Entering Network Parameters From the GUI’s main menu bar, click EDIT>CONFIGURE>NETWORK. The following screen appears. Make sure the basic network parameters have been entered. Figure 37 - Network Configuration Screen Disable Network: uncheck Host Name: (Any name will suffice, but since this name appears on each line of the server’s diagnostic logs, it is a good idea to keep this short.) The name should also be unique from other devices on the network.
The nonprofit Internet Systems Consortium, Inc. (ISC) maintains sites that automatically return lists of public time servers to an NTP client such as the server. Hence, the NTP Servers field is initially filled in with the URL’s for these sites (0.pool.ntp.org, for example). Of course you can overwrite this list with the addresses of specific time servers you may want to use. However, if you try to clear the NTP Servers field it will be reset to the default list.
Automation Control MAXX-2420-EX’s serial control inputs connect with many broadcast automation systems, instant replay panels, video switchers, and remote control devices. For compatibility with simple controllers and push buttons, the server also provides 12 GPI (contact closure) inputs, and 12 programmable command outputs. Remote Serial Control The server’s four 9-pin RS-422 serial control inputs permit control of their associated video channels.
Controller Priority Only one serial controller can control a given video channel at a time. In general, the first controller to gain control of a video channel will have exclusive command. This prevents conflicting instructions that would cause unexpected behavior. The only exception is that the graphic user interface can immediately take control of a channel by deselecting Serial Control in that channel’s dialog window. External controllers are prohibited from taking control away from the GUI.
Figure 39 - Serial Port Configuration Screen Setting the Automation Source Directory By default, automation equipment will access the Home or Root directory as a source of clips. The directory accessed by automation equipment can be set for each port as follows. Select the port to be used (COM1, COM2, COM3 or COM4). Click on the FOLDER icon in the PATH field of the Serial Port Configuration Screen. Navigate to the folder to be accessed by automation equipment.
Segregating material for different broadcast channels • • Content can be placed in a folder for each channel, and played out by separate automation systems or controllers. Each channel can run completely independently – there can be duplicate file names with different content, and the opportunity for airing content on the wrong channel is greatly reduced. Content that is common to both channels can be copied into both directories.
This option is very seldom used; it allows preroll commands to be ignored and assumes that the operational preroll is 4 frames. Do not check this unless you experience problems with frame accuracy on recordings and playback transitions. Start with a setting of 4 frames on the automation system and adjust until you achieve proper timing. Auto E-E Toggles Auto E-E mode (input monitor) on/off.
Tested Automation Controllers The server has been tested by 360 Systems and the manufacturers of equipment listed below, and found to operate correctly. This list is not comprehensive, and the inclusion or absence of a product does not indicate a preference for any make or model. Operational variations do exist between makes and models. Manufacturer Controller Protocol Notes HARRIS AUTOMATION ADC-100 VDCP ALL HARRIS CONTROLLERS SAME SUNDANCE FAST BREAK VDCP NVERZION EMC-NT VDCP CRISPIN CORP.
Remote Workstation Interface The Remote Workstation Interface is a software application that provides control of the server from PC workstations located within a facility. A remote workstation can access one or more video channels of the server to perform ingest, playback, trimming, playlisting, traffic operations or monitoring of server activities.
Figure 40 - Remote Workstation Deployments About the Remote Workstation Interface The Remote Workstation Interface consists of a CD-ROM or USB flash drive carrying the Remote Workstation application for Windows XP, Vista or Windows 7 computers. It selfinstalls using the normal Windows prompts. It is possible to install the Remote Workstation software on a number of PCs; any of them can then control one or more channels of one or more servers.
Installation To install Remote Workstation software from CD-ROM or USB drive, insert the media into the PC. • The auto-run capability of Windows will start the Remote Workstation setup program. If it does not, select the Run… option of the taskbar Start Menu and type: D:\setup.exe. If necessary, replace D:\ with the drive letter of the flash drive. • You will be prompted to enter the IP address of the server you wish to control. If you know the address, enter it here.
Hard Disk Management MAXX-2420-EX employs an advanced Serial-ATA controller that manages eight high-capacity hard disks operating in a RAID-5 configuration. This design increases system performance, and by storing parity data, can survive the complete loss of a drive in the array without data loss. The MAXX-2420-EX brings a high level of reliability to Serial-ATA RAID through a switched architecture that exceeds the reliability of SCSI shared-bus storage systems.
About RAID 5 A RAID 5 configuration features the data striping of RAID 0, combined with the parity benefits of RAID 4. Using a parity (exclusive OR) function, RAID 5 can tolerate the loss of one drive. Parity information is distributed across all drives rather than being concentrated on a single disk. This avoids throughput loss due to contention for the parity drive. Spare drives can be used to rebuild an array after a drive is replaced. RAID-5 capacity equals the size of drive times (number of drives -1).
Managing Disk Arrays The MAXX-2420-EX’s Disk Array Configuration Utility provides tools for monitoring and managing the disk array. Monitoring and troubleshooting programs automatically check the array, report problems and provide access to RAID status information and service options. If up to two drive faults should occur, it should not cause data loss; but remember that the drive array is degraded and no longer has fault tolerance.
IMPORTANT The term “DEGRADED” refers to the state of the Array data, not necessarily the hardware or disk drives themselves. It indicates that the parity information that protects the data is not up to date. While it can be caused by hardware problems, it can also be the result of something as simple as power loss without a proper Shutdown operation.
Log-In to the RAID Utilities Figure 44 - RAID Utilities Login Screen To log in to the RAID utilities, perform the following steps. The screen above will appear. • Open the RAID utilities by selecting Start > Raid Status • In the Login menu, click the drop down arrow and select ADMINISTRATOR. • In the Password window, make no entry; leave it blank. In the event this does not work, use the password “3ware”. • Click the Login button to enter the Login Utilities.
Determining the Condition of the RAID Array Figure 45 - RAID Array Condition Screen To check the condition of the array in the RAID Status utility, perform the following steps. The screen above should appear. • Login as ADMINISTRATOR. • Note the Status on this Summary Screen. • If an error condition is indicated continue to next page.
Displaying the Alarm Log of the Raid Array Figure 46 - RAID Alarm Log Screen The RAID controller keeps track of any condition that would adversely affect its reliability. In the event that an error should occur, the alarm log will be helpful in diagnosing the problem. • • Select Monitor > Alarms from the screen. The screen above will appear. Make note of any error conditions reported, and what Port numbers they refer to.
Checking Status of the Drives Figure 47 - RAID Array Maintenance Screen To check the status of the RAID drive array, perform the following steps. The above screen should appear. • Select Management>Maintenance. • Note the status of each drive in the array.
Removing the Degraded Drive from the RAID Unit Figure 48 - Removing Failed Drive from Array The Unit Maintenance screen above will appear. • Remove the degraded drive from the array unit by clicking [Remove Drive]. • Select the Rescan Controller option on the above screen to have the system recognize the drive as Available.
Rebuilding the RAID Array Figure 49 - Selecting a drive to rebuild • Select Rebuild Unit. The dialog above will appear. • Select the available drive by clicking the check box. • Press OK. The RAID array will begin rebuilding with the new drive. This process may take a long time, but the MAXX-2420-EX can still be used. • When complete, OK will be shown in the status for all ports on the Maintenance menu.
RAID Controller Settings The server RAID controller is configured at the factory. The following is provided only to verify these settings and to recreate them if necessary in the event the system is rebuilt. Do not use the Scheduled Events, Email Announcement or Remote Login features. These settings are critical to proper operation of the system.
Multi-Channel Audio Audio Input/Output Modules In addition to embedded audio, provided as a standard feature on the MAXX-2420-EX, an analog audio and a digital audio I/O module are available as optional accessories. Each provides for a total of eight audio channels on XLR-3 connectors, for each video input or output. DXP-1 Digital Audio Module The DXP-2 Digital Audio Module provides 8 audio channels in AES/EBU format, for each video input or output.
DXP-1 Technical Specifications Digital Audio Module Audio channels Audio format Word Size Sampling Frequency Audio connector Data connection to server Audio synchronization Dolby® compatibility Dimensions Weight Power Power supplies Cooling Operating temperature Approvals Country of manufacture 8 per video channel (3 outputs x 8, 1 input x 8) AES/EBU 24-bit 48 kHz XLR-3, gold plated 68-pin x 1-meter cable connects DXP-2 to MAXX-2420-EX Derived from video genlock Bit-for-Bit® reproduction of compressed audi
AXP3/AXP4 Technical Specifications Analog Audio Module Audio channels Word Size Sampling Frequency SNR THD+N Input impedance Output impedance Headroom Audio connector Data connection Dimensions Weight Power Power supplies Cooling Operating temperature Approvals Country of manufacture Page 114 4 per video channel 24-bit 48 kHz > 106 dB A-wtd. Ref to FS –1 dB < .
Maintenance Fault Diagnostics Front Panel Indicators The five LED indicators on the front panel are used to diagnose server fault conditions. The meaning of each indicator is noted in the following table. During normal operation, all five LEDs will be on. GENLOCK OFF indicates that the Genlock setting in the System menu is “Internal” FLASHING indicates that Genlock is selected in the System menu, but there is no signal, or an invalid signal, at the GENLOCK input connector.
Gigabit Ethernet Indicators The Gigabit Network Port card has the following indicator lights: Label Indication ACT/LNK (Left) Green on Green flashing Off The port is connected to a valid link partner Data activity No link Off Green 10 Mb/sec 100 Mb/sec Yellow 1000 Mb/sec 10=OFF 100=GREEN 1000=YELLOW (Right) Meaning Access To Components Be certain to shut down the server and disconnect the power cord before opening the unit for service.
General Handling Precautions ESD Precautions Observe electrostatic discharge (ESD) precautions to avoid damaging static-sensitive components when handling any PC card or disk drive. • • • • • • When the case of your server is open and its internal parts are exposed, do not touch any internal part without first grounding yourself to the chassis. Always wear a ground strap or work on an ESD-protective mat. DO NOT remove components from protective packaging until you are properly grounded.
Program Updates from USB Memory Program updates for the MAXX-2420-EX may be issued from time to time. The server’s operating system and application programs can be updated by the user from a USB Flash Drive distributed by 360 Systems. The current software version is determined by looking in the GUI Help>About dialog box. To install a program update, follow these instructions. Please read them completely before beginning. 1. Discontinue all record, play, network transfer or system-level operations. 2.
Updating Firmware Firmware is low-level code used by the video hardware; it is not server operating system software. If a software update is to be performed as well, install it first unless instructions that came with the software update specifically require loading a particular version of firmware. This procedure must be done from the local GUI; it cannot be done at a Remote Workstation. The following operation should only be undertaken by competent computer technician. To update the firmware: 1.
After each bank is loaded, you should see the message “Verify complete”. The procedure will continue, and finally end with the prompt and cursor: If any of the banks indicate an error during the erase, verify, or programming phases, IMMEDIATELY repeat the operation “loadflash Enter” without doing any other operation. If the procedure still fails, perform the “loadflash Enter” procedure again. Should you still encounter a problem, please contact 360 Systems technical support.
Replacing a Hard Drive Do not remove a hard drive from the server unless the diagnostic software identifies a permanent fault. In that event, the front panel DRIVES LED will blink. Use the hard disk management tools to verify that a drive is at fault. The application monitors many things about the array and individual drives, and will clearly indicate whether a drive has failed. CAUTION: Do not install drives that are not approved by 360 Systems.
Factory Repair Policy A video server being returned under warranty shall be sent to 360 Systems, freight prepaid, in the original or equivalent packaging. Call 360 Systems for a return authorization number before returning a product. Have your serial number and software version number available for reference. Use the following address for shipping and correspondence. 360 Systems’ offices are open Monday through Friday, from 8:30 AM to 5:00 PM, Pacific Time. 360 Systems Customer Service Dept.
FCC Emission Limits This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation. Radio Interference (Canada) English: This Class A digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations.
Product Warranty Limited Warranty This product is warranted to the original purchaser against defects in material and workmanship for a period of one year from the date of original purchase. This warranty covers parts and labor and is effective when the product is used without alteration for the purpose intended by 360 Systems.
End User License Agreement For Server Software IMPORTANT THIS IS A LEGAL AGREEMENT BETWEEN YOU (“YOU”) AND 360 SYSTEMS® (“COMPANY”). COMPANY IS WILLING TO LICENSE THE SERVER SOFTWARE TO YOU ONLY UPON THE CONDITION THAT YOU ACCEPT ALL OF THE TERMS CONTAINED IN THIS SOFTWARE LICENSE AGREEMENT (“AGREEMENT”).
5. Company warrants that the Software will perform substantially in accordance with its Documentation. Your exclusive remedy for breach of this limited warranty and Company’s entire liability shall be, in Company’s discretion, either return of the price paid to Company by You for the Software, or repair or replacement of the Software after Software and Documentation are returned to Company with an applicable receipt.
Appendix A Connector Specifications Audio XLR-3 Connector Pinout Signals appearing on XLR connectors of the DXP-1, AXP-3 or AXP-4 multi-channel audio modules conform to the following wiring standard.
BNC Connectors The following note applies to all video and Genlock connectors: • • A BNC connector used as an output has a 75-ohm source impedance. A BNC connector used as an input has a 75-ohm termination. GPIO Connectors General purpose control inputs (GPI) may be applied to the GPIO connectors, which are DB-25 pin connectors. These inputs are optically isolated from the server circuitry; individual floating returns are provided.
INTERNAL CIRCUITS GPI/O (DB25-F) 1K GPI 1 1 GPI 1 RTN 14 GPI 2 2 GPI 2 RTN 15 GPI 3 3 GPI 3 RTN 16 GPI 4 4 GPI 4 RTN 17 GPI 5 5 GPI 5 RTN 18 GPI 6 6 GPI 6 RTN 19 GPO 1 23 GPO 2 11 GPO 3 24 GPO 4 12 GPO 5 25 GPO 6 13 1K 1K INPUTS 1K 1K 1K OUTPUTS 21 +5V, 200mA MAX SOURCE 22 8 SIGNAL GND 9 10 Figure 31: GPIO Connection Schematic MAXX-2420-EX Owner’s Manual Page 129
System Board Ports Standard computer I/O ports on the server include video monitor, keyboard, mouse, and Gigabit Ethernet. Pinouts are provided to assist in wiring or trouble-shooting. Keyboard and Mouse Keyboard and mouse ports are provided on the rear panel. Both ports are provided with a resetable fuse protecting the +5V supply to the peripheral. SVGA Ports An SVGA computer monitor may be connected to the 15-pin video port.
Appendix B Serial Command Protocols VDCP Command Table The server responds to the following VDCP commands. Shaded areas indicate commands slated for future implementation.
CMD-1 3X CMD-2 01 NAME Open Port CMD-1 3X CMD-2 81 NAME Grant/Denied 3X / BX 02 Next 3X 82 List of ID's 3X 05 Port Status Request 3X 85 State Status 3X 06 Position Request 3X 86 Position 3X / BX 07 Active ID Request 3X 87 Active ID 3X 08 Device Type Req. 3X 88 Device Type 3X 10 Syst.
P2 (BVW) Serial Command Table The server command set includes most BVW-type commands. Commands not implemented include those for DMC operations, audio split and in/out points, and those specifically related to tape as a medium. COMMAND 00.11 00.1D 00.0C 20.00 20.01 20.02 20.10 2X.11 2X.12 2X.13 20.20 2X.21 2X.22 2X.23 20.30 20.0F 20.05 20.60 20.61 24.31 40.08 40.10 40.11 40.18 40.19 40.1A 40.1B 40.2D 41.36 41.37 44.00 44.04 44.31 41.33 N/A 7X.20 N/A 40.48 40.49 6X.
Odetics® Protocol Odetics serial protocol is an extension of P2 machine control protocol. Among its most significant features is the selection of a file by name rather than by time-code location, as with P2. Odetics protocol is used by many table-top controllers and some automation systems. Note that the Odetics protocol only supports clip names up to 8 characters. Longer clip names are automatically filtered out from responses by the server.
COMMAND 0X4X00 DESCRIPTION TIMER1 PRESET RETURN ACK COMMENT 0X4X04 TIME CODE PRESET ACK 0X4008 TIMER1 RESET ACK 0X4010 IN ENTRY ACK 0X4011 OUT ENTRY ACK 0X4X14 IN PRESET ACK 0X4X15 OUT PRESET ACK 0X4018 IN SHIFT PLUS ACK 0X4019 IN SHIFT MINUS ACK 0X401A OUT SHIFT PLUS ACK 0X401B OUT SHIFT MINUS ACK 0X4020 IN RESET ACK 0X4021 OUT RESET ACK 0X402D LOST LOCK RESET ACK 0X4X30 EDIT PRESET ACK 0X4X31 PRE-ROLL TIME PRESET ACK 0X4X32 TAPE AUTO SELECT ACK 0X4X33 S
COMMAND DESCRIPTION GEN UB DATA GEN U BAND TC DATA 0X600C Page 136 RETURN 0X7409 COMMENT 0X7809 CURRENT TIME SENSE CORRECTED LTC TIME DATA 0X7414 VITC TIME DATA 0X7406 TIMER1 DATA 0X7400 HOLD USER BITS LTC DATA 0X7415 HOLD USER BITS VITC DATA 0X7416 0X6010 IN DATA 0X7410 0X6011 OUT DATA 0X7411 0X6012 A IN DATA NAK 0X6013 A OUT DATA NAK 0X6020 STATUS DATA 0X7420 0X6X23 SIGNAL CONTROL DATA 0X7423 0X602E COMMAND SPEED DATA 0X712E 0X602F VAR MEM SPEED DATA 0X712F 0X6X30
Appendix C Technical Specifications Video Video Input Video Outputs HD Input/Output Monitoring Outputs HD Video Formats Video Encoding Jog/Shuttle Slow Motion Play with audio Channel Ganging 2 Channel 4 Channels (2 are bidirectional) HD-SDI, SMPTE 292M Letterboxed composite video (optional) 1080i or 720p at 59.
Keyboard Shortcuts Transport Control Edit Operations L Forward at 4x, 16x, 64x, 128x E Enter/Exit Edit Mode K Pause (Stop) I Capture Mark In J Reverse at 4x, 16x, 64x, 128x O Capture Mark Out Space Bar Play/Pause (toggle) Shift+R Review Edit R Record Shift+T Review Tail Home GoTo Head point End GoTo Tail point Shift+E E/E Toggle Home Recue Shift+L Loop Toggle Space Play/Pause Shift+C Local Toggle K Stop Shift+J Eject Clip Right Arrow Jog forward 1 frame Left Arrow
Appendix D Playlist Management Detail Playlists can be accessed via the server’s FTP feature, allowing several capabilities: • Lists can be backed up on a PC, and sent to another server. • Lists can be viewed and printed from the PC • Lists can be edited or created on the PC and uploaded to the server. Playlists are found on the server FTP directory in the lists folder. They are simple text files with the extension .lst.
Each line of the example appears with its explanation below: #360PLAYLIST 2.0 Header line, this must always be present exactly as shown. #StartTime 13000100 This is the Start Time in military format, hours, minutes, seconds and frames, without leading zeros. This value shows 13:00:01 or 1 minute past 1 pm. The default is 0 which is 12 midnight. While frames are present in this value, the last two digits should always be “00” when entering any value except 0.
Some text editors, such as Notepad, do not display each line separately. Word and Wordpad perform correctly because they accept files that have only Line Feeds (LF) at the ends of lines. The server will accept modified or externally created files with only LF or with both LF and Carriage Return (CR) at line endings. Do not use only CR without LF. A list can be edited by: • Changing the name of a clip: Clip names are case sensitive.
Appendix E As-Run Logging Detail To enable As-Run logs, open a Playlist window, select Options, and then click on As-Run Logs. When enabled, a check mark will appear next to the As-Run log label, and files played by a playlist will be written to an As-Run log. Clips played in a transport window do not get written to an as-run log. As-Run logs are available only through FTP downloads; they cannot be viewed or printed from the server itself. After logging into the server, select the ASRUN folder.
As-Run Log Page Header This section describes the format of the first line (page header): IS-76152 as-run (Ch2:KQRS) Engr Wed Feb 02, 2009 [Wednesday PM] Pg 1 IS-76152: IS-XXXXX, where XXXXX is the unique machine ID as shown in Help>About>Unit ID. as-run (Ch2:KQRS): ChX is the channel number and KQRS is the name of the specific channel, as defined in the Configuration System window. Engr: The name of the server, as defined in the Configuration System window.
Appendix F Mechanical Drawing Figure 32: Dimensional Drawing Page 144 MAXX-2420-EX Owner’s Manual
Index 360 Systems Customer Service ........................................122 E-mail..........................................................122 Fax..............................................................122 Telephone...................................................122 Website ......................................................122 3D Playback......................................................71 Address, 360 Systems ......................................122 AES/EBU............................
Duration Display ...............................................50 DXP-1 Digital Audio Module...........................112 Mounting ......................................................22 DXP-1 Technical Specifications .......................113 Edit Menu..........................................................31 Editing Clip...............................................................49 While Recording ...........................................49 E-E Mode..............................................
Transport View .............................................34 Out Point Display..............................................50 Outputs Time Code ....................................................25 Video......................................................24, 25 P2 Command Table .........................................133 Serial Control ................................................92 Pause ................................................................46 Pinout GPIO ...............................
Take Control .....................................................34 TARGA (.tga) files..............................................80 TARGA File Import............................................72 Tested Remote Control Panels, Switchers ..........97 Tile Windows....................................................31 Time Code LTC...............................................................25 Time Code Source Setting...........................................................42 Top Cover Removing ........
