- 3com Network Interface Card User Guide
Table Of Contents
- About This Guide
- Introduction
- Overview
- 3CR990 NIC Features
- DynamicAccess LAN Agent
- Windows2000 Offload Features
- Installing and Connectingthe NIC
- Installing NICDrivers in Windows
- Installing DynamicAccess Software in Windows
- Overview
- Installing the DynamicAccess LAN Agent for a Client NIC
- Installing DynamicAccess Software for a Server NIC
- Configuring Groups and VLANs for a Server NIC
- Planning the Configuration
- Working With Server Features
- Creating a Group
- Adding NICs to a Group
- Specifying a Dedicated IP Address
- Changing an IP Address
- Creating a VLAN
- Specifying Traffic Priorities
- Saving the Configuration
- Disabling Load Balancing for a Group
- Changing the Primary NIC
- Removing a NIC from a Group
- Deleting or Editing a VLAN
- Displaying NIC Properties
- Displaying Group Properties
- Specifying Failover from Gigabit to 10/100 PCI
- Troubleshooting a Load Balancing Configuration
- Changing Windows2000 Property Settings
- Identifying Windows 2000 Miniport and LAN Connections
- Using Windows2000 Offload Features
- Installing DynamicAccess LAN Encryption Software
- Installing NetWare Client and ServerDrivers
- Overview
- Installing and Configuring the NetWare Server Driver
- Using the Latest Support Packs
- Obtaining NetWare Loadable Modules
- Server Software Installation Requirements
- Installing the NetWare 3.12 Server Driver
- Installing the Server Driver for NetWare 4.11 and 5.0 UsingINETCFG
- Installing the Server Driver and DynamicAccess Technology Using AUTOEXEC.NCF
- Installing Multiple Server NICs
- Verifying the PCI Slot Number
- Installing Server Features
- Configuring Groups
- Verifying the Installation and Configuration
- Changing NetWare Driver Configuration Parameters
- Maintaining Groups
- Configuring the NIC
- Configuring IP Security
- Troubleshooting the NIC
- Running NIC Diagnostics
- Obtaining Drivers
- Specifications and CablingRequirements
- Installing the 3ComDMIAgent
- EtherCD Content and Navigation
- Installing a 3Com NIC While Installing the NOS
- Technical Support
- Index
- FCC Class B Statement
- FCC Declaration of Conformity
- Industry Canada Class B Emission ComplianceStatement
- Avis de Conformité à la Réglementation d’IndustrieCanada
- VCCI Class B Statement
- 3Com End User Software License Agreement
- Product Registration
108 CHAPTER 5: INSTALLING NETWARE CLIENT AND SERVER DRIVERS
Server Feature Commands
DynamicAccess server feature commands for NetWare can
be used to create sophisticated configurations of groups
and for troubleshooting. You can enter them at the
NetWare command line or add them to the appropriate
NCF file. The commands are summarized below.
As shown in the examples, all commands are preceded by
the keyword lbrsl.
group
This command creates groups from specified slot
parameters for primary and secondary NICs.
display status
This command displays information about all groups, or if a
primary slot parameter is specified, only about the specified
group. A separate message is displayed for each loaded
frame type. Board numbers are also displayed. Information
about the relationship between the board numbers and the
frame types is shown in the NetWare 5 Console Monitor.
On the Available Options screen, select LAN/WAN drivers
for this information.
Syntax
lbrsl group lb addr RxIPAddr pri_slot
sec_slot [sec_slot ...]
lbrsl group rsl pri_slot sec_slot
[sec_slot...]
where:
lb specifies a load balancing group.
rsl specifies a resilient server link group.
RxIPAddr is a dedicated IP address for the load balancing
group
pri_slot is the PCI slot number of the primary NIC.
sec_slot is the PCI slot number of a secondary NIC.
Example
lbrsl group lb addr 192.1.1.100 10001
10002
lbrsl group rsl 10001 10002
Default None