- 3com Network Interface Card User Guide
Table Of Contents
- About This Guide
- Introduction
- Overview
- 3CR990 NIC Features
- DynamicAccess LAN Agent
- Windows2000 Offload Features
- Installing and Connectingthe NIC
- Installing NICDrivers in Windows
- Installing DynamicAccess Software in Windows
- Overview
- Installing the DynamicAccess LAN Agent for a Client NIC
- Installing DynamicAccess Software for a Server NIC
- Configuring Groups and VLANs for a Server NIC
- Planning the Configuration
- Working With Server Features
- Creating a Group
- Adding NICs to a Group
- Specifying a Dedicated IP Address
- Changing an IP Address
- Creating a VLAN
- Specifying Traffic Priorities
- Saving the Configuration
- Disabling Load Balancing for a Group
- Changing the Primary NIC
- Removing a NIC from a Group
- Deleting or Editing a VLAN
- Displaying NIC Properties
- Displaying Group Properties
- Specifying Failover from Gigabit to 10/100 PCI
- Troubleshooting a Load Balancing Configuration
- Changing Windows2000 Property Settings
- Identifying Windows 2000 Miniport and LAN Connections
- Using Windows2000 Offload Features
- Installing DynamicAccess LAN Encryption Software
- Installing NetWare Client and ServerDrivers
- Overview
- Installing and Configuring the NetWare Server Driver
- Using the Latest Support Packs
- Obtaining NetWare Loadable Modules
- Server Software Installation Requirements
- Installing the NetWare 3.12 Server Driver
- Installing the Server Driver for NetWare 4.11 and 5.0 UsingINETCFG
- Installing the Server Driver and DynamicAccess Technology Using AUTOEXEC.NCF
- Installing Multiple Server NICs
- Verifying the PCI Slot Number
- Installing Server Features
- Configuring Groups
- Verifying the Installation and Configuration
- Changing NetWare Driver Configuration Parameters
- Maintaining Groups
- Configuring the NIC
- Configuring IP Security
- Troubleshooting the NIC
- Running NIC Diagnostics
- Obtaining Drivers
- Specifications and CablingRequirements
- Installing the 3ComDMIAgent
- EtherCD Content and Navigation
- Installing a 3Com NIC While Installing the NOS
- Technical Support
- Index
- FCC Class B Statement
- FCC Declaration of Conformity
- Industry Canada Class B Emission ComplianceStatement
- Avis de Conformité à la Réglementation d’IndustrieCanada
- VCCI Class B Statement
- 3Com End User Software License Agreement
- Product Registration
Maintaining Groups 109
help
This command displays the syntax for the DynamicAccess
server features commands.
link timeout
When a group is being created, the software waits the
number of seconds specified by this command for the
link/topology check to finish and then displays timeout
information.
probe interval
This command sets the probe packet interval. If no
argument is specified or the specified argument is invalid,
the current value is displayed. Otherwise, the new value
is displayed.
Syntax
lbrsl display status [pri_slot]
where:
pri_slot is the PCI slot number of the primary NIC in the
group for which information is to be displayed. If this
parameter is not specified, information for all groups is
displayed. An example of the type of information
displayed follows:
Group NNN (LB group)
Primary board id: Original NNN, Current NNN
Load balancing on incoming IP packets: Enabled; IP Rx
Addr: NN.NN.NN.NN
Primary node address: XX:XX:XX:XX:XX:XX
Timeout values in seconds: send NNN, receive NNN,
wait NNN, link NNN
Probe Interval: NNN seconds
Slot number NNN (Active), Node Address:
XXX:XXX:XXX:XXX:XXX:XXX
Example
lbrsl display status 10001
Syntax
lbrsl help
Syntax
lbrsl link timeout seconds
where:
seconds is the time in seconds.
Example
lbrsl link timeout 10
Default 5