- 3com Network Interface Card User Guide
Table Of Contents
- About This Guide
- Introduction
- Overview
- 3CR990 NIC Features
- DynamicAccess LAN Agent
- Windows2000 Offload Features
- Installing and Connectingthe NIC
- Installing NICDrivers in Windows
- Installing DynamicAccess Software in Windows
- Overview
- Installing the DynamicAccess LAN Agent for a Client NIC
- Installing DynamicAccess Software for a Server NIC
- Configuring Groups and VLANs for a Server NIC
- Planning the Configuration
- Working With Server Features
- Creating a Group
- Adding NICs to a Group
- Specifying a Dedicated IP Address
- Changing an IP Address
- Creating a VLAN
- Specifying Traffic Priorities
- Saving the Configuration
- Disabling Load Balancing for a Group
- Changing the Primary NIC
- Removing a NIC from a Group
- Deleting or Editing a VLAN
- Displaying NIC Properties
- Displaying Group Properties
- Specifying Failover from Gigabit to 10/100 PCI
- Troubleshooting a Load Balancing Configuration
- Changing Windows2000 Property Settings
- Identifying Windows 2000 Miniport and LAN Connections
- Using Windows2000 Offload Features
- Installing DynamicAccess LAN Encryption Software
- Installing NetWare Client and ServerDrivers
- Overview
- Installing and Configuring the NetWare Server Driver
- Using the Latest Support Packs
- Obtaining NetWare Loadable Modules
- Server Software Installation Requirements
- Installing the NetWare 3.12 Server Driver
- Installing the Server Driver for NetWare 4.11 and 5.0 UsingINETCFG
- Installing the Server Driver and DynamicAccess Technology Using AUTOEXEC.NCF
- Installing Multiple Server NICs
- Verifying the PCI Slot Number
- Installing Server Features
- Configuring Groups
- Verifying the Installation and Configuration
- Changing NetWare Driver Configuration Parameters
- Maintaining Groups
- Configuring the NIC
- Configuring IP Security
- Troubleshooting the NIC
- Running NIC Diagnostics
- Obtaining Drivers
- Specifications and CablingRequirements
- Installing the 3ComDMIAgent
- EtherCD Content and Navigation
- Installing a 3Com NIC While Installing the NOS
- Technical Support
- Index
- FCC Class B Statement
- FCC Declaration of Conformity
- Industry Canada Class B Emission ComplianceStatement
- Avis de Conformité à la Réglementation d’IndustrieCanada
- VCCI Class B Statement
- 3Com End User Software License Agreement
- Product Registration
Installing the Network Driver Using the EtherCD 43
Refer to your system administrator or the Windows NT
documentation for assistance. After entering the
appropriate TCP/IP information and clicking OK, the
Network Settings Change window appears.
If the Microsoft TCP/IP Properties screen does not appear,
the installation is complete. The Network Settings Change
window appears.
14 Click Yes to restart the PC.
The network driver installation is complete. Go to Verifying
Successful Installation on page 48 to confirm that the NIC
is properly installed.
Windows 98
This section describes how to install the network driver and
NIC software in a PC or server running Windows 98.
Before installing the NIC software:
■ Make sure that the NIC is installed in the PC and
connected to the network.
■ Make sure that you have the Windows 98 installation
files. These files may be on a CD or diskettes, or they
may have been copied to your hard disk when
Windows 98 was installed on your PC.
To install the software:
1 Turn the PC power on.
Windows detects the NIC. The Add New Hardware Wizard
starts.
2 Click Next.
The Add New Hardware Wizard screen prompts you to
select an option.
3 Select the Search for the best driver for your device
(Recommended) option, and then click Next.
The Add New Hardware Wizard screen prompts you for the
driver location.
If you encounter problems during the installation, see
TROUBLE.TXT (located in the HELP directory on the
EtherCD) for troubleshooting tips.