- 3com Network Interface Card User Guide
Table Of Contents
- About This Guide
- Introduction
- Overview
- 3CR990 NIC Features
- DynamicAccess LAN Agent
- Windows2000 Offload Features
- Installing and Connectingthe NIC
- Installing NICDrivers in Windows
- Installing DynamicAccess Software in Windows
- Overview
- Installing the DynamicAccess LAN Agent for a Client NIC
- Installing DynamicAccess Software for a Server NIC
- Configuring Groups and VLANs for a Server NIC
- Planning the Configuration
- Working With Server Features
- Creating a Group
- Adding NICs to a Group
- Specifying a Dedicated IP Address
- Changing an IP Address
- Creating a VLAN
- Specifying Traffic Priorities
- Saving the Configuration
- Disabling Load Balancing for a Group
- Changing the Primary NIC
- Removing a NIC from a Group
- Deleting or Editing a VLAN
- Displaying NIC Properties
- Displaying Group Properties
- Specifying Failover from Gigabit to 10/100 PCI
- Troubleshooting a Load Balancing Configuration
- Changing Windows2000 Property Settings
- Identifying Windows 2000 Miniport and LAN Connections
- Using Windows2000 Offload Features
- Installing DynamicAccess LAN Encryption Software
- Installing NetWare Client and ServerDrivers
- Overview
- Installing and Configuring the NetWare Server Driver
- Using the Latest Support Packs
- Obtaining NetWare Loadable Modules
- Server Software Installation Requirements
- Installing the NetWare 3.12 Server Driver
- Installing the Server Driver for NetWare 4.11 and 5.0 UsingINETCFG
- Installing the Server Driver and DynamicAccess Technology Using AUTOEXEC.NCF
- Installing Multiple Server NICs
- Verifying the PCI Slot Number
- Installing Server Features
- Configuring Groups
- Verifying the Installation and Configuration
- Changing NetWare Driver Configuration Parameters
- Maintaining Groups
- Configuring the NIC
- Configuring IP Security
- Troubleshooting the NIC
- Running NIC Diagnostics
- Obtaining Drivers
- Specifications and CablingRequirements
- Installing the 3ComDMIAgent
- EtherCD Content and Navigation
- Installing a 3Com NIC While Installing the NOS
- Technical Support
- Index
- FCC Class B Statement
- FCC Declaration of Conformity
- Industry Canada Class B Emission ComplianceStatement
- Avis de Conformité à la Réglementation d’IndustrieCanada
- VCCI Class B Statement
- 3Com End User Software License Agreement
- Product Registration
![](/manual/3com/3cr990svr95/3com-network-interface-card-user-guide/images/img-50.png)
50 CHAPTER 3: INSTALLING NIC DRIVERS IN WINDOWS
3 Double-click Network adapters and make sure that
the name of the 3Com EtherLink NIC appears.
If a red X or a yellow exclamation point (!) appears by the
name of the NIC, the installation was not successful. See
Troubleshooting the NIC Installation on page 132 for
troubleshooting help.
Installing the 3Com NIC Diagnostics Program
This section describes how to install the 3Com NIC
Diagnostics program after you have already installed
the network driver. This program is for PCs running
Windows 2000, Windows NT 4.0, Windows 98, or
Windows 95.
The 3Com NIC Diagnostics program allows you to run tests
that determine the status of your network and the NIC.
It also allows you to configure the NIC, view network
statistics and LEDs, and access support databases.
To install the 3Com NIC Diagnostics program:
1 Turn on the power to the PC and start Windows.
2 Insert the EtherCD in the CD-ROM drive.
The EtherCD Welcome screen appears.
3 Click NIC Software.
4 Click NIC Drivers and Diagnostics.
5 Click Update NIC Driver.
6 Click Update Drivers and Diagnostic Program.
The Update screen appears, displaying a message
indicating the 3Com NIC Update Kit has successfully
updated the network software, and informing you that
you must restart your PC.
7 Click OK to return to the Update NIC drivers screen,
and then exit the EtherCD.
When you install the 3Com NIC Diagnostics program, the
network driver is automatically updated to the
latest version on the EtherCD.