- 3com Network Interface Card User Guide
Table Of Contents
- About This Guide
- Introduction
- Overview
- 3CR990 NIC Features
- DynamicAccess LAN Agent
- Windows2000 Offload Features
- Installing and Connectingthe NIC
- Installing NICDrivers in Windows
- Installing DynamicAccess Software in Windows
- Overview
- Installing the DynamicAccess LAN Agent for a Client NIC
- Installing DynamicAccess Software for a Server NIC
- Configuring Groups and VLANs for a Server NIC
- Planning the Configuration
- Working With Server Features
- Creating a Group
- Adding NICs to a Group
- Specifying a Dedicated IP Address
- Changing an IP Address
- Creating a VLAN
- Specifying Traffic Priorities
- Saving the Configuration
- Disabling Load Balancing for a Group
- Changing the Primary NIC
- Removing a NIC from a Group
- Deleting or Editing a VLAN
- Displaying NIC Properties
- Displaying Group Properties
- Specifying Failover from Gigabit to 10/100 PCI
- Troubleshooting a Load Balancing Configuration
- Changing Windows2000 Property Settings
- Identifying Windows 2000 Miniport and LAN Connections
- Using Windows2000 Offload Features
- Installing DynamicAccess LAN Encryption Software
- Installing NetWare Client and ServerDrivers
- Overview
- Installing and Configuring the NetWare Server Driver
- Using the Latest Support Packs
- Obtaining NetWare Loadable Modules
- Server Software Installation Requirements
- Installing the NetWare 3.12 Server Driver
- Installing the Server Driver for NetWare 4.11 and 5.0 UsingINETCFG
- Installing the Server Driver and DynamicAccess Technology Using AUTOEXEC.NCF
- Installing Multiple Server NICs
- Verifying the PCI Slot Number
- Installing Server Features
- Configuring Groups
- Verifying the Installation and Configuration
- Changing NetWare Driver Configuration Parameters
- Maintaining Groups
- Configuring the NIC
- Configuring IP Security
- Troubleshooting the NIC
- Running NIC Diagnostics
- Obtaining Drivers
- Specifications and CablingRequirements
- Installing the 3ComDMIAgent
- EtherCD Content and Navigation
- Installing a 3Com NIC While Installing the NOS
- Technical Support
- Index
- FCC Class B Statement
- FCC Declaration of Conformity
- Industry Canada Class B Emission ComplianceStatement
- Avis de Conformité à la Réglementation d’IndustrieCanada
- VCCI Class B Statement
- 3Com End User Software License Agreement
- Product Registration
![](/manual/3com/3cr990svr95/3com-network-interface-card-user-guide/images/img-56.png)
56 CHAPTER 4: INSTALLING DYNAMICACCESS SOFTWARE IN WINDOWS
The following table lists the minimum client requirements
and recommended Microsoft Service Packs (if any) for the
version of the DynamicAccess LAN agent that is included
on the EtherCD.
Installing the LAN Agent
To install the DynamicAccess LAN agent:
1 Make sure that the NIC and the network driver are
installed on your PC.
See Verifying Successful Installation on page 48 to confirm
that the NIC is properly installed in the computer.
2 Start Windows.
3 Insert the EtherCD in the CD-ROM drive.
The EtherCD Welcome screen appears.
4 Click NIC Software.
5 Click DynamicAccess Technology.
6 Click Install DynamicAccess Technology.
7 Select the appropriate menu option for your
operating system (Windows 95/98 or
Windows NT 4.0)
Operating
System
Requirements for Running
DynamicAccess Technology
on a Client PC
Recommended
Microsoft
Service Pack
Windows 2000 486/66 MHz CPU
32 MB RAM
5 MB available hard drive space
None required
Windows NT 4.0 Pentium/100 MHz CPU
32 MB RAM
5 MB available hard drive space
Service Pack 6
(or later)
Windows 98 486/76 MHz CPU
32 MB RAM
5 MB available hard drive space
Service Pack 1
Windows 95 486/76 MHz CPU
32 MB RAM
5 MB available hard drive space
Windows 95 OSR2 or
Service Pack 1
Ignore the Windows 2000 menu option. The
DynamicAccess LAN agent is not supported on a PC
running Windows 2000.