- 3com Network Interface Card User Guide
Table Of Contents
- About This Guide
- Introduction
- Overview
- 3CR990 NIC Features
- DynamicAccess LAN Agent
- Windows2000 Offload Features
- Installing and Connectingthe NIC
- Installing NICDrivers in Windows
- Installing DynamicAccess Software in Windows
- Overview
- Installing the DynamicAccess LAN Agent for a Client NIC
- Installing DynamicAccess Software for a Server NIC
- Configuring Groups and VLANs for a Server NIC
- Planning the Configuration
- Working With Server Features
- Creating a Group
- Adding NICs to a Group
- Specifying a Dedicated IP Address
- Changing an IP Address
- Creating a VLAN
- Specifying Traffic Priorities
- Saving the Configuration
- Disabling Load Balancing for a Group
- Changing the Primary NIC
- Removing a NIC from a Group
- Deleting or Editing a VLAN
- Displaying NIC Properties
- Displaying Group Properties
- Specifying Failover from Gigabit to 10/100 PCI
- Troubleshooting a Load Balancing Configuration
- Changing Windows2000 Property Settings
- Identifying Windows 2000 Miniport and LAN Connections
- Using Windows2000 Offload Features
- Installing DynamicAccess LAN Encryption Software
- Installing NetWare Client and ServerDrivers
- Overview
- Installing and Configuring the NetWare Server Driver
- Using the Latest Support Packs
- Obtaining NetWare Loadable Modules
- Server Software Installation Requirements
- Installing the NetWare 3.12 Server Driver
- Installing the Server Driver for NetWare 4.11 and 5.0 UsingINETCFG
- Installing the Server Driver and DynamicAccess Technology Using AUTOEXEC.NCF
- Installing Multiple Server NICs
- Verifying the PCI Slot Number
- Installing Server Features
- Configuring Groups
- Verifying the Installation and Configuration
- Changing NetWare Driver Configuration Parameters
- Maintaining Groups
- Configuring the NIC
- Configuring IP Security
- Troubleshooting the NIC
- Running NIC Diagnostics
- Obtaining Drivers
- Specifications and CablingRequirements
- Installing the 3ComDMIAgent
- EtherCD Content and Navigation
- Installing a 3Com NIC While Installing the NOS
- Technical Support
- Index
- FCC Class B Statement
- FCC Declaration of Conformity
- Industry Canada Class B Emission ComplianceStatement
- Avis de Conformité à la Réglementation d’IndustrieCanada
- VCCI Class B Statement
- 3Com End User Software License Agreement
- Product Registration
80 CHAPTER 4: INSTALLING DYNAMICACCESS SOFTWARE IN WINDOWS
13 Verify that the displayed components are correct for
installation on your computer and click Next.
The system copies files from the EtherCD to the destination
location, sets up the registry, builds drivers, and updates
bindings.
The Winsock2 Setup screen appears.
Follow the rest of the setup wizard instructions to install
the software properly. If you see “version conflict”
messages, click Cancel to continue. When prompted to
reboot, click Yes (or OK or Next) to continue.
If you see “Winsock 2 setup” error messages, reboot the
system and re-start the 3Com LAN Encryption installation.
If prompted to insert the Windows CD, insert it so that
certain Windows files can be copied. (Prompting for the
Windows CD depends on your PC configuration.) Follow
the displayed prompts.
14 With the Winsock2 Setup screen displayed, click OK.
A warning message appears regarding the Dial-Up
Networking Upgrade.
15 Click OK.
The Microsoft Dial-Up Networking screen appears,
prompting you to restart.
16 Click Yes.
A message appears.
17 Click Yes.
A warning message appears, informing you that you must
restart and then manually run the installation process again.
18 Click OK.
The computer will restart.
19 Enter your network password when prompted.
The setup wizard continues to build drivers. The Insert Disk
screen appears, prompting you to insert the Windows 95
CD-ROM.