- 3com Network Interface Card User Guide
Table Of Contents
- About This Guide
- Introduction
- Overview
- 3CR990 NIC Features
- DynamicAccess LAN Agent
- Windows2000 Offload Features
- Installing and Connectingthe NIC
- Installing NICDrivers in Windows
- Installing DynamicAccess Software in Windows
- Overview
- Installing the DynamicAccess LAN Agent for a Client NIC
- Installing DynamicAccess Software for a Server NIC
- Configuring Groups and VLANs for a Server NIC
- Planning the Configuration
- Working With Server Features
- Creating a Group
- Adding NICs to a Group
- Specifying a Dedicated IP Address
- Changing an IP Address
- Creating a VLAN
- Specifying Traffic Priorities
- Saving the Configuration
- Disabling Load Balancing for a Group
- Changing the Primary NIC
- Removing a NIC from a Group
- Deleting or Editing a VLAN
- Displaying NIC Properties
- Displaying Group Properties
- Specifying Failover from Gigabit to 10/100 PCI
- Troubleshooting a Load Balancing Configuration
- Changing Windows2000 Property Settings
- Identifying Windows 2000 Miniport and LAN Connections
- Using Windows2000 Offload Features
- Installing DynamicAccess LAN Encryption Software
- Installing NetWare Client and ServerDrivers
- Overview
- Installing and Configuring the NetWare Server Driver
- Using the Latest Support Packs
- Obtaining NetWare Loadable Modules
- Server Software Installation Requirements
- Installing the NetWare 3.12 Server Driver
- Installing the Server Driver for NetWare 4.11 and 5.0 UsingINETCFG
- Installing the Server Driver and DynamicAccess Technology Using AUTOEXEC.NCF
- Installing Multiple Server NICs
- Verifying the PCI Slot Number
- Installing Server Features
- Configuring Groups
- Verifying the Installation and Configuration
- Changing NetWare Driver Configuration Parameters
- Maintaining Groups
- Configuring the NIC
- Configuring IP Security
- Troubleshooting the NIC
- Running NIC Diagnostics
- Obtaining Drivers
- Specifications and CablingRequirements
- Installing the 3ComDMIAgent
- EtherCD Content and Navigation
- Installing a 3Com NIC While Installing the NOS
- Technical Support
- Index
- FCC Class B Statement
- FCC Declaration of Conformity
- Industry Canada Class B Emission ComplianceStatement
- Avis de Conformité à la Réglementation d’IndustrieCanada
- VCCI Class B Statement
- 3Com End User Software License Agreement
- Product Registration
![](/manual/3com/3cr990svr95/3com-network-interface-card-user-guide/images/img-92.png)
Installing and Configuring the NetWare Server Driver 93
The NLM file location is typically in the sys:system directory.
You need a NetWare client system to copy the NLM files to
the server.
2 Copy the LAN driver file (3C99X.LAN) from the
EtherCD to the same directory.
3 Add the following two lines to the AUTOEXEC.NCF file:
load sys:\system\3c99x.lan slot=<slot>
NAME=<name> FRAME=<frametype>
bind ipx to <name> net=<number>
4 Save and exit the file, and then reboot the server.
Installing the Server Driver for NetWare 4.11 and 5.0
Using INETCFG
To install the driver in a NetWare 4.11or 5.0 server:
1 Copy the MSM.NLM, ETHERTSM.NLM, and NBI.NLM
files from the \NWSERVER directory on the EtherCD
to the directory on your hard drive where other NLM
files are located.
The NLM file location is typically in the sys:system directory.
You need a NetWare client system to copy the NLM files to
the server.
2 Insert installation diskette 2 in drive A.
3 At the server prompt, type:
load inetcfg
If you copy the NLM files to a different directory, you must
specify the path in the preceding LOAD statement.
Copy the NLM files only if the versions existing on the
server are older than the versions supplied on the
EtherCD.
CAUTION: You can configure load balancing only
through the command line interface or by manually
updating the AUTOEXEC.NCF file. You cannot have load
balancing automatically configured by INETCFG.SYS.