- 3com Network Interface Card User Guide
Table Of Contents
- About This Guide
- Introduction
- Overview
- 3CR990 NIC Features
- DynamicAccess LAN Agent
- Windows2000 Offload Features
- Installing and Connectingthe NIC
- Installing NICDrivers in Windows
- Installing DynamicAccess Software in Windows
- Overview
- Installing the DynamicAccess LAN Agent for a Client NIC
- Installing DynamicAccess Software for a Server NIC
- Configuring Groups and VLANs for a Server NIC
- Planning the Configuration
- Working With Server Features
- Creating a Group
- Adding NICs to a Group
- Specifying a Dedicated IP Address
- Changing an IP Address
- Creating a VLAN
- Specifying Traffic Priorities
- Saving the Configuration
- Disabling Load Balancing for a Group
- Changing the Primary NIC
- Removing a NIC from a Group
- Deleting or Editing a VLAN
- Displaying NIC Properties
- Displaying Group Properties
- Specifying Failover from Gigabit to 10/100 PCI
- Troubleshooting a Load Balancing Configuration
- Changing Windows2000 Property Settings
- Identifying Windows 2000 Miniport and LAN Connections
- Using Windows2000 Offload Features
- Installing DynamicAccess LAN Encryption Software
- Installing NetWare Client and ServerDrivers
- Overview
- Installing and Configuring the NetWare Server Driver
- Using the Latest Support Packs
- Obtaining NetWare Loadable Modules
- Server Software Installation Requirements
- Installing the NetWare 3.12 Server Driver
- Installing the Server Driver for NetWare 4.11 and 5.0 UsingINETCFG
- Installing the Server Driver and DynamicAccess Technology Using AUTOEXEC.NCF
- Installing Multiple Server NICs
- Verifying the PCI Slot Number
- Installing Server Features
- Configuring Groups
- Verifying the Installation and Configuration
- Changing NetWare Driver Configuration Parameters
- Maintaining Groups
- Configuring the NIC
- Configuring IP Security
- Troubleshooting the NIC
- Running NIC Diagnostics
- Obtaining Drivers
- Specifications and CablingRequirements
- Installing the 3ComDMIAgent
- EtherCD Content and Navigation
- Installing a 3Com NIC While Installing the NOS
- Technical Support
- Index
- FCC Class B Statement
- FCC Declaration of Conformity
- Industry Canada Class B Emission ComplianceStatement
- Avis de Conformité à la Réglementation d’IndustrieCanada
- VCCI Class B Statement
- 3Com End User Software License Agreement
- Product Registration
![](/manual/3com/3cr990svr95/3com-network-interface-card-user-guide/images/img-97.png)
98 CHAPTER 5: INSTALLING NETWARE CLIENT AND SERVER DRIVERS
Installing Multiple Server NICs
To support more than one NIC in a NetWare server, change
the AUTOEXEC.NCF file to the following format:
load 3C99X.LAN slot=<slot1> NAME=<name1>
FRAME=<frametype1>
bind ipx to <name1> net=<net1>
load 3C99X.LAN slot=<slot2> NAME=<name2>
FRAME=<frametype2>
bind ipx to <name2> net=<net2>
The values <slot1> and <slot2> are the numbers of
the PCI slots in which the NICs are physically installed.
To view the numbers of these PCI slots, use the
3Com Configuration and Diagnostic program for DOS.
See Verifying the PCI Slot Number on page 99
for instructions.
The values <name1> and <name2> are unique names
assigned to each NIC by your system administrator. The
values <name1> and <name 2> must be different.
The frame parameters <frametype1> and <frametype2>
can be one of the following:
■ Ethernet_802.2
■ Ethernet_802.3
■ Ethernet_II
■ Ethernet_SNAP
Make sure that the frametype for the server and the
workstation is the same. For example, if the server
uses Ethernet_802.2, the workstation must also use
Ethernet_802.2.
The values <net1> and <net2> are unique numbers
assigned by the system administrator to each NIC. Make
sure that <net1> and <net2> are different numbers.
See the appropriate Novell NetWare manuals for
further information.