3Com 11a/b/g Wireless Workgroup Bridge User Guide Model: WL-560 3CRWE675075 http://www.3com.com/ Part No. DUA6750-75AAA01 Published November 2004 Version 1.0.
3Com Corporation 350 Campus Drive Marlborough MA USA 01752-3064 Copyright © 2004, 3Com Corporation. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation, or adaptation) without written permission from 3Com Corporation.
CONTENTS ABOUT THIS GUIDE Conventions 2 Related Documentation 2 Accessing Online Documentation Product Registration and Support 1 3 4 INTRODUCTION Product Features 5 Security 5 Wireless Network Standards 6 Network Configuration and Planning Example Configurations 8 2 7 INSTALLING THE BRIDGE Unpacking the Bridge 9 Observing Safety Precautions 10 Deciding Where to Place the Bridge 11 Wall-Mounting the Bridge 11 Installing the Locking Bar 12 Placing the Bridge on a Flat Surface 13 Connecting the Bridge 1
3 CONFIGURING THE BRIDGE Using Secure Web Server Connection 23 Using the 3Com Wireless Infrastructure Device Manager 24 Using the Configuration Management System 27 Clearing and Applying System Configuration Settings 28 Changing System Properties 29 Setting IP Network Properties 30 Setting Wireless Network Properties 31 Manually Select Radio Channels 33 Setting Up an Ad-Hoc Network 34 Changing Wireless Security Settings 35 Changing RADIUS Settings 37 Changing SNMP Settings 38 Using the Access Control List
A OBTAINING SUPPORT FOR YOUR 3COM PRODUCT Register Your Product to Gain Service Benefits 53 Solve Problems Online 53 Purchase Extended Warranty and Professional Services Access Software Downloads 54 Contact Us 54 Telephone Technical Support and Repair 55 END USER LICENSE AGREEMENT REGULATORY INFORMATION 54
ABOUT THIS GUIDE This guide provides all the information you need to install and use the 3Com 11a/b/g Wireless Workgroup Bridge in its default state. The guide is intended for use by IT managers and experienced network installation and administration professionals who have a basic knowledge of current networking concepts. If the information in the release notes that are shipped with your product differ from the information in this guide, follow the instructions in the release notes.
2 ABOUT THIS GUIDE Conventions Table 1 and Table 2 list conventions that are used throughout this guide. Table 1 Notice Icons Icon Notice Type Description Information note Information that describes important features or instructions. Caution Information that alerts you to potential loss of data or potential damage to an application, system, or device. Warning Information that alerts you to potential personal injury.
Accessing Online Documentation Accessing Online Documentation 3 ■ Quick Start Guide—printed guide that describes basic installation. ■ Online Help—product help systems that describe how to use the Configuration Management System and 3Com Wireless Infrastructure Device Manager. ■ Release Note—printed note that describes important product information. ■ README.TXT file—text file located on the 3Com Installation CD that describes last-minute product information.
4 ABOUT THIS GUIDE Product Registration and Support To register your product with 3Com, go to the following Web page: http://esupport.3com.com For support information, see “Obtaining Support for your 3Com Product” on page 53 or log on to the 3Com Web site at http://www.3com.com and navigate to the product support page.
1 INTRODUCTION 3Com wireless technology has all of the benefits of a local area network (LAN) without the constraints and expense of network wiring. 3Com 11a/b/g Wireless LAN products provide easy, affordable, flexible ways to extend wireless networks to more users. This guide shows how you can use the 3Com 11a/b/g Wireless Workgroup Bridge in your office or classroom to connect groups of wired Ethernet client devices to your wireless LAN.
6 CHAPTER 1: INTRODUCTION Wireless Network Standards Understanding the characteristics of the 802.11a and 802.11g standards can help you make the best choice for your wireless implementation plans. 802.11a Ratified in 2002, 802.11a is IEEE’s more recent wireless standard. It operates at the 5 GHz band and supports data rates at up to 54 Mbps. Because there are fewer devices in the 5 GHz band, there’s less potential for RF interference.
Network Configuration and Planning 7 Consider 802.11g when you need wider coverage and vendor compatibility and you are: Network Configuration and Planning ■ Maintaining support for existing 802.11b users and the existing wireless investment while providing for expansion into 802.11g. ■ Implementing a complete wireless LAN solution, including bridges, gateways, access points and clients; Wi-Fi certification guarantees compatibility among vendors.
8 CHAPTER 1: INTRODUCTION Example Configurations The following examples illustrate ways you can use the Bridge to configure Ethernet client devices into workgroups. (Details for setting up specific configurations are in “Installing the Bridge” on page 9.) Wireless Infrastructure Network You can connect several computers, including those with non-Windows operating systems, and network printers, as shown in Figure 1.
2 INSTALLING THE BRIDGE This chapter contains the information you need to install and set up the Bridge.
10 CHAPTER 2: INSTALLING THE BRIDGE Figure 3 shows the front view of the Bridge, including the LEDs and connecting ports. It also shows the cradle, which is used to mount the Bridge to a wall or to install the Bridge on a flat surface. Figure 3 Bridge 11a/b/g Wireless Workgroup Bridge Pow er Port Serial Port Ethernet Port Cradle Observing Safety Precautions This equipment must be installed in compliance with local and national building codes, regulatory restrictions, and FCC rules.
Deciding Where to Place the Bridge Deciding Where to Place the Bridge 11 Place the Bridge in a dry, clean location near the hub, computer, or printer that will be connected to the Bridge. The location must have a power source and be within the following distance of a Wi-Fi compliant wireless LAN access point or ad-hoc wireless station: ■ For 802.11a compatibility, place the Bridge within 50 m (164 ft) of a Wi-Fi compliant wireless LAN access point. ■ For 802.
12 CHAPTER 2: INSTALLING THE BRIDGE 2 Route the power and Ethernet cables through the large opening in the cradle. Figure 5 shows a cable being routed under the cradle. Figure 5 Routing Cable Under the Cradle 3 Connect the power and Ethernet cables to the ports on the Bridge. 4 Snap the Bridge onto the cradle. Installing the Locking Bar For additional security, install the locking bar in the cradle after the Bridge is mounted to the wall. Use your own lock to secure it in place.
Deciding Where to Place the Bridge 13 2 Push the locking bar through the opening until the hole on the locking bar is exposed. 3 Insert a lock through the hole on the locking bar, and then close the lock to secure it in place, as shown in Figure 7. .11a .11g .100 .10 Figure 7 Securing the Locking Bar Placing the Bridge on a Flat Surface The Bridge comes with four rubber feet that can be used to install the Bridge on a flat surface such as a table or desktop.
14 CHAPTER 2: INSTALLING THE BRIDGE Connecting the Bridge The Bridge has power, Ethernet, and serial ports, as shown in Figure 8. Before connecting the Bridge to an Ethernet device, connect the power. Figure 8 Connecting the Power Power Cable Ethernet Cable Connecting to a Serial Device The Bridge can also be connected to a serial device, as shown in Figure 9. Serial cables come with a variety of connector sizes.
Connecting the Bridge Connecting to an Ethernet Device 15 The Bridge is designed to be connected to an Ethernet client device such as a hub, computer, or printer. CAUTION: To avoid the possibility of a transmission loop situation between the Bridge and an access point, which could disrupt network operation, do not connect a Bridge that is set in Wireless Client (Infrastructure) mode directly to the LAN (for example, through a wall port or through a hub that is connected directly to the LAN).
16 CHAPTER 2: INSTALLING THE BRIDGE Connecting to a Network Printer You can connect a network printer directly to the Bridge or to a hub that is connected to the Bridge. Used this way, the Bridge allows you to place network printers in areas that are not wired for Ethernet. 1 Configure the network printer as you would for connecting it to the wired LAN. For details on configuring the printer, see your printer documentation. 2 If necessary, configure the Bridge to associate with your access point.
Checking the LED Indicators When the Bridge is connected to power, LEDs indicate activity as follows: a .1 1b .1 /g 00 .1 0 Figure 13 LED Indicators .1 1 Checking the LED Indicators 17 Table 3 LED Descriptions LED Color Indicates Power Green The Bridge is powered up and operating normally. Off The Bridge is not receiving power or there is a fault with the power supply. Green (solid) The Bridge has an 802.11a 5 GHz radio band connection.
18 CHAPTER 2: INSTALLING THE BRIDGE Attaching An External Antenna The Bridge has two internal diversity dual-band antennas. If you want to increase the range of the Bridge, an external antenna can be attached to the external antenna connector on the Bridge. The 3Com-approved external antenna for this Bridge is the 3Com 2.4/5 GHz Omnidirectional Workgroup Bridge Antenna (3CWE501). For more information, go to www.3Com.
Determining if you Need to Configure the Bridge 19 Networks without a DHCP Server If your network does not have a DHCP server, the Bridge uses a default IP address (169.254.2.2) that is assigned at the factory. You can use that IP address to configure the Bridge, or you can assign a new IP address to the Bridge. To verify that the Bridge is using the default IP address assigned at the factory: 1 Connect a computer directly to the Bridge using the supplied standard Category 5 UTP Ethernet cable.
20 CHAPTER 2: INSTALLING THE BRIDGE Bridge Default Settings Table 4 shows the Bridge configuration factory defaults. Table 4 Factory Default Settings Property Default Setting Device Name 3Com WWB Device Location None (blank) Country For U.S. version, United States and Canada For non-U.S. version, set by the user Client Mode Support multiple wired Ethernet clients IP Network Setting Obtain IP address automatically IP Address Obtained automatically (with a DHCP server) 169.254.2.
Using the 3Com Installation CD Using the 3Com Installation CD 21 The 3Com Installation CD contains the following tools and utilities: ■ 3Com Wireless Infrastructure Device Manager—an administration tool that helps you select 3Com wireless LAN devices and launch their configurations in your Web browser. ■ 3Com 3CDaemon Server Tool—a firmware upgrade tool that can act in four different capacities: ■ As a TFTP Server, used for firmware upgrades as well as backup and restore functions.
22 CHAPTER 2: INSTALLING THE BRIDGE To install one of the tools on your computer: 1 Turn on the computer. 2 Insert the 3Com Installation CD in the CD-ROM drive. The setup menu appears. If it does not appear, you can start the setup menu from the Windows Start menu. For example: Start > Run > d:setup.exe. 3 In the menu, click Tools and Utilities. 4 In the next screen, click the tool you want to install. 5 Follow the instructions on the screens to complete the installation.
3 CONFIGURING THE BRIDGE If the Bridge configuration that was set at the factory does not meet your network requirements, or if you want to customize the settings, you can use these tools to change the configuration: Table 6 Configuration Tools Configuration Tool Description 3Com Wireless Infrastructure Device Manager (Widman) Helps you locate 3Com wireless LAN devices on the network, select a device and view its properties, and launch the device’s configuration in your Web browser.
24 CHAPTER 3: CONFIGURING THE BRIDGE Using the 3Com Wireless Infrastructure Device Manager The 3Com Wireless Infrastructure Device Manager (Widman) helps you locate 3Com wireless LAN devices on the network, select a device and view its properties, and launch the Configuration Management System in your Web browser. The Wireless Infrastructure Device Manager must be installed on a computer that: ■ Has a working Ethernet adapter.
Using the 3Com Wireless Infrastructure Device Manager 25 Devices in a different subnet than your computer are identified with exclamation points (!). You can refresh this display by clicking Refresh. You should refresh the display, for example, after you change a device IP address. Figure 14 Wireless Infrastructure Device Manager Wireless Network Tree 2 In the Wireless Network Tree, select the device you want to configure.
26 CHAPTER 3: CONFIGURING THE BRIDGE Figure 15 Wireless Infrastructure Device Manager Pre-IP Configuration 4 The next window prompts for an administrative password to allow the new IP address to be set. If this is the first time the device is being configured, leave the password field blank and click Next. The configuration main page appears in your Web browser. See “Using the Configuration Management System” on page 27 for details.
Using the Configuration Management System Using the Configuration Management System 27 The 3Com11a/b/g Wireless Workgroup Bridge Configuration Management System resides on the Bridge and lets you configure the Bridge through your Web browser. To use the Configuration Management System, the computer you are using to connect to the Bridge must be located on the same subnet as the Bridge.
28 CHAPTER 3: CONFIGURING THE BRIDGE Table 8 Connection Status Page (continued) Current Channel The channel over which the Bridge Varies is communicating with clients. Security The type of security for which the Bridge is configured. Open System (no security) Rx Data Rate (Mbps) The most recent data reception rate. N/A Tx Data Rate (Mbps) The most recent data transmission rate. N/A Link Quality N/A The normalized transmitted data rate (that is, the current data rate over the maximum data rate).
Using the Configuration Management System Changing System Properties 29 Under System Configuration, click System Properties. The System Properties page displays the properties of the selected Bridge. You can change properties by entering a value in a field (see Table 9). When you are finished, click Apply. Table 9 describes the properties. Table 9 System Properties Page Property Description Device Name This name appears in the System 3Com WWB Summary window.
30 CHAPTER 3: CONFIGURING THE BRIDGE Table 9 System Properties Page (continued) Web GUI Protocol Setting IP Network Properties This setting allows users to enable the secure data exchange scheme over SSL during a configuration session. ■ HTTPS — enables SSL technology. ■ HTTP — disables SSL technology. HTTP Under System Configuration, click IP Network. The IP Network Properties page appears, where you can change the settings shown in Table 10.
Using the Configuration Management System Setting Wireless Network Properties 31 Under System Configuration, click Wireless Network. The Wireless Network Properties page appears, where you can select different wireless settings, as described in Table 11. When you are finished, click Apply. The Bridge supports Dynamic and Static Turbo modes and boosts throughput up to 108 Mbps. The Dynamic Turbo mode allows automatic switching between normal and turbo modes without modification by the user.
32 CHAPTER 3: CONFIGURING THE BRIDGE Table 11 Wireless Network Page (continued) Wireless LAN Service Area Select Attach to any WLAN Service Area (ESSID) automatically to allow the Bridge to associate with any access point without specifying the ESSID. In this mode, the Bridge uses the ESSID of the access point with the best signal strength. This mode is not available when the network mode is Ad-hoc (Peer-to-Peer).
Using the Configuration Management System 33 Table 11 Wireless Network Page (continued) Antenna Selection Data Preamble Select an antenna for the radio signal: ■ Internal — this default setting should be used in most circumstances. ■ External and one internal antenna — this setting automatically determines which antenna is best for sending packets to individually attached clients. Choose this setting if the Bridge is located in a place that is surrounded or hindered by metal paths or walls.
34 CHAPTER 3: CONFIGURING THE BRIDGE Setting Up an Ad-Hoc Network Operating in ad-hoc mode, two or more Bridges can associate among themselves to form an ad-hoc network without the intervention of an access point. You may wish to set up an ad-hoc network, for example, if a group is working away from the office, or if a group in the office needs to share files apart from the wired LAN. CAUTION: To ensure correct operation, the settings on the two Bridges must match exactly.
Using the Configuration Management System Changing Wireless Security Settings 35 Under System Configuration, click Wireless Security. The Wireless Security Settings page appears, where you can select the type of security to be used on the Bridge. The Bridge can be configured to support three types of data encryption: WEP, TKIP, and AES. After selecting a data encryption type, you can select an authentication type. The following sections describe the settings.
36 CHAPTER 3: CONFIGURING THE BRIDGE 104/128-bit Shared Key This option can be used with other 3Com 11a/b/g Wireless LAN devices and with equipment from certain manufacturers that also support 128-bit shared key encryption. It provides a higher level of security than the 40-bit Shared Key (Wi-Fi) option and uses a more complicated type of encryption. This type of security requires you to set up encryption using a string or shared keys as described in “40/64-bit Shared Key (WEP)” on page 35.
Using the Configuration Management System 37 AES The Advanced Encryption Standard (AES) option uses the highest security cipher for data encryption. To use AES: 1 On the Wireless Security page, select AES. 2 Select WPA-PSK for home network or WPA for the scenarios where RADIUS servers are employed: ■ WPA-PSK: Enter a pass-phrase key or hexidecimal key. The key can be generated based on a pass-phrase or a sequence of manually entered 64 hexidecimals.
38 CHAPTER 3: CONFIGURING THE BRIDGE Table 12 RADIUS Authentication Server Settings (continued) Changing SNMP Settings Secondary RADIUS Server Enter the IP address of the secondary RADIUS Authentication Server. Make sure this address matches the address set in the RADIUS Authentication software. Secondary RADIUS Port Enter the port number of the secondary RADIUS Authentication Server. Make sure this number matches the number set in the RADIUS Authentication software. The default port is 1812.
Using the Configuration Management System Using the Access Control List 39 You can use the Access Control List to allow or prohibit access to the wireless network from Ethernet clients. Follow these steps to build the Access Control List: 1 Under System Configuration, click Access Control List. 2 On the Access Control List page, click Add. The Access Control List New ACL page appears.
40 CHAPTER 3: CONFIGURING THE BRIDGE Serial Port Under System Configuration, click Serial Port to set up network serial port operation. About UART A Universal Asynchronous Receiver/Transmitter (UART) is the fundamental hardware for serial communication, controlling the speed and method of data transfer of the serial port. Applications utilizing a network serial port between an RS-232 interface and a wireless device use a TCP/IP socket connection.
Using the Configuration Management System 41 Configuring UART Settings For proper operation, it is imperative that these settings always match the settings of the device to which the bridge is connected via the RS-232 port. There are two groups of parameters that need to be configured to accomplish this task: UART Settings and Flow Control Settings. Flow control is the process of adjusting the flow of data from one device to another to ensure that the receiving device can handle all of the incoming data.
42 CHAPTER 3: CONFIGURING THE BRIDGE Applying Settings After you set the UART settings, network serial port settings, and operation mode, select Apply to make the settings take effect. The socket can be substantially established between a client and server; that is, a Bridge in server mode and the other in client mode. The Bridge with the Network Serial Port option set cannot work alone. Generally, a Bridge is set to server mode first, which listens to a designated port.
Using the Configuration Management System Restoring the Bridge to Factory Defaults 43 You can restore Bridge settings to the defaults that were set at the factory either manually or through software. To restore the settings manually, insert a pointed object (such as the end of a straightened paper clip) into the reset hole on the back of the Bridge, and hold for five seconds. The reset hole is accessible with the Bridge in the cradle, as shown in Figure 16, or with the Bridge out of the cradle.
44 CHAPTER 3: CONFIGURING THE BRIDGE Upgrading the System You can download firmware updates or updates of the Configuration Management System from the 3Com Web site and install those updates on the Bridge. Options for upgrading the system include using a Trivial File Transfer Protocol (TFTP) server or File Transfer Protocol (FTP) server. The Bridge acts as a TFTP or FTP client to receive the download.
Using the Configuration Management System 45 Using HTTP The general instructions for installing the upgrade using HTTP are: 1 Launch the Configuration Management System. 2 Under Tools, click Upgrade System. 3 Select HTTP. 4 Click Browse to locate the downloaded firmware file. 5 Click Upgrade to start the upgrade process. The upgrade takes place through the HTTP protocol from the local computer.
46 CHAPTER 3: CONFIGURING THE BRIDGE Restoring a Configuration If you have stored a backup configuration on your computer, you can restore the configuration as follows: 1 Under Tools, click Restore Wireless Workgroup Bridge. 2 In the next page, click Browse and select the backup file to upload. 3 Click Restore. The configuration is restored and activated on the Bridge. This operation may cause the Bridge to reboot.
Using the Configuration Management System Viewing Connection Status Viewing System Summary 47 Under System Summary, click Connection Status to view a summary of the Bridge’s current connection information. See Table 8 on page 27 for details. Under System Summary, you can view the following information: Table 14 System Summary Page Property Description Default Value Device Name The name assigned to the Bridge.
4 Diagnosing Problems TROUBLESHOOTING If you have difficulty with the Bridge, try the solutions in the following table. Table 15 Troubleshooting Symptom Solution(s) 16 devices have been connected to the Bridge, either simultaneously or sequentially. After connecting another device, the new device cannot associate with the network. The Bridge supports up to 16 specific clients (for example, computers and printers) and keeps track of them using a client list of MAC addresses.
50 CHAPTER 4: TROUBLESHOOTING Table 15 Troubleshooting (continued) After you change the IP address, after you restore a backup configuration, or after you reset the Bridge to factory defaults, the Configuration Management System stops responding and you cannot continue configuring the Bridge. If you change the IP address and click Apply, you cannot continue to configure the device using the old IP address.
Disconnecting the Bridge 51 Table 15 Troubleshooting (continued) You are running Windows NT. After you connect the Bridge, your computer cannot obtain a valid IP address. The Bridge configuration settings may not be compatible with the network. If they are not, and your Windows NT computer is set up to obtain its IP address from a DHCP server, the Bridge is unable to associate with the network to obtain the IP address. To work around this, set a static IP address on your computer.
52 CHAPTER 4: TROUBLESHOOTING Upgrading Bridge Firmware Firmware is the software that is installed on the Bridge at the factory. Some problems can be solved by installing a new version of the firmware.
A OBTAINING SUPPORT FOR YOUR 3COM PRODUCT 3Com offers product registration, case management, and repair services through eSupport.3com.com. You must have a user name and password to access these services, which are described in this appendix. Register Your Product to Gain Service Benefits To take advantage of warranty and other service benefits, you must first register your product at: http://eSupport.3com.
54 APPENDIX A: OBTAINING SUPPORT FOR YOUR 3COM PRODUCT Purchase Extended Warranty and Professional Services To enhance response times or extend your warranty benefits, you can purchase value-added services such as 24x7 telephone technical support, software upgrades, onsite assistance, or advanced hardware replacement. Experienced engineers are available to manage your installation with minimal disruption to your network.
Contact Us Telephone Technical Support and Repair 55 To obtain telephone support as part of your warranty and other service benefits, you must first register your product at: http://eSupport.3com.
56 APPENDIX A: OBTAINING SUPPORT FOR YOUR 3COM PRODUCT Country Telephone Number Country Telephone Number Europe, Middle East, and Africa Telephone Technical Support and Repair From anywhere in these regions, call: +44 (0)1442 435529 From the following countries, call the appropriate number: Austria Belgium Denmark Finland France Germany Hungary Ireland Israel Italy 01 7956 7124 070 700 770 7010 7289 01080 2783 0825 809 622 01805 404 747 06800 12813 01407 3387 1800 945 3794 199 161346 Luxembourg Neth
END USER LICENSE AGREEMENT Customer shall take all steps necessary to protect Wind River's and its licensors' proprietary rights in the Run-Time Module and to ensure that each Run-Time Module distributed by Customer will be accompanied by a localized copy of an End User License Agreement.
REGULATORY INFORMATION The 3Com 11 a/b/g Wireless Workgroup Bridge (Model WL-560) must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. This device complies with the following radio frequency and safety standards. This product contains encryption. It is unlawful to export out of the U.S. without obtaining a U.S. Export License. This product does not contain any user serviceable components.
MANUFACTURER’S DECLARATION OF CONFORMITY 3Com Corporation 350 Campus Drive Marlborough, MA 01752-3064, USA (800) 527-8677 Date: June 30, 2004 Declares that the Product: Brand Name: 3Com Corporation Model Number: WL-560 Equipment Type: 11a/b/g Wireless Workgroup Bridge Complies with Part 15 of the FCC rules.
CANADA – INDUSTRY CANADA (IC) This device complies with RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.
EUROPE – EU DECLARATION OF CONFORMITY Marking by the above symbol indicates compliance with the Essential Requirements and other relevant provisions of the R&TTE Directive of the European Union (1999/5/EC). This equipment meets the following conformance standards: EN300 328, EN301 893, EN301 489-17, EN60950 NOTE: To ensure product operation is in compliance with local regulations, select the country in which the product is installed. Refer to “Configuring the Bridge” in the user guide.
Spanish Por medio de la presente 3Com Corporation declara que el 11a/b/g Wireless Workgroup Bridge cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE Portuguese 3Com Corporation declara que este 11a/b/g Wireless Workgroup Bridge está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. EUROPE – RESTRICTIONS FOR USE OF 2.
EUROPE – RESTRICTIONS FOR USE OF 5GHZ FREQUENCIES IN EUROPEAN COMMUNITY COUNTRIES European Community Countries 5150-5250 MHz 5250-5350 MHz 5470-5725MHz Channels: 36, 40, 44, 48 Channels: 52, 56, 60, 64 Channels: 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 Indoor Only Indoor Only Indoor/Outdoor ✔ X X ✔ ✔ X ✔ ✔ ✔ Austria Belgium, France, Switzerland, Liechtenstein Denmark, Finland, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden,
