USER'S MANUAL COOKER HOB VITROLINE HI-LIGHT
Dear customer Operating instructions The built-in glass-ceramic cooker hob is intended for domestic use. Our products are packaged using eco-compatible materials that can be recycled, disposed of or destroyed. For this reason, we have appropriately indicated the materials comprising the packaging. Should the appliance no longer be needed, dispose of it responsibly so as to not harm the environment. Deliver it to a specialised waste disposal facility.
IMPORTANT WARNINGS Installation of the appliance and connection to the mains electricity must be carried out by qualified personnel only. • Several parts of the appliance heat up during use. Keep children away from the appliance and warn them of the risk of burns. • Overheated fat can easily ignite. Be extremely careful when preparing dishes that require the use of bacon fat or oil (e.g. chips). • Do not operate the cooking zones without any pots on them. • Do not use the appliance to heat the room.
Prior to first use Important warnings The glass-ceramic surface must be cleaned with the aid of a damp sponge and dish soap. Do not use aggressive and abrasive detergents, pot scrubbers and stain or rust removers. • Do not operate the cooking zones without any pots on them. Do not use the appliance to heat the room! • Make sure that the cooking zones and pots are always clean and dry, so as to ensure optimal heat transmission and to avoid damaging the glass-ceramic surface.
Energy saving • Do not use clay pots as these may scratch the glass-ceramic surface. • The diameter of the pot base must match that of the cooking zone. Using pots that are too small causes energy wastage and may damage the cooker hob. • Use the lid if compatible with the type of food preparation. • The pots must be suitably sized according to the amount of food being cooked. Preparing small amounts of food in large pots is a waste of energy.
GLASS-CERAMIC COOKER HOB MODEL "7316-000 " 1.Front left Hi-Light cooking zone 2.Rear central Hi-Light cooking zone 3.Front right Hi-Light cooking zone 4. Cooker hob control unit Cooker hob controls A.Cooker hob on/off sensor B.Heat setting or residual heat indicators C.Cooking zone on/selection sensor (+) D.Safety lock/child safety device on/off sensor E.Sensor (-) F.Dual circuit sensor G.
Turning the cooking zonesoff Turning the cooker hob off Safety lock / child safety device Turning off the cooking zone before cooking is completed allows for saving energy by using the residual heat to complete cooking. • The selected cooking zone must be activated. • Press the on/off sensor »-« (E) to lower the heat setting to »0« and after 10 seconds, the cooking zone will turn off. Cooker hob operation Fast turning off • The selected cooking zone must be activated.
Safety function and error signals The cooker hob is equipped with sensors to protect it against overheating. If overheating occurs, the cooking zones closest to the control panel turn off. ERROR CODE ERROR DESCRIPTION ER03 + CONTINUOUS BUZZER Continuous activation of the sensors (BUTTONS) for more than 10 seconds, due to the presence of objects or liquids on the glass in the touch-control area.
GLASS-CERAMIC COOKER HOB MODEL "7352-010" Control knobs The cooking zones are controlled by knobs that turn clockwise and are connected to an energy regulator. The numbers 1 to 8 indicate the various heat settings: 1 is the lowest heat setting and 8 the highest, while 0 corresponds to the "off " mode. The cooking zone controlled by each knob is visualised in the identification diagram adjacent to each knob. A. Control knob B. Residual heat indicator C. Cooking zone identification diagram D.
COOKER HOB CLEANING AND MAINTENANCE The glass-ceramic surface must be cleaned after every use, as any remaining small stains will burn on the hot surface. For ordinary maintenance purposes, use special detergents that form a protective film against dirt. Fig. 1 Before every use of the hob, wipe away any dust from the glassceramic surface and clean any dirt on pot bases, as it may scratch the cooking zone (Fig. 1). Warning: do not use steel wool sponges or abrasive detergents that may scratch the surface.
COOKER HOB INSTALLATION Important warnings • Installation of the appliance and connection to the mains electricity must be carried out by qualified personnel only. • The lining of the worktop walls must be suitably treated with adhesives capable of withstanding temperatures of 100°C (if not, the colour and shape of the lining may alter). • The appliance must be fitted into the worktop on a cabinet at least 600 mm wide.
Installation procedure ▪ The worktop must be completely level. ▪ Protect the cut-out surfaces. ▪ Screw on the support elements provided using the respective screws on the front and rear end of the cooker hob (already configured with the relative holes and slots). ▪ Connect the cooker hob to the mains electricity (consult the connection instructions). ▪ Position the cooker hob in the cut-out. ▪ Press it forcefully agianst the worktop.
interrupts and will not resume until the objects are removed. The hob may not be used during this operation. WARNING! Before each operation, disconnect the appliance from the mains electricity. Depending on the mains voltage, the appliance must be connected according to the electrical diagram below. The protection conductor (equipotential protection conductor) must be connected to the earthing clamp. The connection wire must be fed through the bracket that protects it against accidental movements.
SPECIFICATIONS - MODEL "7316-000" Code Width Worktop cut-out size Electrical connection Rated voltage Cooking zones ( Ø mm, W ) - front left - rear centre - front right Total power (W) SPECIFICATIONS - MODEL Code Width Worktop cut-out size Electrical connection Rated voltage Cooking zones ( Ø mm, W ) - front left - rear centre - front right Total power (W) 7316-000 Ø 520 mm Ø 500 mm 220-240 V~ or 380-415 V 2N~, 50/60 Hz 220-240 V~, 50/60 Hz 140, 1.200 180/120, 1.700/700 140, 1.200 4.
Foster spa via M.S. Ottone, 18/20 42041 Brescello (RE) - Italy tel. +39.0522.687425 - tel. Servizio Assistenza +39.0522.684450 fax +39.0522.686019 - fax Servizio Ricambi +39.0522.962166 e-mail: service@fosterspa.com www.fosterspa.