Avion airplanes DUCK user manual
Avion airplanes What you need Filament Hardware Possible to print with Prusa Slicer 2.4.0 and Cura. PLA LW / POLYLIGHT 1.
Avion airplanes Model specifications Wingspan Length Print weight Takeoff weight Wing area Wing load Parts list Fuselage 1000mm 518mm approx 279g approx 484g 21,5 dm² 22,5 g/dm² F_1 F_2 F_3 F_4 Canopy Motor_mount F_L_Rib F_R_Rib Printed parts 3,48g 14,56g 25,29g 25,26g 4,95g 0,99g 1,42g 1,42g Wing LEFT E_R_3_Rib Wing RIGHT W_R_7 W_L_1 W_L_2 W_L_2_Rib W_L_3 W_L_3_Cover W_L_4 W_L_5 W_L_6 W_L_7 E_R_3 W_R_6 W_R_5 E_R_2 W_R_3_Cover W_R_4 E_R_1 W_R_2_Rib F_R_Rib W_R_3 Motor_mount W_R_2 W_R_1 F
Avion airplanes Fuselage assembly You will need Fuselage assembly F_1, F_2, F_3, F_4, F_L_Rib, F_R_Rib, Motor_mount, CA glue, Activator, Snap-off knife, ø1x285mm carbon rod 2x CA 3. Glue F_2 and F_3 with medium CA. CA 1. Glue ø1x285mm carbon rod 2x with medium CA glue into F_1 part. If you have problem with printing very end of the F_1 part, use putty to fill imperfections. 2. Glue F_1 and F_2 with medium CA. CA DUCK user manual 4. Glue Motor_mount and F_4 together with medium CA.
Avion airplanes Fuselage assembly Fuselage assembly 5. Prepare your Motorand ESC. Before soldering Motor and ESC together make sure, that all cables has necessary length. 7. Cut or drill 4x hole for servocables into F_3 part. Inner parts cut compleatley off. 6. Install Motor and secure ESC.
Avion airplanes Fuselage assembly Fuselage assembly CA 8. Glue F_3 and F_4 with medium CA. CA CA 9. Glue F_L_Rib and F_R_Rib with medium CA into fuselage. 10. Fuselage is done.
Avion airplanes 3. Glue parts W_L_1 and W_R_1 to the fuselage. Apply medium CA glue on wing parts (or fuselage) and then slide them on the carbon rods all the way to the fuselage. CA CA DUCK user manual CA 2. Glue ø1x487mm carbon rod 2x with medium CA glue into F_4 part. Make sure, that parts W_L_1 and W_R_1 will fit correctly. CA CA CA 1. Glue ø1x571mm carbon rod 2x with medium CA glue into F_2 part. Make sure, that parts W_L_1 and W_R_1 will fit correctly.
Avion airplanes Wings assembly 5. Prepare Corona DS-843MG servos and make sure, that servo cables has necessary length. 7. Servo and servo horn position. 6. Install servos into W_L_2 and W_R_2 parts with original screws. Servo horns must be installed before gluing next parts of the wing! 8. Glue parts W_L_2_Rib and W_R_2_Rib to the W_L_2 and W_R_2 with medium CA glue.
Avion airplanes Wings assembly CA CA CA 9. Glue parts W_L_3 and W_R_3 to the W_L_2 and W_R_2. Apply medium CA glue on wing parts and then slide them on the carbon rods all the way to the previous part of the wing. 11. Glue parts W_L_5 and W_R_5 to the W_L_4 and W_R_4. Apply medium CA glue on wing parts and then slide them on the carbon rods all the way to the previous part of the wing. CA Wings assembly CA CA CA 12. Glue parts W_L_6 and W_R_6 to the W_L_5 and W_R_5.
Avion airplanes Wings assembly Elevons assembly You will need CA CA CA CA 1. Glue ø1x361mm carbon rod 2x with medium CA glue into E_L_1 and E_R_1 part. CA CA 13. Glue parts W_L_7 and W_R_7 to the W_L_6 and W_R_6. Apply medium CA glue on wing parts and then slide them together. E_L_1, E_L_2, E_L_3, E_L_3_Rib, E_R_1, E_R_2, E_R_3, E_R_3_Rib, ø1x361mm carbon rod 2x (elevons) f Avion Airplanes I CA DUCK user manual 2. Glue parts E_L_2 and E_R_2 to the E_L_1 and E_R_1.
Avion airplanes Elevons assembly Elevons assembly 3. Glue parts E_L_3 and E_R_3 to the E_L_2 and E_R_2. Apply medium CA glue on elevon parts and then slide them on the carbon rods all the way to the previous part of the elevon. 5. Elevons are done. CA CA CA DUCK user manual CA 4. Glue parts E_L_3_Rib and E_R_3_Rib to the E_L_3 and E_R_3 with medium CA glue.
Avion airplanes Completion You will need Completion Canopy, W_L_3_Cover, W_R_3_Cover, ø2x385mm carbon rod 2x (elevons axles), Steel wire, carbon rod or clevis (pushrods) CA glue 1. Use ø2x385mm carbon rod 2x as elevons axles. Don‘t insert them all the way in at this point in case that you will need to make pushrods or other adjustments. 2. Set elevons to neutral position and install pushrods. Make sure, that everything moves freely. If not, use sand paper or drillbit and make necessary adjustments.
Avion airplanes Center of gravity Before first flight CG is marked on W_L_1 and W_R_1 on the bottom side and it is 206mm from the very tip of the F_1 part. After maiden flight you can shift CG slightly front or back to fit your flying style perfectly. Don‘t shift CG position too much at once, wing can lose it‘s stability. It is also possible to change a little bit angle of the motor with small washers to adjust behavior of the wing during flight.
