3M™ Bondo® Fiberglass Resin for Fiberglass Resin Kit, P.N. 420, 420C, 420ES, 420T, 422, 422C 05/19/14 Safety Data Sheet Copyright,2014,3M Company. All rights reserved.
3M™ Bondo® Fiberglass Resin for Fiberglass Resin Kit, P.N. 420, 420C, 420ES, 420T, 422, 422C 05/19/14 Serious Eye Damage/Irritation: Category 2B. Carcinogenicity: Category 2. Specific Target Organ Toxicity (single exposure): Category 1. Specific Target Organ Toxicity (central nervous system): Category 3. Specific Target Organ Toxicity (repeated exposure): Category 1. 2.2.
M™ Bondo® Fiberglass Resin for Fiberglass Resin Kit, P.N. 420, 420C, 420ES, 420T, 422, 422C 05/19/14 Use only outdoors or in a well-ventilated area. Wear protective gloves and eye/face protection. Do not eat, drink or smoke when using this product. Wash thoroughly after handling. Response: IF INHALED: Remove person to fresh air and keep comfortable for breathing. IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower.
3M™ Bondo® Fiberglass Resin for Fiberglass Resin Kit, P.N. 420, 420C, 420ES, 420T, 422, 422C 05/19/14 Inhalation: Remove person to fresh air. If you feel unwell, get medical attention. Skin Contact: Immediately wash with soap and water. Remove contaminated clothing and wash before reuse. If signs/symptoms develop, get medical attention. Eye Contact: Immediately flush with large amounts of water for at least 15 minutes. Remove contact lenses if easy to do. Continue rinsing.
3M™ Bondo® Fiberglass Resin for Fiberglass Resin Kit, P.N. 420, 420C, 420ES, 420T, 422, 422C 05/19/14 SECTION 7: Handling and storage 7.1. Precautions for safe handling Avoid eye contact. Keep out of reach of children. Do not handle until all safety precautions have been read and understood. Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Ground/bond container and receiving equipment. Use only non-sparking tools. Take precautionary measures against static discharge.
3M™ Bondo® Fiberglass Resin for Fiberglass Resin Kit, P.N. 420, 420C, 420ES, 420T, 422, 422C 05/19/14 Eye/face protection Select and use eye/face protection to prevent contact based on the results of an exposure assessment. The following eye/face protection(s) are recommended: Indirect Vented Goggles Skin/hand protection Select and use gloves and/or protective clothing approved to relevant local standards to prevent skin contact based on the results of an exposure assessment.
3M™ Bondo® Fiberglass Resin for Fiberglass Resin Kit, P.N. 420, 420C, 420ES, 420T, 422, 422C 05/19/14 Vapor Density Density Specific Gravity Solubility In Water Solubility in Water Solubility- non-water No Data Available 1.14 g/ml 1.
3M™ Bondo® Fiberglass Resin for Fiberglass Resin Kit, P.N. 420, 420C, 420ES, 420T, 422, 422C 05/19/14 SECTION 11: Toxicological information The information below may not be consistent with the material classification in Section 2 if specific ingredient classifications are mandated by a competent authority.
3M™ Bondo® Fiberglass Resin for Fiberglass Resin Kit, P.N. 420, 420C, 420ES, 420T, 422, 422C 05/19/14 Liver Effects: Signs/symptoms may include loss of appetite, weight loss, fatigue, weakness, abdominal tenderness and jaundice. Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination, nausea, slowed reaction time, slurred speech, giddiness, and unconsciousness.
3M™ Bondo® Fiberglass Resin for Fiberglass Resin Kit, P.N.
3M™ Bondo® Fiberglass Resin for Fiberglass Resin Kit, P.N. 420, 420C, 420ES, 420T, 422, 422C Styrene Monomer Ingestion Styrene Monomer Ingestion Styrene Monomer Inhalation Silica 05/19/14 mg/l NOAEL 400 mg/kg/day 60 days Rat NOAEL 400 mg/kg/day during gestation Multiple animal species Rat NOAEL 2.
3M™ Bondo® Fiberglass Resin for Fiberglass Resin Kit, P.N.
3M™ Bondo® Fiberglass Resin for Fiberglass Resin Kit, P.N. 420, 420C, 420ES, 420T, 422, 422C 05/19/14 waste regulations. Consult with the respective regulating authorities to determine the available treatment and disposal facilities. SECTION 14: Transport Information For Transport Information, please visit http://3M.com/Transportinfo or call 1-800-364-3577 or 651-737-6501. SECTION 15: Regulatory information 15.1. US Federal Regulations Contact 3M for more information.
3M™ Bondo® Fiberglass Resin for Fiberglass Resin Kit, P.N. 420, 420C, 420ES, 420T, 422, 422C 05/19/14 15.4. International Regulations Contact 3M for more information. This SDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
3M™ Bondo® MEKP Liquid Hardener, P.N. 411, 609, 912, 912M, 912C, 912ES, 7653081 01/21/14 Safety Data Sheet Copyright,2014,3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.
3M™ Bondo® MEKP Liquid Hardener, P.N. 411, 609, 912, 912M, 912C, 912ES, 7653081 01/21/14 Symbols Flame | Corrosion | Exclamation mark | Pictograms Hazard Statements Heating may cause a fire. Harmful if swallowed. Causes serious eye damage. Causes severe skin burns and eye damage. Harmful if inhaled. Precautionary Statements General: Keep out of reach of children. Prevention: Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Keep away from clothing and other combustible materials.
3M™ Bondo® MEKP Liquid Hardener, P.N. 411, 609, 912, 912M, 912C, 912ES, 7653081 01/21/14 May cause chemical gastrointestinal burns. 64% of the mixture consists of ingredients of unknown acute inhalation toxicity. SECTION 3: Composition/information on ingredients Ingredient Dimethyl Phthalate Methyl Ethyl Ketone Peroxide 2,2,4-Trimethyl-1,3-Pentanediol Diisobutyrate Methyl Ethyl Ketone Hydrogen Peroxide Water C.A.S. No.
3M™ Bondo® MEKP Liquid Hardener, P.N. 411, 609, 912, 912M, 912C, 912ES, 7653081 01/21/14 5.3. Special protective actions for fire-fighters Water may not effectively extinguish fire; however, it should be used to keep fire-exposed containers and surfaces cool and prevent explosive rupture. SECTION 6: Accidental release measures 6.1. Personal precautions, protective equipment and emergency procedures Evacuate area. Keep away from heat/sparks/open flames/hot surfaces. - No smoking.
3M™ Bondo® MEKP Liquid Hardener, P.N. 411, 609, 912, 912M, 912C, 912ES, 7653081 01/21/14 Hydrogen Peroxide 7722-84-1 Hydrogen Peroxide 7722-84-1 Methyl Ethyl Ketone 78-93-3 Methyl Ethyl Ketone 78-93-3 Amer Conf of Gov. Indust. Hyg. US Dept of Labor - OSHA Amer Conf of Gov. Indust. Hyg. US Dept of Labor - OSHA TWA:1 ppm TWA:1.4 mg/m3(1 ppm) TWA:200 ppm;STEL:300 ppm TWA:590 mg/m3(200 ppm) Amer Conf of Gov. Indust. Hyg. : American Conference of Governmental Industrial Hygienists American Indust.
3M™ Bondo® MEKP Liquid Hardener, P.N. 411, 609, 912, 912M, 912C, 912ES, 7653081 01/21/14 9.1. Information on basic physical and chemical properties Liquid General Physical Form: Slight odor. Clear. Odor, Color, Grade: No Data Available Odor threshold No Data Available pH No Data Available Melting point 244 ºF Boiling Point > 200 ºF [Test Method: Closed Cup] [Details: No flash to Flash Point boiling point.
3M™ Bondo® MEKP Liquid Hardener, P.N. 411, 609, 912, 912M, 912C, 912ES, 7653081 01/21/14 None known. Refer to section 5.2 for hazardous decomposition products during combustion. SECTION 11: Toxicological information The information below may not be consistent with the material classification in Section 2 if specific ingredient classifications are mandated by a competent authority.
3M™ Bondo® MEKP Liquid Hardener, P.N.
3M™ Bondo® MEKP Liquid Hardener, P.N.
3M™ Bondo® MEKP Liquid Hardener, P.N.
3M™ Bondo® MEKP Liquid Hardener, P.N.
3M™ Bondo® MEKP Liquid Hardener, P.N. 411, 609, 912, 912M, 912C, 912ES, 7653081 01/21/14 Dimethyl Phthalate 131-11-3 Trade Secret 30 - 60 15.2. State Regulations Contact 3M for more information. 15.3. Chemical Inventories The components of this product are in compliance with the chemical notification requirements of TSCA. Contact 3M for more information. 15.4. International Regulations Contact 3M for more information. This SDS has been prepared to meet the U.S.