3M™ Super Close Projection System SCP712 Operator’s Guide A/C Power Service Computer/ Component Control 3M Projection Systems Department 1-800-328-1371 © 3M 2008 All Rights Reserved. www.3m.
3M™ Super Close Projection System SCP712 Operator’s Guide Table of Contents INTRODUCTION .................................................................................................................................... 3 Thank you for choosing 3M equipment............................................................................................................. 3 Important Notice ..........................................................................................................................
M™ Super Close Projection System SCP712 Operator’s Guide INTRODUCTION Thank you for choosing 3M equipment. This product has been produced in accordance with 3M’s quality and safety standards to provide smooth and trouble free use in the years to come. For optimum performance, please follow the operating instructions carefully. We hope you will enjoy using this high performance product in your classroom, meetings, presentations, and training sessions.
3M™ Super Close Projection System SCP712 Operator’s Guide Safety Information Please read, understand, and follow all safety information contained in these instructions prior to the use of this projector. Retain these instructions for future reference. Intended Use Before operating the machine, please read the entire manual thoroughly. This product was designed, built and tested for use indoors, using 3M lamps and hardware.
3M™ Super Close Projection System SCP712 WARNING • • • • • • • • • Operator’s Guide English To reduce the risk associated with exposure to hazardous voltage: - Do not remove any screws other than those specified in the lamp replacement instructions. To reduce the risk associated with hazardous voltage: - Do not operate this projector in wet environments or outdoors. - Do not modify this projector or power cord.
3M™ Super Close Projection System SCP712 Operator’s Guide Contents of Shipping Box This projector is shipped with the necessary cables required for standard VCR, PC or laptop computer connections. Carefully unpack and verify that you have all of the items shown below. If any of these items are missing, please contact your place of purchase. The shipping carton contains the following items illustrated below. If any of these items are missing, please contact your place of purchase. 1. 2. 3. 4. 5. 6.
3M™ Super Close Projection System SCP712 Operator’s Guide Product Description The 3M SCP712 integrates metal halide lamp and Digital Light Processing™ (DLP) technology. It accepts input from computer and/or video sources and projects a bright image.
3M™ Super Close Projection System SCP712 Operator’s Guide Parts Identification 1. 2. 3. 4. 5. 6. 7. 8. 9. Lens Remote Control IR Sensor Height Adjustment Feet Power Cord Connection Input Terminals Slot for Kensington™ Lock USB Port Focus Adjustment On/Off Standby 8 1 6 4 3 7 5 2 3 Front View 9 Top View © 3M 2008. All Rights Reserved.
3M™ Super Close Projection System SCP712 Operator’s Guide Terminal Connections AC Power Service 1 2 Computer/ Component Control 3 4 # SCP712 Function 1 A/C Power Connect AC power cord to projector. 2 USB Service Connect projector USB (B-type) to computer USB port. 3 COMPUTER/COMPONEN T Input RGB signal from a computer. 4 CONTROL Connect projector RS-232 control port to computer serial port.
3M™ Super Close Projection System SCP712 Operator’s Guide Setup and System Configuration © 3M 2008. All Rights Reserved.
3M™ Super Close Projection System SCP712 Operator’s Guide Machine Specifications Item Acoustic Noise Level Auto Detect & Install Computer Compatibility Specification Normal Mode: Typical 38 dB(A) ECO Mode: Typical 35 dB(A) Automatically recognizes the connection of I/O module Automatically saves user adjustments Horizontal Sync: 15 – 82 kHz Vertical Sync: 50 – 85 Hz Rel Humidity: 30% to 70% Conditions for usage environment Altitude/Temperature 0-5000 ft. (with Fan Normal Mode) 5°C to 35°C 5000-7000 ft.
3M™ Super Close Projection System SCP712 Operator’s Guide Operating Instructions Projector Start Up Read the Important Safeguards before operating the SCP712. After all cable connections have been completed, the projector can be powered up. For best results, please observe the following start up sequence. 1. Turn all of the connected equipment on. 2. Plug the supplied power cord into the AC inlet of the projector. 3. Press the On/Standby button on the projector or remote control.
3M™ Super Close Projection System SCP712 Operator’s Guide Menu Navigation To display the on screen menus, press the MENU button on the remote control. Use the remote control Up/Down ARROW buttons to select the desired menu (see table below), then pull the TRIGGER button (bottom of remote control) to display it. Use the remote control ARROW buttons within a submenu to select the various options displayed on the screen, then pull the TRIGGER button to initiate that option or setting.
3M™ Super Close Projection System SCP712 Operator’s Guide Input Menu The Input Menu, shown below, is used to select the desired computer or video input source to be displayed on the projector. Input Source: Computer 1 Input Computer 1 / Component 1 Computer 2 / Component 2 RCA Video S-Video Feature Select input source Description 1. Computer 1 / Component 2 2. Computer 2 / Component 2 [Displays only when I/O module is connected] 3.
3M™ Super Close Projection System SCP712 Operator’s Guide Picture Menu The Picture Menu, shown below, is used to adjust the picture settings to display the best possible image.
3M™ Super Close Projection System SCP712 Operator’s Guide Picture Menu – Advanced The Picture Menu with the Advanced option selected, shown below, is used to adjust the projected image for Computer and Component inputs only.
3M™ Super Close Projection System SCP712 Operator’s Guide Audio Menu (Displays only if I/O Module is connected) The Audio Menu, shown below, is used to adjust the audio settings and select the audio input source to play through the projector.
3M™ Super Close Projection System SCP712 Operator’s Guide Setup Menu The Setup Menu, shown below, is used to configure the basic projector operating parameters.
3M™ Super Close Projection System SCP712 Operator’s Guide Information Menu The Information Menu, shown below, is used to display current projector configuration settings. Information Input Source: Computer 1 Input Resolution H Frequency V Frequency Lamp Hours System Hours IP Address Net Mask Gateway 1024 x 768 31.75 KHz 60 Hz 1235 2356 192.168.1.10 255.255.255.0 192.168.1.1 User Ver. Feature 0.0.
3M™ Super Close Projection System SCP712 Operator’s Guide Remote Control Functions Aim the remote control toward the projection screen or at the sensor. Press desired remote control button to send a signal to the projector. ON/ STANDBY INPUT/ SOURCE Press to enter Standby mode. Note: A confirmation message will display to ensure unit does not get turned off accidentally. Press and press again to select different computer and video inputs.
3M™ Super Close Projection System SCP712 Operator’s Guide Maintenance Installing or Replacing Batteries 1. Push on the cover and slide it upward to unlatch it. 2. Remove the cover. 3. Install two AAA batteries with the correct polarities and then replace the cover. Slide it downward until it locks into place. Note: Verify the battery cover is fully latched before using the remote control. © 3M 2008. All Rights Reserved.
3M™ Super Close Projection System SCP712 Operator’s Guide Lamp Replacement © 3M 2008. All Rights Reserved.
3M™ Super Close Projection System SCP712 Operator’s Guide Troubleshooting Common Problems and Solutions Symptom Cause Solution No power. The power cord is disconnected. Insert the power cord into AC socket. The desired input source is not selected. Press the remote control Input button to select a desired input source. The cables from the input source are not connected. Connect the cable to correct input source. The input source is not turned on or not displaying an image. (e.g.
Technical Support Contact: 3M Austin Center 3M Canada 3M Mexico, S.a. de C.V 3M Europe Please recycle. Building A147-5N-01 P.O. box 5757 Apartado Postal 14-139 Boulevard de l'Oise Litho in USA 6801 River Place Blvd. London, Ontario Mexico, D.F. 07000 95006 Cerge Pontoise Cedex ©3M 2008. All Rights Reserved.