MSDS

ManualsBrands3M ManualsCold ShrinkQTIII SKIRTED P60, 1KT/CTN

MATERIAL SAFETY DATA SHEET 7690 SERIES QT-III COLD SHRINK SILICONE RUBBER SKIRTED TERMINATION KITS.

05/06/11

_________________________________________________________________________________________________________

Page 1 of 2

Material Safety Data Sheet

utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is

obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit

thereon.

PRODUCT NAME:

7690 SERIES QT-III COLD SHRINK SILICONE RUBBER SKIRTED

TERMINATION KITS.

MANUFACTURER:

DIVISION:

Electrical Markets Division

ADDRESS:

3M Center, St. Paul, MN 55144-1000

EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)

Issue Date:

05/06/11

Supercedes Date:

03/19/09

Document Group:

26-5463-0

ID Number(s):

80-6109-2011-0, 80-6109-2012-8, 80-6109-2013-6, 80-6109-2014-4, 80-6109-2015-1, 80-6112-0163-5, 80-

6112-0297-1, 80-6112-1182-4, 80-6112-1183-2, 80-6112-1184-0, 80-6112-1185-7, 80-6114-3364-2, 80-6114-

3365-9, 80-6114-3367-5, 80-6114-4208-0

This product is a kit or a multipart product which consists of multiple, independently packaged components. An MSDS for

each of these components is included. Please do not separate the component MSDSs from this cover page. The document

numbers of the MSDSs for components of this product are:

26-2852-7

Revision Changes:

Kit initial issue message was modified.

Section 1: Manufacturer name was added.

Section 16: Disclaimer (first paragraph) was added.

Section 16: Disclaimer (second paragraph) was added.

Section 16: Web address was added.

Section 1: Address was added.

Summary of content (10 pages)

PAGE 2
MATERIAL SAFETY DATA SHEET 7690 SERIES QT-III COLD SHRINK SILICONE RUBBER SKIRTED TERMINATION KITS. 05/06/11 Company logo was added. Telephone header was added. Company Telephone was added. Section 1: Emergency phone information was added. Company Logo was deleted. Copyright was deleted. Kit: Manufacturer's name was deleted. Kit: Emergency phone information was deleted. Kit: Disclaimer (first paragraph) was deleted. Kit: Disclaimer (second paragraph) was deleted. Kit: Address line 1 was deleted.
PAGE 3
MATERIAL SAFETY DATA SHEET CC-2 Kit CABLE CLEANING PAD COMPONENT 05/06/11 Material Safety Data Sheet Copyright, 2011, 3M Company All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.
PAGE 4
MATERIAL SAFETY DATA SHEET CC-2 Kit CABLE CLEANING PAD COMPONENT 05/06/11 Eye Contact: Mild Eye Irritation: Signs/symptoms may include redness, pain, and tearing. Skin Contact: Moderate Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness. Allergic Skin Reaction (non-photo induced): Signs/symptoms may include redness, swelling, blistering, and itching.
PAGE 5
MATERIAL SAFETY DATA SHEET CC-2 Kit CABLE CLEANING PAD COMPONENT 05/06/11 5.3 PROTECTION OF FIRE FIGHTERS Special Fire Fighting Procedures: Water may not effectively extinguish fire; however, it should be used to keep fire-exposed containers and surfaces cool and prevent explosive rupture. Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus (SCBA). Unusual Fire and Explosion Hazards: Combustible liquid and vapor.
PAGE 6
MATERIAL SAFETY DATA SHEET CC-2 Kit CABLE CLEANING PAD COMPONENT 05/06/11 Use with appropriate local exhaust ventilation. Provide local exhaust ventilation at transfer points. Use in an enclosed process area is recommended. If exhaust ventilation is not available, use appropriate respiratory protection. Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below Occupational Exposure Limits and/or control mist, vapor, or spray.
PAGE 7
MATERIAL SAFETY DATA SHEET CC-2 Kit CABLE CLEANING PAD COMPONENT 05/06/11 Flash Point Flash Point Flammable Limits(LEL) Flammable Limits(UEL) Boiling Point 165 ºF [Test Method: Open Cup] 144 ºF [Test Method: Closed Cup] No Data Available No Data Available 380 ºF - 480 ºF Vapor Density > 1 [Ref Std: AIR=1] Vapor Pressure < 1 mmHg [@ 25 ºC] Specific Gravity pH Melting point 0.76 7.
PAGE 8
MATERIAL SAFETY DATA SHEET CC-2 Kit CABLE CLEANING PAD COMPONENT 05/06/11 CHEMICAL FATE INFORMATION Not determined. SECTION 13: DISPOSAL CONSIDERATIONS Waste Disposal Method: Incinerate in an industrial or commercial facility. As a disposal alternative, dispose of waste product in a facility permitted to accept chemical waste. EPA Hazardous Waste Number (RCRA): Not regulated Since regulations vary, consult applicable regulations or authorities before disposal.
PAGE 9
MATERIAL SAFETY DATA SHEET CC-2 Kit CABLE CLEANING PAD COMPONENT 05/06/11 NFPA Hazard Classification Health: 2 Flammability: 2 Reactivity: 0 Special Hazards: None National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies.
PAGE 10
MATERIAL SAFETY DATA SHEET CC-2 Kit CABLE CLEANING PAD COMPONENT 05/06/11 OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of use or application.