User Guide

ManualsBrands3M ManualsOther8560 3C CABLE BREAKOUT BOOTSRJS 3C PHASE REJACKETING

Cold Shrink- Silicone Rubber

8560 Series 3/C Cable Breakout Boots

RJS Series 3/C Phase Rejacketing System

™

Cold Shrink Silicone Rubber

8560 Series 3/C Cable Breakout

Boots and 3M

™

Silicone Rubber RJS

Series 3/C Phase Rejacketing System

are designed to be used in conjunction

with three 3M terminations, to seal the

breakout area and rejacket the phases

on three conductor cable.

Innovations in molded silicone

rubber technology, now make

possible a complete three conductor

all silicone termination. The

termination itself can be made with

™

Cold Shrink QT-III Indoor and

Outdoor Silicone rubber termination.

The phase legs (cores) of the three

conductor cable needs to be protected

from exposure to moisture, corrosion,

ozone, UV radiation, and other

physical conditions. These legs can

be rejacketed with 3M

™

RJS Silicone

Phase Rejacketing System. For those

applications not inside of a sealed

cabinet, the area where the three

cables break out from the overall

jacket need to be sealed. This area

can be sealed with the 3M

™

Silicone

Cold Shrink Cable Breakout Boots.

The result is an all silicone three

conductor termination that will stand

the test of time.

Breakout Boot

Rejacketing Sleeve

3 Conductor Cable

Summary of content (4 pages)

PAGE 1
3 Cold Shrink- Silicone Rubber 8560 Series 3/C Cable Breakout Boots RJS Series 3/C Phase Rejacketing System 3 Conductor Cable 3M™ Cold Shrink Silicone Rubber 8560 Series 3/C Cable Breakout Boots and 3M™ Silicone Rubber RJS Series 3/C Phase Rejacketing System are designed to be used in conjunction with three 3M terminations, to seal the breakout area and rejacket the phases on three conductor cable.
PAGE 2
(A) Seals Over Phase Shield (B) Seals Over Cable Jacket 3M™ Cold Shrink Silicone Rubber 8560 Series 3/C Cable Breakout Boots 3M 8561 through 8565 Silicone Cold Shrink Cable Breakout Boots are a series of open-ended molded rubber sealing assemblies that are factory expanded and mounted on removable inner-supporting plastic cores. They are supplied for field installation in a pre-stretched condition.
PAGE 3
M™ Cold Shrink Silicone Rubber 8560 Series–3/C Cable Breakout Boots Product Number Cable Phase Shield Diameter Range [A] Cable Outer Jacket Diameter Range [B] 8561 0.48 – 0.72" (12,2 – 18,3 mm) 1.17 – 1.94" (29,7 – 49,3 mm) 8561 0.61 – 0.95" (15,5 – 24,2 mm) 1.46 – 2.67" (37,1 – 67,8 mm) 8563 0.82 – 1.18" (20,8 – 30,0 mm) 1.92 – 3.10" (48,8 – 78,7 mm) 8564 1.02 – 1.63" (26,0 – 41,4 mm) 2.52 – 4.32" (64,0 – 109,8 mm) 8565 1.09 – 1.94" (27,7 – 49,3 mm) 2.60 – 4.
PAGE 4
Important Notice All statements, technical information, and recommendations related to Seller’s products are based on information believed to be reliable, but the accuracy or completeness thereof is not guaranteed. Before utilizing the product, the user should determine the suitability of the product for its intended use. The user assumes all risks and liability whatsoever in connection with such use.