Operator’s Guide …for projection 9000PD February 2005 78-6970-9380-1 Rev. B Copyright © 2004, 3M. All Rights Reserved.
(This page intentionally left blank for printed version)
M™ Digital WallDisplay Contents Contents Introduction Thank You for Choosing 3M .........................................................................................................................5 Safety Information .........................................................................................................................................5 Intended Use .......................................................................................................................................
Contents 3M™ Digital WallDisplay Menu System Menu Navigation .........................................................................................................................................26 Colorful—Bright Slider ...............................................................................................................................26 Warm—Cool Slider .....................................................................................................................................
Introduction 3M™ Digital WallDisplay Introduction Thank You for Choosing 3M Thank you for choosing 3M equipment. This product has been produced in accordance with 3M’s highest quality and safety standards to ensure smooth and troublefree use in the years to come. For optimum performance, please follow the operating instructions carefully. We hope you will enjoy using this high performance product in your meetings, presentations, and training sessions.
Introduction 3M™ Digital WallDisplay WARNING To reduce the risk associated with hazardous voltage: • Do not attempt to service the Wall Display other than performing routine lamp replacement. Service should only be performed by a 3M authorized service provider. Aside from the projection lamp assembly, there are no serviceable parts inside the unit. • Switch power “OFF” and disconnect the plug from electrical outlet before replacing the lamp. Grasp plug and pull to disconnect.
Introduction 3M™ Digital WallDisplay WARNING To reduce the risk of environmental contamination due to lead based solder: • Don’t throw circuit boards in the trash. Dispose of circuit boards in accordance with your respective governmental agencies for hazardous waste. To reduce the risk associated with radio interference: • This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.
Introduction 3M™ Digital WallDisplay IMPORTANT NOTES • In some countries, the voltage is not stable. This appliance is designed to operate within a range of 100~240 Vac. In these countries, it is recommended to install a power stabilizer unit. • Do not manually open or close the projection arm while the 3M Digital Wall Display is in operation. • Save the shipping box and packing materials in the event the 3M Digital WallDisplay should ever need to be moved. • For other types of wall material (e.g.
Introduction 3M™ Digital WallDisplay Product Safety Label The following safety label is used on or within the 3M Digital WallDisplay to alert you to this area requiring your attention. fro m 3 M Wall Display Save These Instructions The information contained in this manual will help you operate and maintain your 3M Digital WallDisplay. Trademarks The 3M logo and 3M are registered trademarks of 3M Company. Vikuiti is a trademark of 3M Company.
Introduction 3M™ Digital WallDisplay Netscape and the Netscape N and Ship’s Wheel logos are registered trademarks of Netscape Communications Corporation in the U.S. and other countries. Navigator and Communicator are also trademarks of Netscape Communications Corporation and may be registered outside the U.S. All other products are trademarks or registered trademarks of their respective companies. Patents 3M Digital WallDisplay is protected by Utility Patent 6,179,426 and Design Patent D442,205.
Introduction 3M™ Digital WallDisplay Model Identification and Differences Identify Model The nameplate, located behind the storage door, identifies the 3M Digital WallDisplay (DWD). Push the storage door to open it. The figure below shows the nameplate, and the table shows the model numbers and corresponding model names.
Introduction 3M™ Digital WallDisplay Contents The 3M Digital WallDisplay is shipped with the necessary cables required for standard VCR, PC, Macintosh or laptop computer connections. Carefully unpack and verify that you have all of the items shown below. If any are missing, please contact your place of purchase.
Introduction 3M™ Digital WallDisplay Part Identification 12 1 2 3 11 4 5 fro m 3 M Wall Display 6 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19.
Introduction 3M™ Digital WallDisplay 3M Digital WallDisplay Features The 3M Digital WallDisplay combines the following features into one sleek, sophisticated package.
Installation and System Setup 3M™ Digital WallDisplay Installation and System Setup Recommendation and Things to Consider Before Installing Location of Unit • Place near AC outlet. The AC power connection is located on the lower-left corner of the 3M Digital WallDisplay (the unit). The AC power cord supplied with the unit is 6 feet (2 m) long. • Service and screen replacement – The projection screen is removed from the side of the unit during replacement or service.
Installation and System Setup 3M™ Digital WallDisplay Installing the Wall Bracket Unpacking Wall Bracket and Hardware 1. Place the shipping container face up on the floor. 2. Open the end of the shipping container. 3. Slide the shipping tray partially out the container. 4. Locate and Remove the wall bracket and hardware. The hardware is taped to the wall bracket. Installation for a Hollow Wall-Drywall 1. Determine the desired location of the unit. Locate all wall studs in area. 2.
3M™ Digital WallDisplay Installation and System Setup Hanging the 3M Digital WallDisplay Unpacking the 3M Digital WallDisplay 1. Place the shipping container face up on the floor and open the end previous opened. 2. Slide the shipping tray out of the shipping container. 3. Remove the accessory box(es) from the top support. 4. Remove the top support. 5. Remove the plastic bag from the 3M Digital WallDisplay by lifting the top of the unit and pushing the bag towards the bottom of the unit.
Installation and System Setup 3M™ Digital WallDisplay Hanging on the Wall 1. If possible, position the 3M Digital WallDisplay and shipping tray in front of the wall where the bracket is located. Position the unit so that the projection arm is closest to the wall. 2. Clear the path from the unit to the wall where it will be hanging. Note: Most of the weight is at the projection head/ speakers end of the 3M Digital WallDisplay. 3.
Installation and System Setup 3M™ Digital WallDisplay System Setup It only takes a few minutes to connect the 3M Digital WallDisplay to your computer, VCR, DVD player, video conference unit, or other devices. The connection panel is located underneath the bottom right corner of the 3M Digital WallDisplay, under the Connection Panel Door. Press and release door to access connection panel.
Operation 3M™ Digital WallDisplay Operation Startup 1. Plug power cord into wall socket. 2. Flip on the Master Power Switch beneath the lower left corner of the 3M Digital WallDisplay, near the 3M label. This should stay on at all times. Now the 3M Digital WallDisplay is in standby mode. The large oval On/Off Button will be backlit amber after several seconds. 3. Press the On/Off Button in the center of the lower front panel.
3M™ Digital WallDisplay Operation Shutdown 1. Press the On/Off Button on the bottom center panel of the 3M Digital WallDisplay unit. 2. The lamp will turn off and the projector arm will return to its housing. The On/Off Button will flash red as the arm closes. Note: There is a 30-second reset period before the On/Off Button will function again. During this period, the On/Off Button will flash red. The fan will continue to run for approximately five minutes to cool the unit.
Remote Control Unit 3M™ Digital WallDisplay Remote Control Unit Features The remote control sensor is on the front lower panel of the 3M Digital WallDisplay unit. The distance between the sensor and remote control must be shorter than 4 meters (13 feet). The remote control unit has two keypads. The Forward keypad is above the flip-top cover. The Rear keypad is beneath the cover. The Trigger Button is underneath the front IR Sensor of the remote control unit and can be pressed easily with the index finger.
3M™ Digital WallDisplay Remote Control Unit Forward Keypad Power Press to turn the 3M Digital WallDisplay on/off. When power is turned on, the 3M Digital WallDisplay will automatically extend the projection arm and ignite the lamp. Mute Press to temporarily turn off the sound. Press again or press the Volume + or - buttons to restore sound. Disk Pad Press to: • control the computer’s mouse when using the Mouse function. • select menu items and adjust values in the onscreen menu system.
Remote Control Unit 3M™ Digital WallDisplay Rear Keypad Pointer Press to turn the pointing function on/off. A green dot will appear on the screen. The dot can be controlled by pressing the arrows on the Disk Pad. Volume Press the + button to increase or the - button to decrease the speaker loudness level. When the audio is muted, the Volume + or - buttons will also cancel the Mute function. Timer Press to turn the timing function on/off. The timer will display on the screen and begin to count down.
3M™ Digital WallDisplay Remote Control Unit Installing or Replacing Batteries 1. Push and slide the battery compartment tab in the direction shown, then lift it off. 2. Install two AAA batteries as indicated by the diagram inside the compartment. 3. Snap the battery compartment cover back on. Note: Avoid excessive heat and humidity. Do not mix old and new batteries or different types of batteries. © 3M 2005. All Rights Reserved.
Menu System 3M™ Digital WallDisplay Menu System Menu Navigation Most adjustments and settings are available in the main menu and sub-menus. To navigate and make adjustments, use the 3M Digital WallDisplay’s Menu Keypad button or the remote control’s Menu and Disk Pad buttons. Colorful—Bright Slider The Colorful—Bright slider adjusts the brightness, contrast, and color saturation levels simultaneously. Move the slider toward Colorful to achieve maximum color saturation and contrast.
3M™ Digital WallDisplay Menu System Warm—Cool Slider The Warm—Cool slider adjusts the color temperature. Move the slider toward Warm to achieve warmer, more reddish images. Move the slider toward Cool to achieve cooler, more bluish images. To adjust the Warm—Cool slider: 1. Open the menu system by pressing the remote control Menu button or any arrow on the Menu Keypad. 2. Select the Warm—Cool slider by pressing the up or down arrows on the remote control Disk Pad or Menu Keypad. 3.
Menu System 3M™ Digital WallDisplay Mute Menu Function The Mute menu function turns the sound on and off. To turn the Mute menu function on: 1. Open the menu system by pressing the remote control Menu button or any arrow on the Menu Keypad. 2. Select the Mute menu function by pressing the up or down arrows on the remote control Disk Pad or Menu Keypad. 3. Turn the Mute function on by pressing the left or right arrow of the Disk Pad or Menu Keypad. The sound will turn off. 4.
3M™ Digital WallDisplay Menu System Input Select Menu The Input Select menu defines the displayed video source. When Input Select menu is selected, the current video source is shown. The Input options are: Computer (VGA Input), DVI-D, S-Video, Comp. Video (RCA Video Input), and No Signal. An Input option is available to select when an active video source is connected to the 3M Digital WallDisplay input connection. To set the Input Select menu: 1.
Menu System 3M™ Digital WallDisplay Image Adj Sub-Menu The Image Adjustment sub-menu adjusts the projected image settings for the VGA and DVI-D inputs. Use the Vertical Position and Horizontal Position sliders to reposition an image if portions are not visible. Use the Phase and Sync sliders to eliminate vertical banding and noise. Vertical Position Adjusts the vertical position of the projected image. Horizontal Position Adjusts the horizontal position of the projected image.
Menu System 3M™ Digital WallDisplay Tools Sub-Menu The Tools sub-menu provides access to the following settings and tools: Onscreen Timer Allows you to set a timer and display it onscreen. Language Selects which language to use for onscreen commands. (Default language is English.) It cycles between English, German, Spanish, Italian, and French. Auto Shutoff Will automatically turn off the 3M Digital WallDisplay within the time desired. (Default time is 0 minutes.
Maintenance 3M™ Digital WallDisplay Maintenance General Maintenance For general cleaning of the screen and exterior of the 3M Digital WallDisplay, use a damp cloth or dry cleaning cloth such as the 3M High Performance Cleaning Cloth. Standard dry-erase cleaners may be used on the dry-eraseable screens, such as Sanford® Expo® Whiteboard Cleaner. Do not use other spray cleaners or solvents on any part of the 3M Digital WallDisplay.
Maintenance 3M™ Digital WallDisplay Lamp Replacement 1. Turn the power off and disconnect the power cord from the outlet. 2. Allow approximately 45 minutes for the lamp to cool, if necessary. 3. There are two indentations behind the top of the facade, near each end. Grasp facade plate at each indentation and pull out and down to remove plate. Facade 4. Loosen the self-contained screw at the upper righthand corner of the lamp housing door with a standard screwdriver. 5.
Maintenance 3M™ Digital WallDisplay 5a. Hold down this receptacle with your left thumb and (5b) pull connectors out of the receptacle with other hand. 5a 5b 6. Open the latch by moving the metal lever to the left. Lever 7. While holding the latch open, grasp the lamp cartridge and pull it straight out of the lamp compartment. 8. Holding the latch open, slide the new lamp cartridge into place. 9. Reconnect black wires to the receptacle. 10. Close the lamp housing door and tighten the screw.
3M™ Digital WallDisplay Maintenance 11. Align the slots and tabs of the right side of the facade and projection arm as shown, then snap firmly into place. 12. Align the slots and tabs of the left side of the facade and projection head as shown, then snap firmly into place. Note: You must hear or feel a distinctive snap to ensure facade is securely attached. Whenever the lamp is replaced, please reset the total lamp operating time. (Refer to next page.) © 3M 2005. All Rights Reserved.
Maintenance 3M™ Digital WallDisplay Resetting Lamp Hours Please do the following within 10 minutes of turning power on after you replace the lamp. 1. Press the Menu Keypad or the Menu button on the remote control and use the Disk Pad to scroll down to the Tools menu. 2. In the Tools menu, scroll down the pop-up list to Usage/Hrs to display the total operating time of the lamp. 3. Select Lamp Reset from the next pop-up list. 4. Select Exit.
3M™ Digital WallDisplay Maintenance Replacing ProjectionScreen Replacing the 3M Digital WallDisplay screen is very simple. 1. Turn off the 3M Digital WallDisplay and disconnect the power cord from the wall outlet. 2. Remove the right and left side bezels. There are two ways to remove it. Either snap it off or insert a screwdriver into the notch located on the sides of each bezel, near the top. The bezel will easily snap on and off for screen replacement. 3. Slide the screen straight out of the open side.
Maintenance 3M™ Digital WallDisplay Optical Engine Adjustment The optical engine needs to be aligned when the vertical or horizontal images do not cover the screen or are tilted. Note: Before continuing with this adjustment, move the arm assembly up and down to relieve any stress and see if the arm will realign itself and project an aligned image. 1. Locate the access door on the under side of the projection arm. 2. Slide the door release catch to the open position using the blade of a small screwdriver.
Maintenance 3M™ Digital WallDisplay 4. Loosen locking screw. Then use blade screwdriver on adjustment screw to move screen image from side to side if required. Tighten locking screw. 5. Locate adjustment screw for right side screen adjustment. Locate locking screw for right side adjustment. ���������� ���������������� ���������� ������������� ���� 6. Loosen locking screw. Then use blade screwdriver on adjustment screw to move right side screen image up and down if required. Tighten locking screw.
Maintenance 7. Locate adjustment screw for left side screen adjustment. Locate locking screw for left side adjustment. 3M™ Digital WallDisplay ��������� ������������� ��������� ���������������� ���� 8. Loosen locking screw. Then use blade screwdriver on adjustment screw to move left side screen image up and down if required. Tighten locking screw. Note: After making adjustments it may be necessary to perform the side to side adjustment to center the image properly. 9.
Troubleshooting 3M™ Digital WallDisplay Troubleshooting Common Problems and Solutions Symptom Cause Solution Power cannot be turned on. The power cord is disconnected. Insert the power cord into an AC socket. The Master Power Switch is not turned on. Turn on the Master Power Switch. The arm facade is not in place. Make sure the arm facade is in place. The desired input source is not selected. Press the remote control Input button to select a desired input source.
Troubleshooting 3M™ Digital WallDisplay Common Problems and Solutions Symptom Cause Solution Desired input source cannot be detected. The input source is not active. A signal must be present for the input to be selected. Connect an active input source to unit. The input device (e.g. computer, VHS player, etc.) is not turned on. Turn on input source The remote control is not facing the remote control sensor. Face the remote control toward the remote control sensor.
3M™ Digital WallDisplay Service Information Service Information Replacement Parts Description Part Number Power Cord (EU) 78-8131-0004-3 Power Cord (US) 78-8131-0005-0 Power Cord (UK) 78-8131-0003-5 Serial Mouse Cable 26-1015-0423-6 USB Cable 26-1015-0424-4 VGA Cable 26-1015-0425-1 DVI-D Cable 26-1015-0418-6 PC Audio Cable 26-1015-0420-2 S-Video Cable 26-1015-0422-8 Replacement Lamp 78-6969-9736-6 Remote Control Unit 78-8121-0330-3 Macintosh Adapter 26-1015-0419-4 3-Conductor Vid
Appendix 3M™ Digital WallDisplay Appendix 3M™ Digital WallDisplay Specifications Display Size 60" Diagonal viewing area Display Aspect Ratio 4:3 Display System Single Chip, DLP™ Texas Instruments technology DLP Chip Chip Diagonal Size 0.7 inch Number of Pixels 1024 x 768 pixels Color 24-bit full color Contrast Ratio 150:1 Dimensions 47.6" H x 53.2" W x 7.0" D (1208 mm x 1350 mm x 179 mm) Weight Approx. 85 lbs. Video Compatibility NTSC, NTSC 4.
Appendix 3M™ Digital WallDisplay Input/Output Signal Specifications Computer Video Signal Analog 0.7Vp-p, 75 Ohms termination (positive polarity) Horizontal Sync Signal TTL Level (positive/negative polarity) Vertical Sync Signal TTL Level (positive/negative polarity) Audio Input Signal 200m Vrms, 20k Ohms (Max 3.0Vp-p) Audio Output Signal 0~200m Vrms, 1k Ohms S-Video Video Luminance Signal 1.0Vp-p, 75 Ohms Chrominance Signal 0.286Vp-p (color burst), 75 Ohms Video Signal 1.
Important Notice All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use.