Instructions / Assembly

ManualsBrands3M ManualsKitchenAqua-Pure Under Sink Dedicated Faucet Water Filtration System AP-DWS1000, 5583101, 0.5 um (1 Per Case)

AP-DWS1000 Drinking Water Appliance Owner’s Manual

Installation Precautions

6888931 0701

Installation and

Operating Instructions

• Do not use with water that is microbiologically

unsafe or of unknown quality without adequate

disinfection before or after the system.

• Installation must comply with state and local

plumbing codes.

• Systems certified for cyst reduction may be

used on disinfected water that may contain

filterable cysts.

• System must be protected from freezing. Drain

filter when room temperature drops below

40°F (4.4°C).

• Do not install on line pressure above 125 psi

(862 kPa).

• Do not install on hot water line. Maximum

temperature allowed is 100°F (38°C).

• The filter must be installed with the inlet and

outlet ports as labeled. Make sure not to

reverse connections.

• Do not use wicking or sealer for fitting connections

into head of filter. Use Teflon

tape for connections.

• Do not use torch or other high temperature

sources near filter or plastic cartridge.

• Do not install near electric wires or water pipes

which will be in the path of drill when selecting

the position to mount bracket.

• Do not install in direct sunlight.

• Allow a minimum of 2” (5cm) clear space

under filter to facilitate cartridge change.

• Mount filter in such a position as to prevent it

from being struck by other items.

Teflon is a registered trademark of E.I. DuPont.

Summary of content (11 pages)

PAGE 1
6888931 0701 Installation and Operating Instructions AP-DWS1000 Drinking Water Appliance Owner’s Manual Installation Precautions • Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. • Installation must comply with state and local plumbing codes. • • • • • The filter must be installed with the inlet and outlet ports as labeled. Make sure not to reverse connections.
PAGE 2
Specifications: Inlet/Outlet Size: 1/4” Tube with Quick Connect Fittings Flow Rate: 0.6 gpm (2.3 lpm) Temperature Range: 40-100°F (4.4-38°C) Pressure Range: 30-125 psi (207-862 kPa) Capacity: 625 gallons (2,366 liters) Weight: 7 lbs (3.
PAGE 3
1. Install Drinking Water System Faucet (Refer to Figure 4, Page 7) Note: The drinking water system faucet should be located on a flat surface, conveniently located near the sink, so that it empties into the sink. Most sinks have pre-drilled holes designated for sprayers, soap dispensers, and other accessories. If your sink does not have an extra hole, then a 9/16” diameter hole must be drilled. Warning: Porcelain, enamel, and ceramic sinks require special procedures for drilling holes.
PAGE 4
3. Install Feedwater Valve (Refer to Figure 5, Page 7) Warning: Make sure cold water valve is turned off under the sink. A. Most sinks use 3/8” copper tubing. Connect the saddle valve as shown in Figure 5, Page 7. The back saddle bracket can be reversed for smaller pipe sizes (7/16” to 1/2”). Tighten screws evenly and firmly, brackets should be parallel. B. To pierce soft copper tubing, turn handle to the right several times until it stops. The valve is now closed.
PAGE 5
Special Section Procedure For Drilling Hole Through Porcelain/Enamel/Ceramic Sinks With Sheet Metal or Cast Iron Base Recommended tools: Variable Speed Drill Porcelain Cutter Tool Set (9/16” Size) Plumber’s Putty Note: It is important to understand this procedure. 1. The glassy layer of porcelain/enamel/ceramic must be scored through to the metal base creating a disk. 2. This disc must be removed while protecting the surrounding decorative coating against chipping or fracturing. 3.
PAGE 6
Quick Connect Guide (Figure 1) ‘Push-In’ Tubing Connector (Quick Connect Fittings) This product is outfitted with user friendly ‘Push In’ connectors. Proper use of the connectors is shown in the diagrams. It is most important that the tubing selected for use with these connectors be of high quality, exact size and roundness, and with no surface nicks or scratches. If it is necessary to cut the tubing, use a plastic tubing cutter or sharp razor knife. Make a clean square cut.
PAGE 7
Installation Overview (Figure 3) 1 Standard Installation Overview 6 1. Install DWS Faucet 2. Mount System 1 3. Install Feedwater Valve 4. Making Connections Stainless Bezel Rubber Washer Countertop 5. Test System 6. Flush Filter 2 Plastic Backing Spacer Star Washer Hex Nut 3 5 4 3 6 2 4 17" (43.
PAGE 8
Install Drinking Water System Faucet (Figure 4) Stainless Bezel Rubber Washer A Stainless Bezel Stainless Bezel Stainless Bezel Rubber Washer Rubber Washer Rubber Washer Countertop Countertop Countertop B C D Plastic Backing Spacer Plastic Backing Spacer Star Washer Hex Nut Star Washer Hex Nut Install Feedwater Valve (Figure 5) A B 7 C
PAGE 9
Making Connections (Figure 6) B A FROM FEEDWATER VALVE FROM DWS FAUCET C FILTER 1 FILTER 2 8
PAGE 10
Cartridge Change Instructions (Refer to Corresponding Diagrams Below) 1. Turn water supply off at saddle valve or at undersink cold water line and remove protective shroud from bracket. 2. Reset shutoff meter by pushing in knob and turning to the right until the arrow on the top of the meter body is approximately lined up to 625 gallons. (The shutoff meter will shut water pressure to the faucet down when the preset number of gallons are dispensed.
PAGE 11
© 2002 CUNO Incorporated CUNO Incorporated 400 Research Parkway Meriden, CT 06450 U.S.A. Toll Free: 1-800-222-7880 Worldwide: 203-237-5541 Fax: 203-238-8701 www.aquapure.com • www.cuno.