3M™ Multi-Touch Display User Guide For the Product Line: C2167PW Read and understand all safety information contained in this document before using this product. 3M Touch Systems, Inc.
3M™ Multi-Touch Display User Guide 2 The information in this document is subject to change without notice. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of 3M Touch Systems, Inc. 3M may have patents or pending patent applications, trademarks, copyrights, or other intellectual property rights covering subject matter in this document.
M™ Multi-Touch Display User Guide 3 Contents Chapter 1 Introduction Overview ....................................................................................................................4 Multi-Touch Display Features....................................................................................4 Touch Screen for Multi-Touch Displays ....................................................................5 Important Safety Information .............................................................
3M™ Multi-Touch Display User Guide 4 CHAPTER 1 Introduction Overview Congratulations on the purchase of your 3M™ Multi-Touch Chassis Display. This guide describes how to set up your Multi-Touch Chassis Display. The 3M™ Multi-Touch Chassis Displays, available in 21.5 inch display sizes, are an ideal solution for kiosk applications that require the modern flat front surface design and Multi touch gesture performance found in popular smart phone and tablet devices today.
3M™ Multi-Touch Display User Guide Horizontal frequency range: 21.5 inch display -- 31.47 ~ 82.3 kHz Vertical frequency range: 21.5 inch displays -- 56 ~ 75 Hz high refresh rate Pixel pitch 21.5 inch display -- 0.24795mm x 0.24795mm Auto adjustment function Multilingual OSD user controls VESA mount 21.
3M™ Multi-Touch Display User Guide 6 DANGER To avoid the risk of fire and/or explosion which will cause serious injury or death: Do not install or use this product in a hazardous location. WARNING To reduce the risk of fire and/or explosion or electric shock which could cause death or serious injury and/or property damage: Do not use this product in any outdoor environment unless NEMA standards (or similar standards such as IP rating) are followed.
3M™ Multi-Touch Display User Guide 7 CAUTION using any solvents. It is important to avoid using any caustic chemicals on the touch sensor. To avoid possible environmental contamination which may cause minor or moderate injury: The LCD lamps inside this product contain mercury (Hg). This product may contain other electronic waste that can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal laws.
3M™ Multi-Touch Display User Guide 8 Maintaining Your Touch Display To maintain your display and keep your display operating at peak performance: Keep your display and touch sensor clean. Adjust the display video controls. Do not install the display in a place where ventilation may be hindered. Always maintain adequate ventilation to protect the display from overheating and to promote reliable and continued operation. Touch Sensor Care and Cleaning The touch sensor requires very little maintenance.
3M™ Multi-Touch Display User Guide You can contact 3M Touch Systems, Inc. Technical Support (US only -- Eastern Standard Time) by calling the hot line, sending email or a fax. Technical Support Hot Line: 978-659-9200 Technical Support Fax: 978-659-9400 Toll Free: 1-866-407-6666 (Option 3) Email: US-TS-techsupport@mmm.com Contact 3M Touch Systems Contact information for all offices can be found on our website at: http://www.3m.com/touch/ 3M Touch Systems, Inc.
3M™ Multi-Touch Display User Guide 10 CHAPTER 2 Setting Up Your Multi-Touch Chassis Display This chapter describes how to set up your 3M Touch Systems Multi-Touch Chassis Display. You need to complete the following tasks: Unpack the components Connect the video cable, touch display USB cables, and power cable Power on the display and test your setup If you are not running Windows® 7 (or Tablet PC), install software from the enclosed CD.
3M™ Multi-Touch Display User Guide Quick Start Guide 11 Touch Driver CD Multi-Touch Chassis Display Dimensions C2167PW Attaching the Side Brackets Depending on your mounting scheme, you may use the side brackets to mount your displays onto your wall or device. Find a suitable location for attaching side brackets. Note: You will need a screwdriver to attach the side brackets. Your touch monitor includes four side brackets (and eight screws, M4x8).
3M™ Multi-Touch Display User Guide 12 Connecting the Display To setup this display, please refer to the following figures and procedures. Be sure all equipment is turned off. Connect the DC adapter to the power connector (DC IN) on the monitor and the other end into an electrical outlet. Connect the D-SUB cable from the display’s VGA input connector to the D-SUB connector of your host computer and tighten the screws.
3M™ Multi-Touch Display User Guide 13 Display Mode 640 x 480 720 x 400 800 x 600 832 x 624 1024 x 768 1152 x 864 1280 x 960 1280 x 1024 1440 x 900 1680 x 1050 1920 x 1080 Refresh Rate (Hz) 60, 66, 72, 75 70 56, 60, 72, 75 75 60, 70, 75 75 60 60, 75 60, 75 60 60 Configuring the Display Settings After you connect your Multi-Touch Chassis Display and turn on your computer, you may need to configure one or more of these display settings.
3M™ Multi-Touch Display User Guide 14 How to Use the OSD Menus 1. Press the MENU button to pop up the on-screen menu and press Up or Down button to select among the five functions in the main menus. 2. Choose the adjustment items by pressing the Select button. 3. Adjust the value of the adjustment items by pressing the Up or Down button. 4. With the OSD menu on screen, press the Menu button to return main menu or exit OSD. 5.
3M™ Multi-Touch Display User Guide 15 Brightness Auto Adjust Left/Right Up/Down Horizontal size Fine OSD Left/Right OSD Up/Down OSD Time out OSD Language The monitor backlight level control. Fine-tune the image to full screen automatically. Moving screen image horizontal position to left or right. Moving screen image vertical position to up or down. The screen image horizontal dot clock adjustment. The screen image pixel phase adjustment. Moving OSD menu horizontal position to left or right.
3M™ Multi-Touch Display User Guide 16 Image has vertical flickering line bars. Use “Fine” to make an adjustment. Check and reconfigure the display mode of the vertical refresh rate of your graphic card to make it compatible with the LCD display. Image is unstable and flickering Use “Fine” to make an adjustment. Image is scrolling Check and make sure the VGA/DVI signal cable (or adapter) is securely connected.
3M™ Multi-Touch Display User Guide 17 CHAPTER 4 Enabling Your Multi-Touch Chassis Display Windows™ 7 USB Compatibility 3M multi-touch technology works seamlessly with the Windows™ 7 operating system. The Multi-Touch display supports USB HID for direct communication. The Multi-Touch Chassis Display leverages all the multi-touch functionality that is native to Windows™ 7. Plug the display in to a system running Windows™ 7 and you’ll quickly enter the world of true multi-touch functionality.
3M™ Multi-Touch Display User Guide 18 For non-Windows 7 operating system users this document provides the communication protocol necessary to talk directly with the electronics. This enables software developers using other operating systems such as Microsoft Windows™ Vista or Linux® to write their own drivers and achieve the same multi-touch results. Multi-Touch Application Support Remember not all applications are multi-touch ready -- Multi-touch behavior is a function of YOUR application.
3M™ Multi-Touch Display User Guide 19 CHAPTER 5 Regulatory Information Regulatory Agency Approvals Your product complies with the following regulatory standards: FCC-B CE UL RoHS/WEEE directives This equipment has been tested and found to comply within limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in residential installations.
3M™ Multi-Touch Display User Guide 20 This device complies with Part 15 of the FCC rules: Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Warning To assure continued FCC compliance, the user must use grounded power supply cord and the provided shielded video interface cable with bonded ferrite cores.
