Operator’s Guide PocketProjector 3M 160 ™ 3
English 3M™ Pocket Projector 160 2 © 2010 3M. All Rights Reserved.
English 3M™ Pocket Projector 160 Contents Intended Use Statement �������������������������������������������������������������������������� 4 Safety Information ����������������������������������������������������������������������������������� 4 Safety Labels ������������������������������������������������������������������������������������������ 7 Package Contents ����������������������������������������������������������������������������������� 8 Parts �����������������������������������������������
English 3M™ Pocket Projector 160 Intended Use Statement The 3M Pocket Projector 160 is designed to operate with the 3M specified battery and 3M power adapter in normal office or home environments. • 0˚–35˚C (32˚–95˚F) • 10–80% RH (without condensation) • 0–1829 m (0–6000 feet) above sea level The ambient operating environment should be free of airborne smoke, grease, oil and other contaminants that can affect the operation or performance of the projector.
English 3M™ Pocket Projector 160 m Warning To reduce the risk associated with hazardous voltage: • Do not modify this product in any way. Use only 3M approved replacement components. • Do not attempt to service this projector other than battery replacement. There are no user-serviceable parts other than the battery. Service to be performed only by a 3M authorized service provider using 3M approved system components. • Do not use the wall power supply in a wet environment.
English 3M™ Pocket Projector 160 m Warning To reduce the risk associated with fire and explosion, battery leakage or overheating: • Do not immerse the battery in water or allow it to get wet. • Do not reverse the positive(+) and negative(-) terminals. • Do not connect the battery directly to a wall outlet. Use only the 3M specified wall charger or automobile charger. • Do not strike, throw or subject the battery to physical shock. • Do not pierce the battery or break it open.
English 3M™ Pocket Projector 160 Safety Labels XXXXXXXX LITHIUM ION BATTERY Model No. LIN370-001 28.86Wh (11.1V 2600mAh x 3) P/N 78-6972-0026-5 m Warning • Use a specified charger. • Do not throw the battery into fire or heat. • Do not short-circuit the battery terminals. • Do not disassemble the battery. Charging Specification Standard Charge 11.1V/1.3A Cut Off Voltage 8.5V Max Charge 12.3V/1.
English 3M™ Pocket Projector 160 Package Contents 1 3M Pocket Projector 160 2 Table-Top Tripod 3 Rechargeable Battery 4 Carrying Pouch 5 Outlet Adapters (4) 6 Power Adapter 7 AV Adapters (3) 8 Product Warranty and Safety Guide 9 Quick Start Guide 10 AV Cable 11 VGA-Audio Cable 2 1 4 3 6 5 8 9 7 10 11 8 © 2010 3M. All Rights Reserved.
English 3M™ Pocket Projector 160 Parts 1 Power Button 2 Mute Button 3 Volume Down Button 4 Volume Up Button 5 Battery Status Button 6 Status Indicator 7 Focus Wheel 8 Lens 9 Speaker 10 Flip Stand 11 Tripod Socket 12 Battery 13 Battery Latch 14 Earphone jack 15 VGA-A/V Input 16 DC Power Input 1 4 2 5 3 6 7 9 8 10 9 11 12 14 © 2010 3M. All Rights Reserved.
English 3M™ Pocket Projector 160 Getting Started Install Battery The 3M Pocket Projector 160 comes with a rechargeable battery. The battery should be fully charged before using the projector with the battery. To install the battery: point the contacts on the battery toward the contacts on the projector, insert the end farthest from the battery latch first, then push down until the battery clicks into place.
English 3M™ Pocket Projector 160 Power Adapter The power adapter is used to charge the battery or power the projector. There are four outlet adapters to give you the flexibility to power the 3M 160 projector in most countries. You can also power the projector with the 3M 160 projector car charger, available separately. Installing an Outlet Adapter onto the Power Adapter 1 Select the outlet adapter that will plug into your wall outlet.
English 3M™ Pocket Projector 160 Charge the Battery The rechargeable battery gives you up to two hours of battery life. When the battery needs to be charged, the status indicator will flash red. The battery should be fully charged before using the projector. Charge the battery by connecting the power adapter to the projector. 1 Turn the projector power off. 2 Connect the power adapter to the projector’s DC input. 3 Connect the other end of the power adapter into the electrical outlet.
Battery Charging Notes: • If the projector power is off, allow three hours for the battery to fully recharge. If the projector power is on, the battery will take longer to charge. • The battery has a lifespan and ages every time it is fully charged and discharged. The battery will gradually lose charge capacity as it ages. Therefore, as the battery ages the battery life will decrease. Battery Maintenance Tips: • Remove the battery when the projector will not be used for one week or longer.
English 3M™ Pocket Projector 160 Making Connections The 3M Pocket Projector 160 will display informational icons depending on the input device and signal being detected. The 3M 160 was designed to operate with the 3M VGA and AV cables only. Connecting to a Composite Video Device Use the AV cable to input video from camcorders, digital cameras, DVD players and digital media players into the VGA-AV input on the projector. 1 Connect the AV cable to the projector’s VGA-AV input.
Connecting to a Component Video Device For component video input, you must purchase the optional 3M 160 Component AV Cable [3M part number xx-xxxx-xxxx-x]. This cable sends a higher quality video signal for the best possible image. 1 Connect the component AV cable to the projector’s VGA-AV input. 2 Connect the other end of the AV cable to the video device’s audio and video outputs. Important Note: There are two red connectors on the Component AV cable.
English 3M™ Pocket Projector 160 Connecting to a Computer Use the VGA-audio cable to connect the projector to desktop computers, laptop computers, ultra-portable computers and some personal digital assistants (PDAs). The projector supports VGA, SVGA, XGA, and WXGA resolutions. For best results, set the computer’s resolution to SVGA (800x600). 1 Connect the VGA cable to the 3M Pocket Projector 160. 2 Connect the VGA cable to the computer’s video and audio outputs.
Basic Operating Instructions Powering On Press and hold the power button for three seconds. Release the power button when the projector begins to project an image and the status indicator turns green. Tip: The video output on some devices is turned off by default. Please refer to the device’s documentation for details on enabling the video output. Powering Off Press and hold the power button for three seconds. Release the power button when the projected image is gone.
English 3M™ Pocket Projector 160 Status Indicator Light The status indicator light provides information about the projector’s state. Status Indicator Light Flashes green three times Blank Flashes green Solid green Solid amber Flashes amber Flashes red twice and pauses then repeats Meaning A new power source is connected to the projector and the projector is ready to be powered on. Projector is off.
English 3M™ Pocket Projector 160 Adjusting Image Size The 3M 160 Projector can project a diagonal image of 10 to 60 inches (254–1524 mm). Refer to the chart for associated dimensions. Diagonal Size Image Width Image Height Projectorto-Screen Distance 14 in (35.56 cm) 11 1/4 in (28.4 cm) 8 3/8 in (21.3 cm) 11 3/4 in (29.9 cm) 20 in (50.8 cm) 16 in (40.6 cm) 12 in (30.5 cm) 16 3/4 in (42.7 cm) 26 in (66.04 cm) 20 3/4 in (52.8 cm) 15 5/8 in (39.6 cm) 21 7/8 in (55.5 cm) 32 in (81.
English 3M™ Pocket Projector 160 Adjusting the Volume Press the Volume Up or Volume Down button to adjust the sound. A volume bar will appear on the screen to help you set the volume level. Muting the Volume Press the MUTE button to mute the volume. An icon will appear on the screen to indicate the current setting. To restore the volume, press the MUTE button again.
English 3M™ Pocket Projector 160 Attaching the Tripod The projector includes a table-top tripod that mounts to the bottom of the projector. Tip: The 3M 160 Projector will attach to most camera tripods. Cleaning the Projector 1 Turn off the projector and disconnect power and other cables. 2 Use a soft cloth, such as the 3M™ High Performance Cleaning Cloth, to wipe off dust. If the dust is difficult to remove, dampen the cloth with clean water and then wipe the projector clean.
English 3M™ Pocket Projector 160 Troubleshooting The projector will not turn on. • The battery is not properly installed, or the power adapter is not connected to the projector and a working wall outlet. Test the electrical outlet by plugging another electrical device (like a radio) into the wall outlet to confirm that the wall outlet works. • The battery is installed in the wrong orientation. See “Install Battery” on page 10. • Attempt to remove and replace the battery.
• The speakers may make noise when the component AV cable is not correctly connected to the video device. There are two red connectors on the component AV cable. One is for the right audio channel and the other is for the Pr component video signal. If these connectors are switched, the projected image will appear green and an abnormal noise will come from the right speaker. My video device is connected to the projector but the projector will not display the video.
English 3M™ Pocket Projector 160 Specifications Projector Description Imager Specification Technology LCOS Size 9.4 mm (0.37") Resolution SVGA 800 x 600 Pixels Aspect Ratio 4:3 Projection Distance 8.4 in. – 50.4 in. (213–1280 mm) Image Size 10 in. – 60 in. Diagonal (254–1524 mm) Throw Ratio (Diagonal: Distance) 1:0.84 Lens Offset 1:1 (none) Inputs DC-in, AV-in (inc.
English 3M™ Pocket Projector 160 LIN370-001 Rechargeable Lithium-Ion Battery Description Specification Type (LIN370-001) Rechargeable Lithium-Ion Battery Rated Capacity 11.1 V 2600 mAh, 28.9 Wh Dimensions 81.5 x 64 x 23 mm Important Note: Do not throw battery into trash.
English 3M™ Pocket Projector 160 Limited Warranty This warranty applies to the continental US only. The warranty terms, conditions, remedy and limitation may vary in other countries. Contact your local 3M Company for warranty information. • The 3M™ Pocket Projector 160 (the “3M product”) is warranted to be free from defects in material or manufacture for a period of 1 year from the date of purchase.
c. The air intake and exhaust vent must be clear of obstructions. Inadequate air ventilation will cause the 3M product to malfunction or will cause damage to the 3M product which will void the warranty. d. This warranty does not cover any additional costs including, but not limited to, those associated with removal, cleaning or installation of the 3M product, adjustments, (mechanical or electronic) made to the 3M product. e. This warranty covers only normal use of the product.
English 3M™ Pocket Projector 160 • The exchanged 3M product or part may be new or previously refurbished to the 3M standard of quality, and at 3M’s option, the replacement may be another model of like kind and quality. • 3M’s liability for replacement of the warranted 3M product or part will not exceed the original retail selling price of the 3M product. Exchange or replacement products or parts assume the remaining warranty period of the product covered by this limited warranty.
English 3M™ Pocket Projector 160 WEEE Statement The following information is only for EU-members States: The mark shown to the right is in compliance with Waste Electrical and Electronic Equipment Directive 2002/96/ EC (WEEE). The mark indicates the requirement NOT to dispose the equipment as unsorted municipal waste, but use the return and collection systems according to local law. RoHS Statement 3M Mobile Interactive Solutions can provide RoHS certification for products meeting the RoHS directive.
3M is a trademark of 3M Company. 3 Mobile Interactive Solutions 3M Austin Center 6801 River Place Blvd. Austin, TX 78726-9000 866-631-1656 www.3M.com/meetings meetings@mmm.com Please Recycle. Printed in China. © 3M 2010. All Rights Reserved.
