3M™ Connected Safety Hub and Docking Station User Instructions IMPORTANT: Read all instructions and warnings before using. Keep these User Instructions for reference. If you have questions regarding these products, contact 3M Technical Service. For technical help, contact 1 (800) 243-4630 and select Connected Safety Personal Safety Division 3M Center, Building 235-2W-70 St. Paul, MN 55144-1000 © 3M 2019. All rights reserved. 3M is a trademark of 3M Company and affiliates. Used under license in Canada.
• • • • !!! IMPORTANT READ FIRST !!! Read and understand the contents of these User Instructions prior to use, including all warnings and advisories. This system is for professional occupational use only. The 3M™ Connected Safety Hub is not designed or approved to meet intrinsic safety standards. Follow all 3M Personal Protective Equipment (PPE) User Instructions for devices that may be used with this system. Contents Foreword ...............................................................................
Foreword List of Warnings within these User Instructions WARNING The 3M™ Connected Safety components used in this system are not intrinsically safe. Do not use in flammable or explosive atmospheres. Doing so may result in serious injury or death. 2. Worker alerts generated by the connected system should not to be used in place of existing safety program policies, practices and procedures. They are designed to be supplemental to an established safety program.
Limitations of Use WARNING The 3M™ Connected Safety components used in this system are not intrinsically safe. Do not use in flammable or explosive atmospheres. Doing so may result in serious injury or death. The 3M™ Connected Safety Hub can only be used with approved 3M™ Connected PPE devices. Refer to and follow the User Instructions provided with PPE that may be used with this system for all appropriate use, operation, care, inspection and maintenance guidance of those devices.
Installation Unpacking Inspect the package contents for shipping damage and ensure all components are present. The product should be inspected before each use following the procedures in the Inspection section of these User Instructions. Battery Please read, understand, and follow all safety information contained in these instructions prior to the use of the Safety Hub battery pack. Retain these instructions for future reference. 1. 2. 3.
2. Remove Safety Hub battery cover. 3. Place the hub face down on a flat surface with the battery compartment opening upwardfacing. 4. Insert the battery with the label facing up to properly seat the pack (Figure 1). Figure 1 5. Replace the battery cover and tighten screws to secure in place. A size #1 Phillips head screwdriver will be necessary to secure the battery cover.
Docking Station WARNING Do not disassemble, modify or service this device. The Docking Station contains no user serviceable parts except for the wall mount hardware. System components requiring any necessary repairs or service would need to be sent into an authorized 3M service center. The 3M™ Connected Safety Hub Docking Station provides a power source for Safety Hubs to charge and an Ethernet port to upload data that may not have already been sent to the Connected Safety cloud application via Wi-Fi.
Charging Safety Hub housings should be cleaned or decontaminated as necessary to remove any dirt or debris that may be present before placing in the Docking Station. Up to four hubs can be placed in a single dock. A full charge cycle for the hub batteries can take up to 4 hours. Charge only using approved 3M equipment. Do not charge outside of the operating temperature range. NOTICE: Always disconnect Safety Hub Docking Station from power prior to cleaning contacts.
Operation WARNING Worker alerts generated by the connected system should not to be used in place of existing safety program policies, practices and procedures. They are designed to be supplemental to an established safety program. To reduce the risks associated with exposure to workplace hazards which, if not avoided, could result in serious injury or death, users should follow all Safety Supervisor direction on how to respond to alerts that may be experienced.
Safety Hub LED’s LED’s are present on the Safety Hub to provide visual indication to users of various operational states both when a hub is docked and undocked.
Worker Alerts WARNING Worker alerts generated by the connected system should not to be used in place of existing safety program policies, practices and procedures. They are designed to be supplemental to an established safety program. To reduce the risks associated with exposure to workplace hazards which, if not avoided, could result in serious injury or death, users should follow all Safety Supervisor direction on how to respond to alerts that may be experienced.
Donning Instructions 3M™ Safety Hub Holster HUB-1-HLST-CX holds the hub when it goes into use. The holster’s metal clip allows it to be attached to a PAPR belt or backpack mounting option. Always don the Safety Hub where the device can be easily seen, and the user can feel the vibratory feedback when there is an active alert. Perform a pre-use visual inspection to ensure there are no visibly damaged external components of the connected system.
Inspection and Maintenance Refer to the 3M PPE User Instructions for proper use, operation, care, inspection and maintenance of those devices used with this system. Always inspect the Connected Sensor before and after each use for signs of damage or wear including dents, cracks, color changes, chalking, fading, flaking and penetration. If any signs of wear and/or damage are observed, remove the sensor module from use and replace as appropriate.
Regulatory FCC ID: DGFPSDHUB1CX IC: 458A-PSDHUB1CX FCC/ISED Compliance This device complies with Part 15 of the FCC Rules and with ISED’s license-exempt RSS's. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The following is required for Innovation, Science, and Economic Development Canada.
This system is subject to European WEEE Directive 2002/96/EC. This product contains electrical and electronic components and must not be disposed of using standard refuse collection. Please consult local directives for disposal of electrical and electronic equipment.
Terms of Service and License Terms of Service and License for 3M™ Versaflo™ Connected Powered Air Purifying Respirator, 3M™ Connected Safety Hub, and 3M™ Versaflo™ Connected Sensor Software This Agreement is 3M’s Terms of Service and License that governs its relationship among you, the principal on whose behalf you are authorized to act (the “Principal,” with you and the Principal collectively being the “User”), and “3M” (through 3M Company or its Affiliate(s) in the local country in which Software is provi
3. Permitted Use and License 3.1. 3M hereby grants to User a worldwide, limited, non-exclusive, and non-transferable license to access and use the Software in accordance with this Agreement. The Software is only licensed for use with specified Licensorsupplied systems for the Software and, if applicable, in accordance with any authentication credentials provided by 3M to the User. User agrees not to use, or permit others to use the Software for any purposes beyond the scope of this Agreement.
5.1. 3M may, at its sole discretion, use commercially reasonable efforts to provide support services for the Software to User; however, unless specifically provided for in a separate agreement between 3M and User, in no event, shall 3M be obligated to provide support services to the User. User expressly acknowledges that 3M does not guarantee a specific response time to requests for support services. 6. Warranty 6.1. USE OF THE SOFTWARE IS AT USER’S SOLE RISK.
9. User Data and 3M’s Use of User Data 9.1. User acknowledges, agrees and understands that, in connection with 3M providing User with access to and use of the Software, information resulting from User’s use of the Software may be transmitted to 3M.
appropriately used, disclosed and protected according to the 3M Connected Safety System Data Processing Agreement, which can be requested from 3M or accessed at: https://login.connectedsafety.3m.com/TermsAndConditions/DataProcessingAgreement. 9.
with applicable laws and regulations, including but not limited to those governing the collection, storage and use of personal information. User is solely responsible for establishing and maintaining policies, procedures, and thirdparty agreements relating to such information (including relating to collection, storage and use) as required by law. 11.8. Prior Agreement. This Agreement supersedes and replaces any and all prior agreements for the Software previously executed by the User. 11.9. Amendments.
which may incur in connection with a breach of the clauses (a) to (f) or a breach of PIPEDA or other related provincial legislation concerning the protection of personal information by 3M, its officers, employees, agents and subcontractors. Open Source Notices Open Source Notices for the 3M™ Versaflo™ Connected Powered Air Purifying Respirator, 3M™ Connected Safety Hub, and 3M™ Versaflo™ Connected Sensor Software can be found here: https://login.connectedsafety.3m.
