User Instructions April 2020 3M™ Scott™ Vision C5 Full Facepiece Electronics 3M™ Scott™ Vision C5 Full Facepiece Electronics UserInstructions for the RadioDirectInterface(RDI) and BatteryCharger for the 3MScottVisionC5FullFacepiece i IMPORTANT NOTE Before use, the wearer must read and understand these User Instructions. Keep these User Instructions for reference.
595406-01 Rev B Regulatory & Safety Information i IMPORTANT NOTE Read all of the regulatory and safety information before use. This facepiece and its components are intended to be used with 3M Scott respirators, which may support human life in hazardous atmospheres. Failure to carefully follow these instructions and warnings and the instructions and warnings provided with your 3M Scott respirator may result in serious injury or death.
This equipment is listed as intrinsically safe by CSA Group to CSA 60079-11 for Canada and UL 60079-11 for the USA for use in the following hazardous locations: Ex ia IIB T3 Ga (Canada) Class I Zone 0 AEx ia IIB T3 Ga (USA) Cet équipement est classé comme étant sécuritaire de façon intrinsèque par le CSA Group en vertu de la norme CSA 60079-11 au Canada et UL 60079-11 aux États-Unis pour usage dans les emplacements dangereux suivants: Ex ia IIB T3 Ga (Canada) Catégorie I Zone 0 AEx ia IIB T3 Ga (É.-U.
To maintain the Intrinsic Safety Listing, regularly inspect this equipment per the inspection procedures provided with the equipment. Do not tamper with or substitute components in any manner. Charge the battery only with the approved battery charger and only in accordance with the charging instructions provided. Pour préserver la classification de sécurité intrinsèque, cet équipement doit être régulièrement inspecté selon les procédures d'inspection opérationnelle provenant du manufacturier.
Approved battery charger: 201718-XX Power Supply (Low-power): 31004245 Power Supply (High-power): 31003969 Chargeur à pile approuvé: 201718-XX Power Supply (Low-power): 31004245 Power Supply (High-power): 31003969 Battery To maintain the Intrinsic Safety Listing, regularly inspect this equipment per the inspection procedures provided with the equipment. Do not tamper with or substitute components in any manner.
Warning: Modifications to this device shall not be made without the written consent of 3M, Company. Unauthorized modifications may void the authority granted under Federal Communication Rules permitting the operation of this device. Battery Storage When the battery is not in use, charge the battery until it is full, and then store the battery in a cool place. Ensure that the battery is charged bi-annually. Do not leave the battery on prolonged charge when not in use.
Improper use of this equipment may result in serious injury or death. Improper use includes, but is not limited to, use without adequate training, disregard of the warnings and instructions contained herein, use of the equipment for purposes not included in these instructions, and failure to inspect and maintain the equipment. Apply only the instructions offered within this manual. Maintenance procedures beyond the scope of this manual must not be performed.
This equipment is designed and intended to function properly in reasonable/ordinary firefighting conditions. The functionality of this equipment may be compromised by extreme fire conditions. Training is required before use of this equipment. Use this equipment only if you have been trained in its use and only in conjunction with an organized respiratory protection program. Do not use this equipment for purposes other than those authorized by your respiratory protection program.
• • ! Do not store batteries haphazardly in a box or drawer where they may short-circuit each other or where other metal objects may short-circuit them. Do not attempt to charge a non-rechargeable or non-3M-approved battery using the battery charger. WARNING To reduce the risks associated with fire, explosion, and exposure to battery chemicals, which, if not avoided, could result in serious injury or death: • Use only a 3M-approved battery.
Take care to prevent snagging the facepiece, which may pull the facepiece away from the face. ! WARNING To reduce the risks associated with fire and exposure to contaminants, which, if not avoided, could result in serious injury or death: Do not charge batteries not approved for use with the 3M battery charger unit.
! WARNING To reduce the risks associated with fire, explosion, exposure to contaminants, and oxygendeficient atmospheres, which, if not avoided, may result in serious injury or death. Follow the regular operational inspection procedures exactly. If there are any operational malfunctions, remove the respirator from service and tag for repair by authorized personnel.
The Universal Expansion Port (UEP) on the RDI is used for communicating with other peripheral devices such as the Integrated Bone Conduction Headset 1. The UEP includes a high-speed bus and power supply. Integrated Bone Conduction Headset (BCH) enhances voice communication clarityby leveraging the transmission of sound through the skullusing transducer headphones that sit on the wearer's temples.
3M Scott Vision C5 Full Facepiece with Electronics 1 3M Scott Vision C5 Full Facepiece 13
Bone Conduction Headset (BCH) Bone Conduction Headset (BCH) Control Module Communications Module Battery Facepiece Power Button and Battery Compartment Power Button Battery Compartment Battery Compartment Latch Inspecting the Facepiece Pairing a Radio Terminating Use Inspecting the Facepiece 2 3 4 14 Mask Communication Unit (MCU)
5 6 1 2 3 See also: Maintenance Carefully read all provided safety instructions before inspecting the equipment. Inspect the equipment before first use, before donning, after each use, and during periodic inspections. Refer to the figures in About This Equipment to identify equipment components. To inspect the facepiece 1) Inspect the facepiece for deformation, wear, cracks, or other damage. For more information, see the operating and maintenance instructions provided with your facepiece.
2) Inspect the communications module for damage such as cracks, chips, discoloration, corrosion, missing or loose parts, or burned or melted components. If there is a damage, remove the unit from service and tag it for repair by authorized personnel. Inspect the nosecup. Make sure the microphone port in the nose cup is clean and unobstructed. Power on the facepiece electronics by pressing and holding the power button. – The power button LED is solid green.
2) To complete the pairing process, refer to instructions provided by the manufacturer of your LMR or to reference information provided by 3M for compatible radios. Quick reference guides for pairing the facepiece RDI with specific LMRs are available from 3M. When the facepiece RDI and LMR are connected, the power button LED and RDI LED are solid blue, and the IVR system (available only with BCH) states, "Radio paired. Radio connected.
Do not alter or repair the electronic components of the facepiece beyond the scope of these instructions. Use only 3M Scott approved parts. i IMPORTANT NOTE The rubber tube on the MCU microphone is not sold as a service part. If the MCU microphone tube is damaged, replace the MCU (P/N 201625-01). i IMPORTANT NOTE For instructions to clean or repair the facepiece, see the operating and maintenance instructions provided with the facepiece.
Battery Charger Components 1 Battery Charger 2 Mounting Bracket - Single 3 Mounting Bracket - Double 4 Mounting Bracket - Triple 5 Daisy Chain Kit 6 Power Supply, 18 W 7 Power Supply, Hardwired Cable 8 Power Supply, High 9 Detachable Cordset - North America You can power the charger using any of the following power supplies: • • Low-power supply: Output Rated 24VDC, 750mA; Input Rated 100-240VAC, 1.
50/60 Hz; supports up to 3 battery chargers in a daisy-chain configuration • Vehicle DC power bus: 12V or 24 V; ATC/ATO 5 A inline fuse i IMPORTANT NOTE See Installing the Battery Charger for information about the required cables and power supply for your charging configuration. i IMPORTANT NOTE When using DC power from a vehicle, ensure that the power source chosen will provide the necessary power for the time required to recharge a battery.
All off No battery detected Solid green Charge complete Flashing green (500 ms on, 500 ms off) Charging Flashing red quickly (250 ms on, 250 ms off) System Fault Flashing red slowly (750 ms on, 250 ms off) Battery Fault • • If the charger's LEDs indicate a System Fault or Battery Fault, try the troubleshooting tips listed in Troubleshooting the Battery Charger. If the faults do not resolve after troubleshooting, remove the unit from service and tag it for repair by authorized personnel.
9) Plug the power supply into a wall outlet. i IMPORTANT NOTE Ensure that you are using a 3M Scott approved battery and power supply (low-power only). See Conditions of Safe Use. Do not connect a second power supply to the charger.
Ensure that you are using a 3M Scott approved battery and power supply (high-power only). See Conditions of Safe Use. Do not connect a second power supply to the connected chargers. Mounting the Battery Charger Mount a single battery charger or up to 3 chargers in a daisy-chain configuration on a flat horizontal or vertical surface (such as a desk or well) or in a vehicle.
• • • • • i Mounting template (for 1, 2, or 3 chargers) 4-40 x 3/4 in Phillips pan screws to secure the charger to the mounting bracket (2 per charger) Screw plugs (2 per charger) External charging cord (positive terminal to be fused with ATC/ATO 5 A inline fuse) (Not provided) Drill, drill bit (9/64"), and mounting screws/anchors (No. 6 flat head screws) - You will need 2 mounting screws/anchors for 1 charger, 4 for 2 chargers, and 6 for 3 chargers.
9) (Optional) Use cable ties or zip-ties to attach the power supply and its cord to the mounting bracket. For a vertical mount, attach the power supply to the bottom of the mounting bracket. For a horizontal mount, attach the power supply to the back of the mounting bracket. Troubleshooting the Battery Charger If your battery charger's LEDs indicate a system fault or battery fault, try these troubleshooting tips.
i IMPORTANT NOTE For instructions to clean the facepiece, see the operating and maintenance instructions provided with the facepiece. To repair the battery charger Repairs are limited to replacing the listed parts. i IMPORTANT NOTE Do not alter or repair this assembly, its components, or its accessories beyond the scope of these instructions. Use only 3M Scott approved parts.
LIMITED WARRANTY 3M Scott Fire & Safety (3M SCOTT) warrants Vision C5 Facepiece products (THE PRODUCTS) to be free from defects in workmanship and materials for as long as THE PRODUCTS are owned by the original end-user purchaser.
PRODUCTS including all accessories and optional equipment purchased and supplied at the time of original sale of THE PRODUCTS, except voice communication devices, in-mask displays, facepiece-integrated thermal imaging devices, rechargeable batteries, battery chargers, consumable supplies, and storage bags.
3M Personal Safety Division SCBA & Fire Solutions 4320 Goldmine Road, Monroe NC 28110 Telephone: (704) 291-8300 Technical Support: (800) 247-7257, ScottTechSupport@mmm.com Web: www.3MScott.com © 3M 2019. 3M and Scott are trademarks of 3M.
