User Guide

reater than many substrates
ABS
Aluminum
1, 2
EPDM rubber
Fabric/felt/cork
FRP– epoxy
FRP– polyester
Glass/ceramic
Leather
Neoprene rubber
3
Nitrile rubber
3
Nylon
Painted metal
1
Polyacrylic
Polycarbonate
4
Polyolefins
5
Polystyrene
Polystyrene (Beadboard)
PVC
Steel
1, 2
SBR
Wood/hardboard
TE-030
TE-015
Substrate TE-031
TE-040 TE-100 TS-115 HGS
Excellent
Good
Fair
Poor
TE-200 TS-230
3M
™
Jet-Weld
™
Adhesive Information
3M
™
Jet-Weld
™
Adhesive Selection Guide
Application
Temperature
Product Viscosity Color Open
Time
Set
Time
Shore
D
Tensile
Strength
Elong. Modulus
1 Not recommended for bonding
metal, glass and ceramic to
itself or each other due to low
moisture transmission of
substrates.
2Abrade uncoated aluminum.
Not for use on uncoated
aluminum subjected to
hot/humid conditions.
3Rubbers vary in composition.
Adhesion to specific rubber
must be evaluated by user.
4Adhesive may partially
delaminate from polycarbonate
at elevated temperatures.
5Polypropylene, polyethylene.
Corona or plasma treatment
may improve adhesion.
Note: User is responsible for
determining whether the 3M
product is fit for a particular
purpose and suitable for user’s
method of application.
Description
Extrudable. Fast set time. Best
for bonding woodand selected
plastics.
Extrudable. Very fast set time
for bonding wood and selected
plastics.
Extrudable. Fast setfor bonding
wide variety of plastics, including
polystyrene and polyacrylic.
Extrudable. Fast set time, low
viscosity, and strong, flexible bonds
for a wide variety of plastics, wood,
aluminum and glass.
Extrudable. Medium set time and
low viscosity for bonding wood and
selected plastics. Thin glue lines.
Low viscosity. Long open time.
Thin glue lines. Very high strength
to wood.Bonds selected plastics.
Sprayable/extrudable.Long set
time for wide variety of plastics,
including polystyrene and polyacrylic.
Bonds aluminum and glass to
plastic and wood.
TE-015
TE-030
TE-031
TE-040
TE-100
TE-200
TS-230
TS-115
HGS
250°F
(121°C)
250°F
(121°C)
250°F
(121°C)
250°F
(121°C)
250°F
(121°C
)
250°F
(121°C)
250°F
(121°C)
250°F
(121°C)
7,000
cps
16,000
cps
13,000
cps
7000
cps
7000
cps
3000
cps
9000
cps
16,000
cps
Bonds substrates such as wood,
FRPand many other plastics to
themselves, metal, and glass.
Very high green strength.
White/
off white
White/
off white
White/
off white
White/
off white
White/
off white
White/
off white
White/
off white
White/
off white
1.5
min.
1
min.
2
min.
2
min.
2
min.
4
min.
4
min
.
10
min.
15
sec.
30
sec.
30
sec.
40
sec.
1
min
.
2
min
.
2.5
min.
1
min.
65
60
50
35
61
60
45
47
3950
psi
3800
psi
3900
psi
2750
psi
4200
psi
4000
psi
3300
psi
3200
psi
750%
725%
725%
8 60%
675%
625%
700%
600%
2500
psi
11,200
psi
5600
psi
2850
psi
12,200
psi
9700
psi
5400
psi
3300
psi
Note: This technical information and data should be considered representative or typical only and should not be used for specification purposes.