Instructions and Parts List 3M-Matic 800rf ™ Important Safety Information BEFORE INSTALLING OR OPERATING THIS EQUIPMENT Read, understand, and follow all safety and operating instructions. Type 40800 Random Case Sealer with Spare Parts ™ AccuGlide 3 Taping Heads Serial No. For reference, record machine serial number here. 3M Industrial Adhesives and Tapes 3M Center, Building 220-5E-06 St.
This instruction manual covers safety aspects, handling and transport, storage, unpacking, preparation, installation, operation, adjustments, maintenance, troubleshooting, repair work and servicing plus parts list of the 3M-Matic 800rf Random case sealer. 3M Industrial Adhesives and Tapes 3M Center, Building 220-5E-06 St. Paul, MN 55144-1000 Edition March 2012 Copyright 3M 2012 All rights reserved The manufacturer reserves the right to change the product at any time without notice.
Replacement Parts and Service Information To Our Customers: This is the 3M-Matic™/AccuGlide™/Scotch® equipment you ordered. It has been set up and tested in the factory with Scotch® tapes. If technical assistance or replacement parts are needed, call or fax the appropriate number listed below. Included with each machine is an Instructions and Parts List manual. Technical Assistance / Replacement Parts and Additional Manuals: Contact your local service provider.
THIS PAGE IS BLANK
Replacement Parts And Service Information To Our Customers: This is the 3M-Matic™/AccuGlide™/Scotch® equipment you ordered. It has been set up and tested in the factory with Scotch® tapes. If any problems occur when operating this equipment and you desire a service call or phone consultation, call, write, or fax the appropriate number listed below. Included with each machine is an Instructions and Parts List manual.
THIS PAGE IS BLANK
TABLE OF CONTENTS - MANUAL 1: 800rf Random Case Sealer (For Taping Head Information - See MANUAL 2: AccuGlide 3 Taping Heads - 2 Inch) 800rf Random Case Sealer Page Cover Page Replacement Parts and Service Information ........................................................................ i - ii Table of Contents ................................................................................................................. iii - v Acronyms and Abbreviations .............................................
THIS PAGE IS BLANK 8
TABLE OF CONTENTS (continued) 5. Shipment, Handling, and Storage 5.1 5.2 5.3 5.4 Packed Machine Shipment and Handling .......................................................................... 15 Overseas Shipment Packaging (Optional) ......................................................................... 15 Handling and Transportation of Uncrated Machine ............................................................ 15 Machine Storage .......................................................................
THIS PAGE IS BLANK
TABLE OF CONTENTS (continued) 12. Troubleshooting 12.1 Troubleshooting .............................................................................................................. 39 - 40 13. Maintenance 13.1 13.2 13.3 13.4 13.5 13.6 13.7 13.8 13.9 13.10 13.11 13.12 13.13 13.14 Safety Measures (see section 3) .................................................................................... 41 Tools and Spare Parts Supplied with Machine ................................................................
ABBREVIATIONS AND ACRONYMS LIST OF ABBREVIATIONS, ACRONYMS 3M-Matic - Trademark of 3M St. Paul, MN 55144- 1000 AccuGlide - Trademark of 3M St. Paul, MN 55144-1000 Scotch - Trademark of 3M St. Paul, MN 55144-1000 Drw. - drawing Ex. - for example Fig. - exploded view figure no. (spare parts) Figure - Illustration Max. - maximum Min. - minimum Nr.
1-INTRODUCTION 1.1 Manufacturing Specifications / Description / Intended Use The 3M-Matic™ Model 800rf Type 40800 Automatic Random Case Sealer with AccuGlide™ 3 Taping Heads is designed to accept filled, regular slotted containers from an existing conveyor, fold the top flaps, and apply a “C” clip of Scotch™ brand Pressure-Sensitive Film Box Sealing Tape to the top and bottom center seams. Two sidedrive belt assemblies convey the cases through the machine.
1-INTRODUCTION (continued) 1.2.1 Importance of the Manual 1.1 Manufacturing Specifications / Description / Intended Use (continued) The manual is an important part of the machine; all information contained herein is intended to enable the equipment to be maintained in perfect condition and operated safely. Ensure that the manual is available to all operators of this equipment and is kept up to date with all subsequent amendments.
2-GENERAL INFORMATION 2.1 Data Identifying Manufacturer and Machine For Commercial Use Only 2.
2-GENERAL INFORMATION (continued) 2.3 Warranty Equipment Warranty and Limited Remedy: THE FOLLOWING WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND ANY IMPLIED WARRANTY ARISING OUT OF A COURSE OF DEALING, A CUSTOM OR USAGE OF TRADE: 3M sells its 3M-Matic™ 800rf Adjustable Case Sealer, Type 40800 with the following warranties: 1.
3-SAFETY 3.1 General Safety Information 3.2 Explanation of Signal Word and Possible Consequences Read all the instructions carefully before starting work with the machine; please pay particular attention to sections marked by the symbol: This safety alert symbol identifies important messages in this manual. READ AND UNDERSTAND THEM BEFORE INSTALLING OR OPERATING THIS EQUIPMENT.
3-SAFETY (continued) 3.3 Table of Warnings WARNING • To reduce the risk associated with mechanical and electrical hazards: − Read, understand, and follow all safety and operating instructions before operating or servicing the case sealer. − Allow only properly trained and qualified personnel to operate and service this equipment. Figure 3-2 WARNING • To reduce the risk associated with hazardous voltage: − Position electrical cord away from foot and vehicle traffic.
3-SAFETY (continued) WARNING • To reduce the risk associated with sharp blade hazards: − Keep hands and fingers away from tape cutoff blades under orange blade guards. The blades are extremely sharp. WARNING Sharp Blade Important! Tape cutting blade. Never remove the safety device which covers the blade on the top and bottom taping units. Blades are extremely sharp. Any error may cause serious injuries (Figure 3-5).
3-SAFETY (continued) 3.4 Operator's Qualifications - WARNING Machine Operator Mechanical Maintenance Technician Electrical Maintenance Technician Manufacturer’s Technician/Specialist (See Section 3.11) 3.5 Number of Operators The operations described below have been analyzed by the manufacturer; the recommended number of operators for each operation provides the best and safest work performance.
3-SAFETY (continued) Skill 2a: Electrical Maintenance Technician This operator is trained to use the machine as the MACHINE OPERATOR and in addition is able to: • Work with the safety protection disconnected • Check and adjust mechanical parts • Carry out machine maintenance operations / repairs / adjustments / repair electrical components He is allowed to work on live electrical panels, connector blocks, control equipment, etc. 3.
3-SAFETY (continued) 3.12 Component Locations Refer to Figure 3-9 below to acquaint yourself with the various components and controls of the case sealer. Also refer to Manual 2 for taping head components.
Important Safeguards (continued) 78-8070-1333-5 78-8070-1336-8 on Tape Head 78-8113-6882-4 78-8113-8912-9 78-8113-6883-2 78-8070-1317-8 78-8070-1366-5 78-8070-1331-9 78-8137-0886-0 78-8137-0221-0 78-8113-6750-3 78-8062-4266-1 78-8137-1331-6 78-8095-1141-9 78-8070-1339-2 3M Logo (not shown) 78-8070-1329-3 78-8060-8481-6 Leg Height Adjustment Label (not shown) Figure 1-1 – Replacement Labels/3M Part Numbers 800rf-NA 11 2012 March
4-SPECIFICATIONS 4.1 Power Requirements Electrical: 115 Volt, 60Hz, 3.8 A (440 watts) (*Note: Electric Information may not relect machine electrical settings/requirements in your area) The machine is equipped with a 2.4m [8 foot] standard neoprene covered power cord and a grounded plug. Contact your 3M Representative for power requirements not listed above. Pneumatic – 6 bar gauge pressure [87 PSIG] @ 21 C, 1.01 bar [3.
4-SPECIFICATIONS (continued) 4.6 Tape Roll Diameter Up to 410mm [16 inch] maximum on a 76.2mm [3 inch] diameter core. (Accommodates all system roll lengths of Scotch® film tapes.) 4.7 Tape Application Leg Length – Standard 70mm ± 6mm [2 3/4 inch ±1/4 inch] Tape Application Leg Length – Optional 50mm ± 6mm [2 inch ±. 1/4 inch] (See "Removing Taping Heads Procedure – Changing the Tape Leg Length") 4.8 Box Board Style – regular slotted containers – RSC 125 to 275 P.S.I.
4-SPECIFICATIONS (continued) 4.10 Machine Dimensions Min. 1830mm Max. 2050mm 3308mm 1520mm 1094mm 1121mm 920mm 892mm 694mm 4.11 Machine Noise Level: Acoustic pressure measured at a distance of 1m. from machine with Scotch PVC adhesive tape in operation; 78dB Acoustic radiation pressure at 1.6m. height with Scotch PVC adhesive tape in operation; 73dB Measurement taken with appropriate instrument: (Type SPYRI-MICROPHON 11). 4.12 Set-Up Recommendations: • • • Machine must be level.
5-SHIPMENT-HANDLING-STORAGE, TRANSPORT 5.1 Shipment and Handling of Packed Machine L The machine and the infeed conveyor are shipped in 2 separate packings, fixed on a wooden pallet. They can be uplift with a normal forklift. The standard packing is suitable for surface and air transportation. Oversea packing on request. W H Packing dimensions 800rf l = length: 2880mm: w = width: 1480mm h = height: 2050mm Weight: 617kg Packaging Overall Dimensions (Figure 5-1) Figure 5-1 5.
6-UNPACKING 6.1 Uncrating Removal of Pallet The envelope attached to the shipping box contains the uncrating instructions of the machine (Figure 6-1). Loosen and remove nuts and brackets using the open end spanner supplied in the tool box (Figure 6-4). Figure 6-1 Figure 6-4 A cardboard box is located under the machine body. Retrieve the instruction manual for additional procedures of the set up. The box also contains parts removed for shipping, spare parts and tools. Cut straps.
7-INSTALLATION 7.1 Operating Conditions The machine should operate in a dry and relatively clean environment (See Specifications). WARNING • To reduce the risk associated with muscle strain: − Use the appropriate rigging and material handling equipment when lifting or repositioning this equipment. − Use proper body mechanics when removing or installing taping heads that are moderately heavy or may be considered awkward to lift. 7.
7-INSTALLATION (continued) 7.5 Safety Guards: Inside and Outside Machine Emergency Stop Push-Button B Position and assemble the inside (A) and outside (B) guard panels with the upper and bottom brackets and stiffening profile plates as shown in the pictures (Figure 7-4). Figure 7-4 A Inside Safety Guards Support brackets (upper and bottom); 4+4 socket head screws each bracket (Figure 7-5). Figure 7-5 Stiffening profile plate (upper): 2+2 socket head screws (Figure 7-6).
7-INSTALLATION (continued) (infeed conveyor attachment continued) Approach the infeed conveyor to the machine and fix it using the screws previously removed (Figure 7-11). Figure 7-11 B10, B1, B2 infeed conveyor photocells connections (Figure 7-12).
7-INSTALLATION AND SET-UP (continued) 7.6 Pneumatic & Control Board Connections (continued) - Connect an air tube to the ON/OFF valve and attach it with a strap. Minimum inside diameter of the tube 10mm; air pressure 6 BAR. - Give air to the machine with the ON/OFF valve (Figure 7-15). Figure 7-15 Position the control board near the machine. Feeder cables: Connect the cable with multipolar connectors from the machine and from conveyor to the control board (Figure 7-16).
7-INSTALLATION AND SET-UP (continued) (Pneumatic & Control Board Connections - continued) Figure 7-19 Front junction box connector (Figure 7-20). Figure 7-20 Rear junction box connector. (Figure 7-21).
7-INSTALLATION AND SET-UP (continued) 7.7 Preliminary Electric Check-Out Before connecting the machine to the mains please carry out the following operations: - Make sure that the socket is provided with a ground protection circuit and that both the mains voltage and frequency meet the indications on the name plate of the machine. - Check that the connection of the machine to the mains meets the provisions of law and/or the safety regulations in your country.
7-INSTALLATION AND SET-UP (continued) 7.9 Completion of Taping Heads One Way Tension Roller See Manual 2 for Complete Instructions: 1. Place the Upper Taping Head in a convenient working position .2. Use Figure 7-22 and tape threading label. Position the tape supply roll so the adhesive side of tape is facing the front of the taping head as it is pulled from the supply roll. 3. Attach the threading needle to the end of the roll.
8-CONTROLS 8.1 Controls Board 1. 2. Main switch (Figure 8-1). Emergency stop push button (lockable) 3. Auxiliaries push button (control board electrical components habilitation) 4. Reset push button (new work cycle predisposition ) 5. Start push button 6. Stop push button 7. Voltage warning light 8. Thermal switch warning light 9. Warning (flashing light + buzzer on top guardnot shown) 10. Operating mode panel (Figure 8-2).
9-OPERATION 9.1 Operation - Give air to the machine by the ON/OFF valve, set the main switch to ON (I) position; - Close the safety guards; release the E-stops; - Press AUXILIARIES button, - Press RESET button; press START button. The box, after passed the infeed conveyor belt, obscures the first photocell (Figure 9-1) Figure 9-1 A When the second photocell is obscured the infeed conveyor belt goes down in order to stop the next box. The side guides A align the box.
9-OPERATION (continued) Simultaneously the rear flap is folded the fork goes down and the side belts restart to run (Figure 9-6). Figure 9-6 C The side flaps are folded (Figure 9-7). Figure 9-7 The two taping heads seal the box with adhesive tape (Figure 9-8). Figure 9-8 When the box has passed the fifth photocell, the upper group goes up, the side drive belts open and the infeed conveyor belt (on which awaits the next box) comes up and restarts (Figure 9-9).
9-OPERATION (continued) Important! If, for any reason, the box should stop inside the machine, the machine will stop operating after 10 seconds. To remove the box and restart, operate as follows: - 6 press the E-stop, open the safety guard, remove the box, close the safety guard an release the E-stops, press the AUXILIARIES push-button; press the RESET push-button, press the START (I) button to start the cycle 9.
9-OPERATION (continued) 9.4 Alarms Warning light a: Thermal switch activation (motor overload) - The machine cannot be started; machine stops if it is running To restart press 3, after 4, then 5 push-buttons. Warning light b: Time out cycle (the machine will stop when the cycle taping boxes is not done just in time as preselected; 10 seconds approximately). - machine stop. to restart press 4, 5 push-buttons; if necessary, open a safety guard to eliminate a jam, press 3, 4, 5 push-buttons.
10-SAFETY DEVICES OF THE MACHINE 10.1 Blade and Safety Guards 3308mm 1830mm 2050mm Both the top and bottom taping units have a blade guard (See Manual 2: AccuGlide™ 3 Taping Heads - 2 Inch). WARNING • To reduce the risk associated with sharp blade hazards: − Keep hands and fingers away from tape cutoff blades under orange blade guards. The blades are extremely sharp.
11 - SET UP AND ADJUSTMENTS 11.1 Tape Loading on the Top Unit Figure 11-1 Insert a tape roll on the drum and push it fully forward. Attach the tape leg to the threading tool (supplied with the tools kit) Figure 11-1. Figure 11-2 Insert the plastic threading leader through the taping unit. Take care to keep hands away from the tape cutting blades (Figure 11-2 and 11-3).
11 - SET UP AND ADJUSTMENTS (continued) 11.2 Tape Loading on the Bottom Unit Remove the bottom taping unit from its housing and put it on a working bench (Figure 11-7). - Put a tape roll on the drum and thread the tape through the unit as shown on the label in the same manner as for the top unit (Figure 11-8). - Put the bottom unit back into its housing. 11.3 Tape Drum Alignment Figure 11-7 Check the centering of the tape on the rollers of the taping unit.
11 - SET UP AND ADJUSTMENTS (continued) Figure 11-11 11.6 Main Pressure Regulator A A) it adjusts the entry working pressure B) gauge to read the entry air pressure Optimal working pressure: 6 BAR Feeding tube diameter: 10mm Note: in case the working pressure is below 6 BAR or the feeding tube has a small diameter, some malfunctions can happen! (ex: the upper group comes down, the rear flap folder works but the machine stops) B 11.
11 - SET UP AND ADJUSTMENTS (continued) 11.9 Box Height Pick-up 3) Pressure regulator with built-in pressure gauge. The pressure regulator 3 adjusts the pressure according to the board strength. - Decrease in case of light boxes. Increase in case of strong boxes. Minimum pressure must be adjusted so that the paddle returns automatically in position once the box is passed. Figure 11-16 Working pressure: 0,5÷1,0 bar (entry pressure: 6 bar). 2 11.
11 - SET UP AND ADJUSTMENTS (continued) 11.11 Pneumatic Speed Regulators A) Upper unit ascent-descent speed regulators B) Centering guides (infeed conveyor) speed regulators C) Side belts opening-closing speed regulators Side belts opening-closing speed regulators. These are not common operations. They have to be made only when it has been necessary to work on the pneumatic cylinder.
11 - SET UP AND ADJUSTMENTS (continued) 11.12 Speed Regulators of the Rear Flap Folder 2 These are not common operations. They have to be made only when it has been necessary to work on the pneumatic cylinder. 1 To change the speed, do as follows: The speed of the rear flap folder unit can be adjusted by the flow regulators mounted on the pneumatic cylinders.
11 - SET UP AND ADJUSTMENTS (continued) B 11.14 Adjustment of the Sensor that Stops the Descent of the Upper Unit A 3 2 The descent of the upper group is stopped when the sensor 1 is activated (yellow led up). The sensor is mounted on the cylinder 2 by the support 3. 1 To change the intervention time of the sensor do as follows: 1) Loosen, the screw 4 of the support; 2) Move the support with the sensor along the cylinder; 4 Figure 11-27 Towards A Before Figure 11-28 Towards A to delay the braking.
11 - SET UP AND ADJUSTMENTS (continued) 11.15 Adjustments of the Side Compression Rollers - - + To increase or decrease the pressure of the side rollers on the box, do as follows: - + loosen the nuts; change the position of the rollers; lock the nuts. Figure 11-32 - increase the pressure when the upper flaps are not well closed after the sealing. Before After Figure 11-33 - decrease the pressure when the upper flaps are one upon the other. Before After Figure 11-34 1 11.
11 - SET UP AND ADJUSTMENTS (continued) 6 5 4 3 S 2 1 D Figure 11-36 11.17 Use and Adjustments of the Photocells Photocell 1 The photocell does not operate at the first machine starting ; when it is obscured by the next box the motorized plane of the infeed conveyor stops. No adjustment is necessary. Photocell 2 When is obscured by the box the motorized plane goes down and the side guides center the box. No adjustment is necessary.
12-TROUBLE-SHOOTING The Troubleshooting Guide lists some possible machine problems, causes and corrections. Also see Manual 2 "Troubleshooting" for taping head problems. 12.1 Troubleshooting Guide Problem Cause Correction Tape is not centered on the box. The side belts are not correctly positioned. Check the position. The box flaps are not centered. Check the flaps dimensions; the flaps must be equals. Tape is not positioned in the center of the taping head. Adjust the tape position.
12-TROUBLE-SHOOTING (continued) Troubleshooting Guide Problem Cause Correction The box is not dragged under the head. The box is too full load; box side flaps are opened. Check. Driving pulley rings on motorizing side units are worn out. Motorizing side units low pressure. The head is not correctly positioned; it is too down. Defective head power valve 800rf-NA 40 Replace as necessary.
13-MAINTENANCE AND REPAIRS 13.1 Safety Measures (see section 3) 13.2 Tools and Spare Parts Supplied with the Machine Carrying out maintenance and repairs may imply the necessity to work in dangerous situations. See Spare Parts Order Section. 13.
13-MAINTENANCE AND REPAIRS (continued) 13.8 Securities Check-up 1 1) Tape units blade guards; 2) Lockable emergency stop push-buttons; 3) Rigid protection plate mounted on the side drives; 4) Safety guards; 1 1 1 13.
Maintenance (continued) WARNING Off • To reduce the risk associated with mechanical and electrical hazards: − Turn electrical and air supply off and disconnect before performing any adjustments, maintenance or servicing the machine or taping heads • To reduce the risk associated with impact hazards: Figure 13-4 − Always use appropriate supporting means when working under the upper drive assembly 13.11 Side Drive Belts Replacement Operator - Skill Level 2.
13-MAINTENANCE AND REPAIRS (continued) Remove the locking screws and the protection covers. Figure 13-9 Loosen the tensioning screws. Figure 13-10 Release the nut of the tensioning plate. Figure 13-11 Remove and replace the drive belt. Important Before setting the new belt, check the wear of the orange plastic rings on the drive pulleys: replace them if they are worn out.
Adjustments (continued) 13.12 Box Drive Belt Tension The two (2) continuously moving drive belts convey boxes through the tape applying mechanism. The box drive belts are powered by an electric gear motor. Tension adjustment of these belts may be required during normal operation. Belt tension must be adequate to positively move the box through the machine and the belts should run fully on the surface of the pulleys at each end of the frame.
THIS PAGE IS BLANK 46
13-MAINTENANCE AND REPAIRS (continued) 13.
THIS PAGE IS BLANK 48
14-ADDITIONAL INSTRUCTIONS 15-ENCLOSURES / SPECIAL INFO. 14.1 Information for Disposal of Machine 15.1 Statement of Conformity The machine is composed of the following materials: - See Section 1. Steel structure Nylon rollers Drive belts in PVC Nylon pulleys 15.2 Emission of Hazardous Substances Nothing to report For machine disposal, follow the regulations published in each country. 15.3 List of Safety Features 14.
THIS PAGE IS BLANK 50
16-Electrical Technical Diagram WARNING • − 800rf-NA To reduce the risk associated with mechanical and electrical hazards: Turn electrical and air supply off and disconnect before performing any adjustments, maintenance or servicing the machine or taping heads 51 2012 March
16-TECHNICAL DIAGRAMS 16.
16-TECHNICAL DIAGRAMS (continued) 16.
Block Pressers Column Cylinder Centering Cylinder Motor Cylinder Gate Cylinder Gate Cylinder Close Cylinder 1 Close Cylinder 2 Stop Box Cylinder 16-Pneumatic Technical Diagram 800rf-NA 54 2012 March
16-TECHNICAL DOCUMENTATION AND INFORMATION (continued) 16.3 Spare Parts Order The following parts are normal wear items and should be ordered and kept on hand as used. Qty. 4 Part Number Description 78-8054-8841-4 Belt – Drive W/Pin Also see Manual 2 for recommended taping head spare parts. Label Kit In the event that any labels are damaged or destroyed, they must be replaced to ensure operator safety. A label kit, part number 78-8098-9177-9 is available as a stock item.
THIS PAGE IS BLANK 56
800rf Random Case Sealer, Type 40800 Frame Assemblies To Order Parts: 1. Refer to first illustration, Frame Assemblies, for the Figure Number that identifies a specific portion of the machine. 2. Refer to the appropriate Figure or Figures to determine the parts required and the parts reference number. 3. The Parts List that follows each illustration, includes the Reference Number, Part Number and Part Description for the parts on that illustration.
THIS PAGE IS BLANK 58
800rf Random Case Sealer Figure 15077 Figure 15076 Figure 10440 Figure 15071 Figure 15072 15082 All Pneumatic Components and Plumbing Figure 15294 Figure 15075 Figure 15295 Figure 15078 Figure 15079 Figure 15096 Figure 15073 See End of Manual for Infeed Conveyor Illustrations and Parts Lists.
800rf 12 10 14 8 11 5 11 18 9 13 18 6 10 19 19 7 1 7 16 3 15 2 13 16 4 17 17 Figure 15071 800rf-NA 60 2012 0DUFK
800rf Figure 15071 Ref. No. 3M Part No.
800rf Figure 10440 800rf-NA 62 2012 0DUFK
800rf Figure 10440 Figure 10440 Ref. No. 3M Part No.
800rf 13 13 12 12 11 11 66 7 7 10 1 88 99 44 2 5 3 Figure 15072 800rf-NA 64 2012 0DUFK
800rf Figure 15072 Ref. No. 3M Part No. Description 15072-1 78-8137-3607-7 Frame - Upper Head- R/H 15072-2 78-8137-3608-5 Frame - Upper Head- L/H 15072-3 78-8137-3609-3 Screw - M8 X 20 15072-4 78-8017-9318-9 Washer-Plain-Metric M8 15072-5 78-8017-9313-0 Nut Self Locking M8 Nick. Pl. 15072-6 78-8137-3601-1 Holder - Upper Head- R/H 15072-7 78-8137-3611-9 Holder - Upper Head- L/H 15072-8 26-1003-5820-4 Screw - Hex Hd..
800rf 11 44 2 2 55 3 3 4 4 55 66 7 9 10 10 14 14 15 15 13 13 9 10 10 8 8 12 12 11 11 Figure 15073 800rf-NA 66 2012 0DUFK
800rf Figure 15073 Ref. No. 3M Part No. Description 15073-1 78-8137-3613-5 Frame - Bottom Head- R/H 15073-2 78-8137-3614-3 Frame - Bottom Head- L/H 15073-3 78-8054-8862-0 Spacer - 12 X 12 X 1 - M40 15073-4 78-8010-7169-3 Washer - Flat M6 15073-5 26-1000-0010-3 Screw - Metric, M6 X 12, Hex Hd.. 15073-6 26-1003-7963-0 Screw - Soc. Hd. M8 X 16 15073-7 78-8017-9318-9 Washer - Plain - Metric M8 15073-8 78-8137-3615-0 Cylinder Support 15073-9 26-1003-7964-8 Screw Soc. Hd. Hex Soc.
0rf 14 15 41 13 16 8 38 15 37 37 30 18 17 17 12 31 32 34 36 36 33 33 99 40 39 35 35 28 28 29 29 1 23 23 27 3 11 11 26 26 10 44 66 Figure 15074 800rf-NA 20 20 21 25 25 22 19 19 24 22 55 77 68 2012 0DUFK
800rf Figure 15074 Ref. No. 3M Part No.
800rf 44 2 3 25 33 66 77 26 14 14 12 15 15 13 8 11 24 11 11 11 19 19 44 9 10 23 23 22 22 17 4 16 16 21 5 18 20 20 Figure 15075 800rf-NA 70 2012 0DUFK
800rf Figure 15075 Ref. No. 3M Part No. Description 15075-1 78-8137-3634-1 Bottom Plate For Side Roller R/H 78-8137-3635-8 Bottom Plate For Side Roller L/H 15075-2 78-8137-3636-6 Top Plate For Side Roller 15075-3 78-8137-3637-4 Block For Union Plates 15075-4 26-1001-9843-6 Screw Flat Soc. Hd.M6 X 16 15075-5 26-1005-5316-8 Screw, Flat Hd. Hex Dr. M5 X 16 15075-6 78-8010-7417-6 Nut - Metric, Hex Stl. M5 15075-7 78-8005-5741-1 Washer - Flat, M5.
800rf 31 6 3 32 33 1 55 4 29 29 36 36 35 35 26 26 14 14 17 17 28 27 8 10 10 18 16 16 15 15 11 9 77 24 25 25 23 34 30 22 38 13 13 18 18 37 23 20 22 22 800rf-NA 12 21 18 18 17 17 Figure 15076 72 2012 0DUFK
800rf Figure 15076 Ref. No. 3M Part No.
800rf 29 58 58 11 28 28 54 54 25 25 28 28 56 57 57 55 55 60 60 61 61 53 53 52 52 51 51 59 27 27 26 26 10 10 13 13 44 44 3 18 19 18 19 45 45 4 3 14 14 19 18 1918 46 46 13 13 46 46 47 48 48 50 36 36 41 37 37 33 41 42 34 42 34 35 35 40 40 32 16 16 23 43 43 16 16 24 2 20 20 31 31 17 22 22 55 99 22 22 55 11 11 10 10 12 31 31 50 50 49 49 48 21 20 20 15 15 27 27 43 23 38 38 39 39 30 30 66 7 9 8 Figure 15077 800rf-NA 74 2012 0DUFK
Figure 15077 Ref. No. 3M Part No.
800rf 22 20 4 1 1 17 17 2 22 21 33 6 19 19 9 5 14 14 18 19 19 7 13 13 12 12 9 11 16 15 10 88 Figure 15078 800rf-NA 76 2012 0DUFK
800rf Figure 15078 Ref. No. 3M Part No. Description 15078-1 78-8137-3672-1 Fixing Bracket, Box 15078-2 26-1004-5507-5 Washer M8 15078-3 26-1003-5842-8 Screw Hex Hd.. M8 X 20 15078-4 78-8137-3673-9 Fixing Spacer, Box 15078-5 78-8091-0656-6 Screw - Hex. Soc. Hd.
800rf Random Case Sealer 35 35 32 32 36 36 44 42 42 43 43 45 45 39 39 40 40 41 41 21 21 19 37 37 33 33 17 34 34 17 38 38 47 47 48 48 27 27 46 46 49 49 11 12 12 9 9 23 22 22 14 14 50 50 31 31 11 26 26 28 28 16 16 19 19 24 24 13 13 30 30 29 29 10 10 20 20 18 18 19 19 15 15 22 33 19 19 22 33 Optional OPTIONAL 4 4 7 7 57 57 5 5 8 8 66 54 54 53 53 52 52 55 55 56 56 51 51 6 6 Figure 15079 / 1 800rf-NA 78 2012 0DUFK 25 25
800rf Figure 15079 / 1 Ref. No. 3M Part No.
800rf Random Case Sealer 55 66 2 7 44 3 30 30 88 99 27 27 25 26 26 18 1 12 12 12 29 29 28 28 13 31 31 32 11 11 10 10 28 28 13 13 22 22 23 24 24 21 21 22 22 14 14 19 19 14 14 15 15 20 20 21 21 17 17 15 15 16 18 Figure 15079 / 2 800rf-NA 80 2012 0DUFK
800rf Figure 15079 / 2 Ref. No. 3M Part No. Description 15079-1 78-8137-3703-4 Support - Plate Connectors 15079-2 26-1003-7957-2 Screw Soc. Hd. Hex Hd.. M6 X 16 15079-3 26-1000-0010-3 Washer - Flat M6 15079-4 78-8137-3704-2 Carter Protection Connectors 15079-5 26-1003-5820-4 Screw - Hex Hd..M-5 X 12 15079-6 78-8005-5741-1 Washer - Flat, M5 15079-7 78-8137-3705-9 Basing Housing M12 15079-8 78-8032-0379-9 Screw - Soc. Hd. Hex Hd..
800rf Random Case Sealer 800rf 77 12 13 13 33 13 13 99 7 7 7 10 10 77 77 77 9 9 88 22 99 99 11 11 66 1 4 44 Figure 15082 / 1 800rf-NA 22 22 82 3 33 2012 0DUFK
800rf Figure 15082 / 1 Ref. No. 3M Part No. Description 15082-1 78-8137-3745-5 Pneumatic Unit 15082-2 78-8137-3746-3 Regulator - Air Pressure 0-6 ATM 15082-3 78-8137-3747-1 Regulator - Air Pressure 0-10 ATM 15082-4 78-8119-8618-7 Union - Multiple, 33041008 15082-5 78-8076-4664-7 Union - Female 15082-6 78-8137-3748-9 Multipolar Connector 15082-7 78-8137-3749-7 Speed Regulator Assy 15082-8 78-8137-3750-5 Regulator W/Gauge - Pressure 15082-9 78-8091-0315-9 Elbow - 3199.08.
18 18 18 18 800rf-NA 16 16 14 14 19 19 20 20 V1A 84 V3B 15 15 17 17 15 15 V4B V2A Cilindri colonne Blocco pressatori 55 20 20 16 16 14 14 19 19 18 18 18 18 2012 0DUFK 34 34 33 33 V1A V3B V2A V4B 22 22 V9B V10A V6A V7A V7B V9A 31 32 V6B 30 V8B 24 24 Cilindro chiudifalda 1 V10B V9B V9A V8A V5A V11B V11A V5B 25 V7A Cilindro spatola V7B V10B V6B 23 V10A V5A 28 V8A V6A 27 27 26 26 21 21 V5B V11A V11B Cilindro centratore 29 221 Cilindri fermascatol
800rf Figure 15082 / 2 Ref. No. 3M Part No.
800rf 18 18 24 24 35 38 38 37 39 40 40 36 14 14 41 41 41 44 44 42 26 26 45 46 43 45 45 25 25 23 23 55 55 27 57 57 59 55 55 62 62 58 58 60 60 56 62 62 61 63 63 64 64 29 29 22 47 47 48 48 47 47 50 50 49 50 50 52 51 28 28 53 53 54 Figure 15082 / 3 800rf-NA 86 2012 0DUFK
800rf Figure 15082 / 3 Ref. No. 3M Part No. Description 15082-46 78-8137-3765-3 Linear Unit DFM-40-B-P-A-KF 15082-47 78-8137-3766-1 Flow Regulator 15082-48 26-1017-3315-7 Swinging Flange 15082-49 78-8076-5170-4 Cylinder DNU-40-100-PPV-A-SN 15082-50 78-8091-0315-9 Elbow - 3199.08.
800rf 86 86 81 81 1 1 77 77 89 89 59 59 99 98 98 58 71 58-71 63 63 7 5 5 6 6 7 4 4 21 66 5 5 17 17 16 16 22 22 55 112 112 52 52 72 72 107 107 73 73 104 5 5 66 56 56 47 57 57 50 50 32 6 6 75 75 74 74 46 46 103 103 109 109 108 31 31 30 30 47 48 48 44 40 40 24 105 70 33-70 55 55 15 15 110 111 111 54 21 94 62 62 54 53 53 8 94 94 61 61 64 64 65 65 41 41 96 96 97 68 68 55 66 67 67 66 66 78 78 108 39 39 106 106 69 22-69 49 49 51 51 38 38 42 42 76 91 76-91 41 4
800rf Figure 15294 / 1 Ref. No. 3M Part No.
800rf Random Case Sealer 99 88 11 11 42 42 45 45 12 12 10 43 43 99 44 44 11 11 14 14 13 13 33 33 15 32 32 11 11 36 36 34 34 23 23 33 33 11 11 35 35 37 37 14 14 13 13 24 24 28 28 28 29 27 27 25 25 26 26 Figure 15294 / 2 800rf-NA 90 2012 0DUFK
800rf Figure 15294 / 2 Ref. No. 3M Part No.
800rf-NA 92 18 23* 23* 20 * = 20 Figure 15295 22* 21* 19 19 11 11 22* 22 21* 13 14 24 24 25 17 17 32 6 30 34 16 16 17 15 17 27 28 28 4 1 99 12 12 14 14 18 18 13 19 19 32 32 30 30 35 77 88 26 26 30 34 34 55 6 2012 0DUFK 44 45 45 39 39 40 40 12 12 41 42 43 42 38 38 13 14 10 37 26 26 31 31 30 2 30 33 33 29 31 31 30 30 800rf Random Case Sealer 800rf
800rf Figure 15295 Ref. No. 3M Part No.
800rf Random Case Sealer 800rf 17 9 24 18 19 8 21 23 22 5 20 6 4 3 16 15 7 14 13 13 1 2 10 Figure 15296 Figure 15096 // 1 1 11 12 800rf-NA 94 2012 0DUFK
800rf Figure 15296 / 1 Ref No 3M Part Number Description 15296-1 15296-2 15296-3 15296-4 15296-5 15296-6 15296-7 15296-8 15296-9 15296-10 15296-11 15296-12 15296-13 15296-14 15296-15 15296-16 15296-17 15296-18 15296-19 15296-20 15296-21 15296-22 15296-23 15296-24 15296-25 15296-26 15296-27 15296-28 15296-29 15296-30 15296-31 15296-32 15296-33 15296-34 15296-35 15296-36 15296-37 15296-38 15296-39 15296-40 78-8137-3737-2 78-8137-3738-0 78-8060-7814-9 78-8010-7418-4 26-1000-0010-3 78-8137-3739-8 78-8010-7
800rf 70-72 39-40 71 30 25-26-27 28-29 30-31-73 35-36 33-34 37-38 XT1 41-42 45-46 41-42 52-53-54-55 56-53-54-55 HL1 Voltage Indicator White HL2 Red Indicator Light Thermal 57-58-59-60 61-62-63 SB4+HL4 Ready White SB5 Stop Red 47-48 47-48 47-48 47-48 67 49-50-51 SB1 Emergency HL14 HL12 HL15 HL11 Break / End Low Emergency Low Pressure tape Closing Guide 58-60-62-64-65 SB6+HL16 Start Green HL10 Cycle Time to Max 58-62-66 55-58-68 SB7 Reset Blue SA4 Reset Blue HL13 Line Full 55-58-
800rf Figure 15296 / 2 Ref No 3M Part Number Description 15296-41 78-8137-6015-0 Relays G2R-2 24VDC 15296-42 78-8137-4085-5 Socket 15296-43 78-8137-6015-0 Relays G2R-2 24VDC 15296-44 78-8137-4085-5 Socket 15296-45 78-8137-6015-0 Relays G2R-2 24VDC 15296-46 78-8137-4085-5 Socket 15296-47 78-8137-6017-4 Contact 15296-48 78-8137-0778-9 Automatic Switch 15296-49 78-8137-0609-6 Emergency Button 15296-50 78-8137-0797-9 Latch & contact.
THIS PAGE IS BLANK 98
800rf Figure 15086 Figure 15085 Figure 15084 Figure 15083 Figure 15087 Figure 15085 Figure 15084 Infeed ConveyorFrame Assemblies 800rf-NA 99 2012 March
800rf 35 9 29 29 36 20 9 37 27 29 39 32 31 40 30 22 38 44 38 41 25 28 16 2 1 18 17 18 42 43 21 2 33 17 19 3 24 25 23 2 3 4 5 6 3 7 OPTIONAL 8 14 13 11 10 12 9 15 48 48 47 47 45 45 46 46 Figure 15083 800rf-NA 100 2012 March
800rf Figure 15083 Ref. No. 3M Part No.
800rf 34 12 1 3 33 9 7 9 6 13 8 5 20 3 19 15 16 1010 2 35 4 11 9 14 37 36 23 21 17 18 28 22 24 38 26 27 29 31 32 30 Figure 15084 800rf-NA 102 2012 March
800rf Figure 15084 Ref. No. 3M Part No. Description 15084-1 78-8137-6106-7 Shaft - Motor 15084-2 78- Frame - Right Side 15084-3 78-8137-6108-3 Roller Assembly 15084-4 78-8076-5309-8 Belt 15084-5 78-8137-6109-1 Powered Roller 15084-6 78-8137-6110-9 Roller 6 X 6 X 20 15084-7 78-8076-5302-3 Snap - Roller 15084-8 78-8057-5811-3 Key - 6 X 6 X 20mm 15084-9 78-8055-0668-6 Washer 15084-10 26-1005-5318-4 Screw M6 X 55 Zinc.
800rf 24 23 22 25 29 34 32 27 33 20 21 31 28 31 34 26 19 13 12 10 9 3 1 11 4 2 7 5 16 14 15 16 17 18 6 6 8 5 7 Motor - See Figure 15084 Figure 15085 800rf-NA 104 2012 March
800rf Figure 15085 Ref. No. 3M Part No.
800rf 24 25 10 16 23 6 12 13 11 9 7 19 14 8 6 39 40 3 26 31 13 32 33 34 2 1 3 2 15 22 18 21 20 12 5 27 2 17 4 16 7 41 41 28 2 26 38 29 30 37 35 37 36 Figure 15086 800rf-NA 106 2012 March
800rf Figure 15086 Ref. No. 3M Part No.
800rf 3 2 1 3 12 5 5 6 6 13 7 11 3 3 8 10 9 4 Figure 15087 800rf-NA 108 2012 March
800rf Figure 15087 Ref. No. 3M Part No. Description 15087-1 78-8137-3767-9 Cylinder DNC-40-170-PPV-A 15087-2 26-1017-3315-7 Swinging Flange 15087-3 78-8137-3768-7 Compact Cylinder ADNP-50-15 15087-4 78-8137-3769-5 Swinging Flange SNCB-50 15087-5 78-8091-0315-9 Elbow – 3199.08.
THIS PAGE IS BLANK
Instructions and Parts List Important Safety Information 3M-Matic ™ Accuglide 3 ™ BEFORE INSTALLING OR OPERATING THIS EQUIPMENT Read, understand, and follow all safety and operating instructions. Upper and Lower High Speed Taping Heads 2 Inch Type 10800 Serial No._____________________________________ Spare Parts It is recommended you immediately order the spare parts listed in the "Spare Parts/Service Information" section.
Replacement Parts and Service Information To Our Customers: This is the 3M-Matic™/AccuGlide™/Scotch® equipment you ordered. It has been set up and tested in the factory with Scotch® tapes. If technical assistance or replacement parts are needed, call or fax the appropriate number listed below. Included with each machine is an Instructions and Parts List manual. Technical Assistance / Replacement Parts and Additional Manuals: Call the 3M-Matic™ Help line at 1-800 328-1390.
THIS PAGE IS BLANK
Replacement Parts And Service Information To Our Customers: This is the 3M-Matic™/AccuGlide™/Scotch® equipment you ordered. It has been set up and tested in the factory with Scotch® tapes. If any problems occur when operating this equipment and you desire a service call or phone consultation, call, write, or fax the appropriate number listed below. Included with each machine is an Instructions and Parts List manual.
THIS PAGE IS BLANK
Instruction Manual AccuGlide™ 3 High Speed 2 Inch Upper and Lower Taping Heads Type 10800 Table of Contents Page Replacement Parts and Service Information ............................................................................................ i - ii Table of Contents...................................................................................................................................... iii Equipment Warranty and Limited Remedy .........................................................
Warranty Equipment Warranty and Limited Remedy: Equipment Warranty and Limited Remedy: THE FOLLOWING WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND ANY IMPLIED WARRANTY ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE: 3M sells its AccuGlide™ 3 High Speed 2 Inch Upper and Lower Taping Heads, Type 10800 with the following warranty: 1. 2.
Intended Use size and simplicity of the taping head also makes it suitable for mounting in box conveying systems other than 3M-Matic™ case sealers. This includes replacement of other types of taping, gluing or stapling heads in existing case sealing machines. The AccuGlide™ 3 Upper and Lower Taping Heads - 2 Inch have been designed and tested for use with Scotch® pressure-sensitive film box sealing tape.
THIS PAGE IS BLANK 2
Taping Head Contents AccuGlide™ 3 High Speed 2 Inch Upper and Lower Taping Heads consist of: Qty.
Important Safeguards This safety alert symbol identif es important safety messages in this manual. READ AND UNDERSTAND THEM BEFORE INSTALLING OR OPERATING THIS EQUIPMENT.
Important Safeguards (continued) Important - In the event the following safety labels are damaged or destroyed, they must be replaced to ensure operator safety. See "Replacement Parts Illustrations and Parts Lists" for label part numbers.
Specifications 1. Tape: For use with Scotch® pressure-sensitive film box sealing tapes. 2. Tape Width: 36mm or 1-1/2 inches minimum to 48mm [2 inches] maximum. 3. Tape Roll Diameter: Up to 405mm [16 inches] maximum on a 76.2mm [3 inch] diameter core. (Accommodates all system roll lengths of Scotch® film tapes.) 4. Tape Application Leg Length - Standard: 70mm ± 6mm [2-3/4 inches ±1/4 inch] Tape Application Leg Length - Optional: 50mm ± 6mm [2 inches ± 1/4 inch] (See "Adjustments – Tape Leg Length.
Specifications 405mm [16 in.] Maximum Roll Diameter 443mm [17-7/16 in.] 350mm [13-3/4 in.] 278mm [10-15/16 in.] 33mm [1-19/64 in.] 105mm [4-1/8 in.] 60mm [2-3/8 in.] End View Side View 405mm [16 in.] Maximum Roll Diameter M6 Mounting Holes 76mm [3 in.] 50mm Tape Leg 6mm [1/4 in.] Maximum 18mm [11/16 in.] 76mm [3 in.] 95mm [4 3/4 in.} Box Feed Direction *120mm [4 3/4 in.] Minimum Standard Head Spacing 18mm [11/16 in.] 6mm [1/4 in.] Maximum 445mm [17-1/2 in.] 648 mm [25-1/2 in.
Installation WARNING • To reduce the risk associated with sharp blade hazards: - Keep hands and fingers away from tape cutoff blades under orange blade guards. The blades are extremely sharp Receiving And Handling 3. Figure 2-1 illustrates the typical mounting relationship for opposing taping head assemblies to allow taping of box heights down to 90mm [3-1/2 inches].
Operation Tape Drum Tape Supply Roll Tape Adhesive Side One-Way Tension Roller Applying Mechanism Spring Tension Wrap Roller Buffing Arm Cover Knurled Roller Wrap Roller Buffing Roller Threading Needle Applying Roller Tape Cut-Off Knife Orange Knife Guard Figure 3-1 Taping Head Components/Threading Diagram - Upper Head (Left Side) View) Orange Knife Guard Tape Cut-Off Knife Applying Roller Threading Needle Buffing Roller Wrap Roller Buffing Arm Cover Knurled Roller Tension Wrap Roller Applying
Operation (continued) WARNING • To reduce the risk associated with shear, pinch, and entanglement hazards: − Turn air and electrical supplies off on associated equipment before performing any adjustments, maintenance, or servicing the machine or taping heads − Never attempt to work on the taping heads or load tape when the box drive system is running • To reduce the risk associated with sharp blade hazards: − Keep hands and fingers away from tape cutoff blades under orange blade guards.
Operation (continued) Figure 3-4 Place tape roll on tape drum to dispense tape with adhesive side forward. Seat tape roll fully against back flange of drum. Adhere tape lead end to threading needle as shown. Figure 3-4 – Tape Loading/Threading WARNING • To reduce the risk associated with sharp blade hazards: - Keep hands and fingers away from tape cutoff blades under orange blade guards. The blades are extremely sharp.
Maintenance WARNING • To reduce the risk associated with shear, pinch, and entanglement hazards: − Turn air and electrical supplies off on associated equipment before performing any adjustments, maintenance, or servicing the taping heads Never attempt to work on the taping head or load tape while the box drive system is running − • − To reduce the risk associated with sharp blade hazards: Keep hands and fingers away from tape cutoff blades under orange blade guards. The blades are extremely sharp 3.
Maintenance (continued) WARNING • To reduce the risk associated with shear, pinch, and entanglement hazards: − Turn air and electrical supplies off on associated equipment before performing any adjustments, maintenance, or servicing the taping heads Never attempt to work on the taping head or load tape while the box drive system is running − • − To reduce the risk associated with sharp blade hazards: Keep hands and fingers away from tape cutoff blades under orange blade guards.
Adjustments WARNING • To reduce the risk associated with shear, pinch, and entanglement hazards: - Turn air and electrical supplies off associated equipment before performing any adjustments, maintenance, or servicing the machine or taping heads. Never attempt to work on the taping head or load tape while the box drive system is running - Figure 5-1 – Tape Latch Alignment Tape Latch Alignment – Figure 5-1 The Latching tape drum assembly is pre-set to accommodate 48mm [2 inch] wide tape.
Adjustments (continued) WARNING • To reduce the risk associated with shear, pinch, and entanglement hazards: - Turn air and electrical supplies off associated equipment before performing any adjustments, maintenance, or servicing the machine or taping heads. Never attempt to work on the taping head or load tape while the box drive system is running - A Applying Mechanism Spring To obtain access to the spring, remove the taping head cover (four mounting screws). Replace cover when finished.
Adjustments (continued) WARNING • To reduce the risk associated with shear, pinch, and entanglement hazards: - Turn air and electrical supplies off associated equipment before performing any adjustments, maintenance, or servicing the machine or taping heads.
Troubleshooting Troubleshooting Guide Problem Cause Correction The tape leg on the front of the case is too long The tape is threaded incorrectly The tape must go around the wrap roller before going around the one-way tension roller The tape tension is too low Adjust the one-way tension roller The knurled roller drags Check for adhesive build-up between the knurled roller and its shaft. Clean and lubricate shaft. Remove all lubricant from roller surfaces.
Troubleshooting (continued) Troubleshooting Guide Problem Cause Correction Tape is tabbing on the trailing leg on the back of the box There is excess tension on the tape drum assembly and/or the one-way tension roller assembly Adjust the one-way tension roller and/or the tape drum assembly Rollers in the tape path do not rotate freely Clean adhesive deposits from the surface, ends, and shafts of the rollers. Then lubricate roller shafts. Remove all lubricant from roller surfaces.
Spare Parts/Service Information Recommended Spare Parts Listed are a set of spare parts that will periodically require replacement due to normal wear. These parts should be ordered to keep the taping heads in production: AccuGlide™ 3 Upper Taping Head - 2 inch Qty. Part Number Description 4 1 1 2 1 78-8076-4500-3 78-8137-3311-6 78-8017-9173-8 78-8052-6602-6 78-8076-4726-4 Stud – Mounting Spring – Upper Extension Blade – 65mm/2.
Replacement Parts Illustrations and Parts Lists AccuGlide™ 3 High Speed 2 Inch Upper Taping Head, Type 10800 AccuGlide™ 3 High Speed 2 Inch Lower Taping Head, Type 10800 1. Refer to the Taping Head Assemblies Figure to find all the parts illustrations identified by f gure numbers. 2. Refer to the figure or figures to determine the individual parts required and the parts reference number. 3.
AccuGlide™ 3 - 2" Tape Head AccuGlide™ 3 - 2 inch Figure 10401 Figure 10925 (Haute) Figure 10924 (Bas) Figure 10923 Figure 10919 (Haute) Figure 10920 (Bas) AccuGlide 3 - 2" - NA Figure 10921 21 Figure 10922 2012 January
AccuGlide™ 3 - 2" 26 27 3 28 2 4 29 8 1 29 27 17 19 17 18 15 16 25 11 24 12 13 13 13 13 10 21 20 9 5 7 23 23 Figure 10925 – Upper Head AccuGlide 3 - 2" - NA 22 2012 January
AccuGlide™ 3 - 2" Figure 10925 – 2" Upper Head Ref. No. 3M Part No.
AccuGlide™ 3 - 2" 1 7 2 8 9 8 16 4 5 16 3 4 9 6 15 14 12 13 12 11 10 15 Figure 10922 – Upper and Lower Heads AccuGlide 3 - 2" - NA 24 2012 January
AccuGlide™ 3 - 2" Figure 10922 – 2" Upper and Lower Heads Ref. No. 3M Part No.
AccuGlide™ 3 - 2" 1 7 2 8 9 8 16 4 5 16 3 4 9 6 15 14 12 13 12 11 10 15 Figure 10919 – Upper Head AccuGlide 3 - 2" - NA 26 2012 January
AccuGlide™ 3 - 2" Figure 10919 – 2" Upper Head Ref. No. 3M Part No.
AccuGlide™ 3 - 2" 6 6 1 3 7 8 7 9 5 4 5 4 9 Figure 10923 10923 – – Upper Upper and and Lower Lower Heads Heads Figure AccuGlide AccuGlide 3 3 -- 2" 2" -- NA NA 28 28 2012 2011 January July
AccuGlide™ 3 - 2" Figure 10923 – 2" Upper and Lower Heads Ref. No. 3M Part No. Description 10923-1 78-8137-3302-5 Link – Assembly 10923-3 78-8137-3304-1 Shaft – Pivot, Buffing 10923-4 78-8017-9082-1 Bearing – Special 30 mm 10923-5 78-8017-9106-8 Screw – Bearing Shoulder 10923-6 26-1003-5829-5 Screw – Hex Hd, M6 x 12 10923-7 78-8137-3305-8 Spacer – Applying Pivot 10923-8 78-8137-3306-6 Shaft – Pivot, Applying 10923-9 78-8094-6151-6 Washer - Flat, 6.5 ID x 15 OD x 0.
AccuGlide™ 3 - 2" Figure 10921 – Upper and Lower Heads AccuGlide 3 - 2" - NA 30 2012 January
AccuGlide™ 3 - 2" Figure 10921 – 2" Upper and Lower Heads Ref. No. 3M Part No. Description 10921-1 78-8137-3307-4 Frame – Cut-Off Weldment 10921-2 78-8017-9173-8 Blade – 65 mm/2.56 Inch 10921-3 26-1003-8596-7 Screw - Hex Hd M5 x 8 w/ Ext.
AccuGlide™ 3 - 2" 14 3 1 13 12 13 13 13 4 14 16 7 5 2 6 7 7 11 15 10 9 8 4 Figure 10401 – Upper and Lower Heads AccuGlide 3 - 2" - NA 32 2012 January
AccuGlide™ 3 - 2" Figure 10401 – 2" Latch Upper and Lower Heads Ref. No. 3M Part No.
AccuGlide™ 3 - 2" 23 23 7 5 9 10 21 20 13 13 13 12 24 25 16 15 11 19 17 18 17 27 29 29 8 1 4 3 13 2 28 27 26 26 Figure 10924 – Lower Head AccuGlide 3 - 2" - NA 34 2012 January
AccuGlide™ 3 - 2" Figure 10924 – 2" Lower Head Ref. No. 3M Part No.
AccuGlide™ 3 - 2" 7 3 4 7 7 6 9 9 7 8 7 5 7 2 1 Figure 10920 – Lower Head AccuGlide 3 - 2" - NA 36 2012 January
AccuGlide™ 3 - 2" Figure 10920– Lower Head Ref. No. 3M Part No.
THIS PAGE IS BLANK 38
39
40