User's Manual

ManualsBrands3M ManualsElectronicsModel 1200 Digital Media Detagger

DigitalMediaDetaggerModel1200

Owner’sManual

Summary of content (23 pages)

PAGE 1
Digital Media Detagger Model 1200 Owner’s Manual
PAGE 3
Contents Safety ............................................................................................................................................. Intended use ................................................................................................................................. Explanation of signal word consequences ....................................................................................... Explanation of product safety label symbols .......................................
PAGE 5
Safety Keep this manual for future reference! Read, understand, and follow all safety information contained in these instructions prior to installation and use of the 3M™ Digital Media Detagger Model 1200. Retain these instructions for future reference. Intended use The 3M™ Digital Media Detagger Model 1200 is designed and tested for use in processing library materials with RFID tags. It was designed for use in an indoor library environment and has not been tested for other uses or environments.
PAGE 6
Safety Safety messages contained in this manual WARNING To reduce the risk of exposure to hazardous voltage and/or fire while operating the device, observe the following rules: • Because this unit contains high voltage and the risk of electrical shock, do not remove electrical panels. This unit has no user serviceable parts. It is serviceable by certified 3M technicians only. • Ensure access to the power cord. The unit has no on/off switch. • If the device is dropped, unplug it and do not use it.
PAGE 7
Safety Label locations Model 1200 Digital Media Detagger 100-240V~ max. 0,6 A 50 / 60 Hz S/N: XXXXXXX 3M Library Systems St. Paul, Minnesota 55144 Made in USA 1200 Label Placement Figure 1 Label location Copyright © 2008. 3M. All rights reserved.
PAGE 9
Regulatory information FCC intentional radiator certification FCC ID: DGFTTS1200 [To be determined] This equipment contains an intentional radiator approved by the FCC under the FCC ID number shown above. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NO MODIFICATIONS.
PAGE 11
Site planning Environmental specifications Temperature (operating) 32°F to 104°F (0°C to 40°C) Temperature (storage) -40°F to 131°F (-40°C to 55°C) Relative humidity (operation) 5% to 95% RH, non-condensing Relative humidity (storage) 5% to 99% RH, non-condensing Electrical specifications 100 – 240 VAC, 0.6 A max, 50/60 Hz Dimensions and weight Depth 13.4 in. (34 cm) Height 12.2 in. (31 cm) Width 9 in. (23 cm) Weight 15 lbs. (7 kg) Copyright © 2008. 3M. All rights reserved.
PAGE 12
Site planning Mounting options The Detagger Model 1200 can be imbedded in a counter or mounted on a table top. Figure 2 In-counter installation WARNING Do NOT use mounting material with in-counter installations.
PAGE 13
Operation Model 1200 orientation The Digital Media Detagger allows patrons to quickly and efficiently process CD/DVD cases secured with the Red Tag system. Setup The Digital Media Detagger does not have a power cord. To turn it on, simply apply power. DANGER This equipment contains high voltage. Risk of electric shock. Do not remove protective panels. Serviceable only by certified 3M technicians. No user-serviceable parts. 1. Connect the power cord to the power receptacle at the rear of the unit.
PAGE 14
Operation The status light • The status light turns green when a case is processed correctly. • The status light flashes red until a processed item is removed from the unit. Status Light • The status light turns red and the Red Tag is not removed when the unit detects a case that was not processed correctly on the Self Check system. 1200 Gr status light 10 Copyright © 2008. 3M. All rights reserved.
PAGE 17
Cleaning To clean the unit, do the following: 1. Remove power from the Digital Media Detagger by unplugging the unit. 2. Using a damp cloth (with or without mild detergent), wash all outside surfaces. Copyright © 2008. 3M. All rights reserved.
PAGE 19
Troubleshooting Here are some things to try if you have trouble with the unit. Condition: no status light or status light always red • Check the power cord. • Unplug the unit, wait 10 seconds, and then supply power again. • Call 3M Service. See 3M Service phone numbers on page 19. Condition: cannot process the case; Red Tag cannot be removed • Check to see if a Red Tag strip was left in the unit after the last processing. . • Unplug the unit, wait 60 seconds, and then supply power again.
PAGE 21
Warranty Effective 12-12-05 One Year Library Systems Product Performance Guarantee: Subject to the Limitation of Liability below, 3M guarantees your satisfaction with the performance of any 3M Library System Product for 12 months from the date of installation provided that a) you are the original purchaser: b) you have executed a one (1) year 3M Service Agreement for maintenance of the Library System product; and c) the product has not been subjected to abuse, misuse, accident or neglect.
PAGE 23
3M Service Once the facility is ready for installation, call 3M Service to arrange for installation and setup. 3M Service phone numbers For questions regarding your system, call one of the following numbers. In the United States In Canada In other countries 1-800-328-0067 English 1-800-268-6235 Français 1-800-567-3193 Call your local 3M office. Returning a unit for repair Need information on where to return the unit and any other requirements.