User Manual Innovative LCD Display Solutions AP—10AV Series DP—10AV Series OP—10AV Series UMUV.
AP-10AV / DP-10AV / DP-10AV Series User Manual 1. Table of Content 1. Table of Content 2. Introduction A) B) C) D) 3. Page.1 Overview Features Dimension Diagrams Technical Specifications Installation A) Package Contents B) Caution to the user C) Cleaning D) Precautions 4. Page.7 Page.7 Page.7 Page.
AP-10AV / DP-10AV / DP-10AV Series User Manual 2. Introduction A. Overview This LCD monitor incorporates 10.4”color active matrix thin-film-transistor (TFT) liquid crystal display to provide superior display performance. A maximum resolution of 800 x 600 is ideal for displaying complex graphics and high definition images. Other outstanding designs that enhance this LCD monitor’s performance are Plug & Play compatibility and OSD (On Screen Display) controls. B.
AP-10AV / DP-10AV / DP-10AV Series User Manual 2. Introduction C. Dimension Diagrams AP-10AV series Apr 05 P.
AP-10AV / DP-10AV / DP-10AV Series User Manual 2. Introduction C. Dimension Diagrams DP-10AV series Apr 05 P.
AP-10AV / DP-10AV / DP-10AV Series User Manual 2. Introduction C. Dimension Diagrams OP-10AV series Apr 05 P.
AP-10AV / DP-10AV / DP-10AV Series User Manual 2. Introduction Technical Specifications Monitor Power Supply Connectors Video Panel 10.4" LCD Panel Display Type TFT LCD active matrix colour Resolutions 800 x 600 Response Time Tr=15ms, Tf=25ms Contrast Ratio 180:1 typical Brightness 350 cd/m2 typical Pixel Pitch 0.264(H) x 0.264(V) Panel Colour 262,144 display colour Viewing Angle 60 / 60 / 55 / 40 (L / R / U / D) Storage Temp. -20° to 60°C Operating Temp.
AP-10AV / DP-10AV / DP-10AV Series User Manual 3. Installation A. Package Contents After unpacking the carton, check and see if the following items are included in good condition. Contact your supplier as soon as possible for replacing the missing / damaged items. ● 10.
AP-10AV / DP-10AV / DP-10AV Series User Manual 3. Installation D. Precautions Read all of these instructions and save them for later use. Follow all warnings and instructions on the product. Product ● Do not cover or block the vent holes in the case. ● Do not insert sharp objects or spill liquid into the LCD monitor through cabinet slots. They may cause accident fire, electric shock or failure. ● Disconnect the power plug from the AC outlet if you will not use it for an indefinite period of time.
AP-10AV / DP-10AV / DP-10AV Series User Manual 3. Installation D. Precautions (Cont.) Power and extension cords 1. Do not allow anything to rest on the power cord. 2. Do not locate this product where persons will walk on the cord. 3. Use the proper power cord with correct attachment plug type. If the power source is 120V AC, use a power cord that has UL and C-UL approvals.
AP-10AV / DP-10AV / DP-10AV Series User Manual 3. Installation A. Product Views AP Series - Front View AP Series - Rear View Apr 05 P.
AP-10AV / DP-10AV / DP-10AV Series User Manual 3. Installation A. Product Views (Cont.) DP Series - Front View DP Series - Rear View Apr 05 P.
AP-10AV / DP-10AV / DP-10AV Series User Manual 3. Installation A. Product Views (Cont.) OP Series - Front View OP Series - Rear View Apr 05 P.
AP-10AV / DP-10AV / DP-10AV Series User Manual 4. Using the System B. I/O Outlet AP Series DP Series OP Series (1) 1. 2. 3. 4. 5. 6. Apr 05 DC IN PC IN RCA IN S-Video IN USB IN SERIAL IN (2) (3) (4) (5) (6) ： Connect to DC power cable. ： Connect to D-Sub 15 pin signal connector. ： Connect to the composite cable connector. (for AV series only) ： Connect to the S-Video cable connector. (for AV series only) ： Connect to the USB connector.
AP-10AV / DP-10AV / DP-10AV Series User Manual 4. Using the System C. Installation Procedures This monitor is equipped with an auto-sensing power supply for voltage ranges 100~240V, 50~60Hz. Please follow the following instruction to install LCD monitor. 1. Make sure that the system power is turned off. 2. Plug the signal cable to the signal connector at the rear of PC and the rear of the LCD monitor. 3. Plug adapter output cable to the jack at the rear of LCD monitor and the power cord to the adapter.
AP-10AV / DP-10AV / DP-10AV Series User Manual 4. Using the System D. Setup Touchscreen Touchscreen used for UltraView products are manufactured by 3M. Here provide TouchWareTM Software includes touch screen drivers for your installing.
AP-10AV / DP-10AV / DP-10AV Series User Manual 4. Using the System D. Setup Touchscreen For Windows 95, 98, Me, NT4.0, 2000 & XP (Cont.) 7. Once installation is complete, restart the system. As the system restarts, Windows detects and loads the driver. ● For serial controllers, restart the system. As the system restarts, Windows detects and load the driver Note: This step is not necessary for Windows 2000 or above system, The driver loads automatically.
AP-10AV / DP-10AV / DP-10AV Series User Manual 4. Using the System D. Setup Touchscreen For DOS (Cont.) 7. Type INSTALL followed by the source disk drive, the destination drive, and the destination directory. For example, the following command copies the files from Drive A (source drive) to Drive C (destination drive) and the \MTS\TOUCH directory : INSTALL A: C:\MTS\TOUCH 8. 9. Press Enter.
AP-10AV / DP-10AV / DP-10AV Series User Manual 4. Using the System D. Setup Touchscreen For DOS (Cont.) Loading the DOS Touchscreen Driver After you install the files for the DOS touchscreen driver, you must load the driver before you can run a DOS touch application or open the DOS Touchscreen control panel. You can run the DOS touchscreen driver from a full-screen DOS session within Windows. However, the Windows touchscreen driver cannot be running. Error message reads: “Windows x.
AP-10AV / DP-10AV / DP-10AV Series User Manual 4. Using the System E. OSD Switch Power Left Apr 05 Menu/Selection Right Exit Input Select: This button is used to select CVBS for composite video input, RGB for VGA input and S-Video for Super-Video input OSD Menu: This button is used to enter OSD main Menu Increase(à): This button is used to adjust the increasing or next value of selected OSD control option.
AP-10AV / DP-10AV / DP-10AV Series User Manual 4. Using the System F.
AP-10AV / DP-10AV / DP-10AV Series User Manual 4. Using the System F. OSD Control For VGA Input Version Bright / Contrast 1. Brightness ● To perform brightness adjustment of the input RGB signal ● Use the Left & Right button to adjust and button to “Brightness” 2. Contrast ● To adjust the contrast level of the input signal ● Use the Left & Right button to adjust and button to “Contrast” Phase / Clock 1.
AP-10AV / DP-10AV / DP-10AV Series User Manual 4. Using the System F. OSD Control For VGA Input Version MISC 1. Information ● ● ● The first header row shows the current resolution setup The second header row shows the horizontal frequency of the current input signal The third header row shows the vertical frequency of the current input signal 2. OSD Timer ● To modify the duration of the OSD time-out 3.
AP-10AV / DP-10AV / DP-10AV Series User Manual 4. Using the System G. OSD Control For Video Input Version Colour Configuration Page Colour Brightness Contrast Colour Adjust Exit Brightness ︰ Adjust the brightness value from 1 to 100 using (à) and (ß) buttons. Contrast ︰ Adjust the contrast value from 1 to 100 using (à) and (ß) buttons. Colour Adjust ︰ Select the colour temperature option for 9300K or 6500K or RGB Exit ︰ Exit the Colour configuration Page Apr 05 P.
AP-10AV / DP-10AV / DP-10AV Series User Manual 4. Using the System G. OSD Control For Video Input Version Picture Configuration Page Picture H.Position V.Position Sharpness Phase Clock Exit H.Position ︰ Press (à) shifting display image to right with value from 0 to 100; Press (ß) shifting display image to left from value 0 to 100. V.Position ︰ Press (à) shifting display image to upward with value from 0 to 100; Press (ß) shifting display image to downward from value 0 to 100.
AP-10AV / DP-10AV / DP-10AV Series User Manual 4. Using the System G. OSD Control For Video Input Version Function Configuration Page Function Auto Adjust Auto Position Auto Phase Auto Clock Exit Auto Adjust ︰ Enable or disable function for auto adjusting brightness, contrast, color etc.
AP-10AV / DP-10AV / DP-10AV Series User Manual 4. Using the System G. OSD Control For Video Input Version OSD Menu Configuration Page OSD Menu Language OSD H.Position OSD V.Position OSD Timer Translucent Exit Language ︰ Change language of OSD Menu for English or traditional Chinese OSD H.Position ︰ Press (") shifting OSD Menu to right with value from 0 to 100; Press (!) shifting OSD Menu to left from value 0 to 100. OSD V.
AP-10AV / DP-10AV / DP-10AV Series User Manual 4. Using the System G. OSD Control For Video Input Version Miscellaneous Configuration Page Miscellaneous Mode Select Reset Exit Mode Select ︰ Switch the display size for 640 x 400 or 720 x 400 in DOS mode Reset ︰ Enter for reloading all factory default Exit ︰ Exit the Function configuration Page Apr 05 P.
