X90w Multimedia Projector Network Functions This manual is only intended to explain Network Functions. For safety, operations or any other issues, refer to the all user's manual for this projector. WARNING • Before using the network functions, read the all user's manual for this projector carefully to ensure your projector is set up correctly. • After reading, keep the manuals in a safe place for future reference. NOTE • The information in this manual is subject to change without notice.
3M™ Digital Projector X90 Network Functions Network Functions This projector is equipped with the following network functions. Configuring and Controlling the Projector via a Web Browser You can change the settings of or control the projector via a network by using a web browser from a PC that is connected to the same network.
M™ Digital Projector X90 Network Functions Before using the network functions… To use the network functions of this projector, the projector must be configured to suit your network. Consult with your network administrator before connecting the projector to your network. Incorrect network configuration of this projector may cause problems on your network.
3M™ Digital Projector X90 Network Functions Configuring and controlling the projector via a web browser You can adjust or control the projector via a network from a web browser on a PC that is connected to the same network. NOTE • Internet Explorer 5.5 or higher or Netscape 6.2 or higher are required. • If JavaScript is disabled in your web browser configuration, you must enable JavaScript in order to use the projector web pages properly.
3M™ Digital Projector X90 Network Functions Configuring and controlling the projector via a web browser (Continued) When configuring or controlling the projector via a web browser, an ID and password are required. There are two types of IDs, Administrator IDs and User IDs. The following chart describes the differences between user and administrator IDs. Item Description Displays the projector’s current Network Information network configuration settings.
3M™ Digital Projector X90 Settings Settings Refer to the following for configuring or controlling the projector via a web browser. Example: If the IP address of the projector is set to 192.168.1.10: 1) Enter [https://192.168.1.10] into the address bar of the web browser and the screen in Fig. 1 will be displayed. 2) Enter your ID and password and click [Logon]. Fig. 1 If the logon is successful either the Fig.2 or Fig.3 screen will be displayed. Fig. 2 (Logon with administrator ID) Fig.
3M™ Digital Projector X90 Settings Network Information All screen images displayed in this manual are screens of a logon using an administrator ID. Any administrator only functions will not be displayed when using a user ID. Refer to the descriptions in each table. Displays the projector’s current network configuration settings. Item Description DHCP Displays the DHCP configuration settings. IP Address Displays the current IP address. Subnet Mask Displays the Subnet Mask.
3M™ Digital Projector X90 Settings Network Settings Displays and configures network settings. Item IP Configuration Description Configures network settings. DHCP ON Enables DHCP. DHCP OFF Disables DHCP. IP Address Configures the IP address when DHCP is disabled. Subnet Mask Configures the Subnet Mask when DHCP is disabled. Default Gateway Configures the Default Gateway when DHCP is disabled. Projector Name Configures the Projector name.
3M™ Digital Projector X90 Settings Port Settings Displays and configures communication port settings. Item Network Control Port1 (Port:23) Description Configures command control port 1 (Port:23). Port open Click the [Enable] check box to use port 23. Authentication Click the [Enable] check box when authentication is required for this port. Network Control Port2 (Port:9715) Configures command control port 2 (Port:9715). Port open Click the [Enable] check box to use port 9715.
3M™ Digital Projector X90 Settings Mail Settings Displays and configures e-mail addressing settings. Item Description Send Mail Click the [Enable] check box to use the e-mail function. Configure the conditions for sending email under [Alert Settings]. SMTP Server IP Address Configures the address of the mail server in IP format. Sender E-mail address Configures the sender e-mail address. The length of the sender e-mail address can be up to 255 alphanumeric characters.
3M™ Digital Projector X90 Settings Alert Settings Displays and configures failure & warning alerts. Item Cover Error Description Configures Cover Error alert settings. SNMP Trap Click the [Enable] check box to enable SNMP Trap alerts for this item. Send Mail Click the [Enable] check box to enable e-mail alerts for this item. Mail Subject Configures the subject line of the e-mail to be sent. The length of the subject line can be up to 255 alphanumeric characters.
3M™ Digital Projector X90 Settings Alert Settings (Continued) Item Lamp Error Configures Lamp Error alert settings. SNMP Trap Click the [Enable] check box to enable SNMP Trap alerts for this item. Send Mail Click the [Enable] check box to enable e-mail alerts for this item. Mail Subject Configures the subject line of the e-mail to be sent. The length of the subject line can be up to 255 alphanumeric characters. Mail Text Configures the text of the e-mail to be sent.
3M™ Digital Projector X90 Settings Alert Settings (Continued) Item Lamp Time Error Description Configures Lamp Time Error alert settings. SNMP Trap Click the [Enable] check box to enable SNMP Trap alerts for this item. Send Mail Click the [Enable] check box to enable e-mail alerts for this item. Mail Subject Configures the subject line of the e-mail to be sent. The length of the subject line can be up to 255 alphanumeric characters. Mail Text Configures the text of the e-mail to be sent.
3M™ Digital Projector X90 Settings Alert Settings (Continued) Item Other Error Description Configures Other Error alert settings. SNMP Trap Click the [Enable] check box to enable SNMP Trap alerts for this item. Send Mail Click the [Enable] check box to enable e-mail alerts for this item. Mail Subject Configures the subject line of the e-mail to be sent. The length of the subject line can be up to 255 alphanumeric characters. Mail Text Configures the text of the e-mail to be sent.
3M™ Digital Projector X90 Settings Alert Settings (Continued) Item Filter Time Alarm Description Configures Filter Time Alarm alert settings. Alarm Time Configures the filter time to alert. SNMP Trap Click the [Enable] check box to enable SNMP Trap alerts for this item. Send Mail Click the [Enable] check box to enable e-mail alerts for this item. Mail Subject Configures the subject line of the e-mail to be sent. The length of the subject line can be up to 255 alphanumeric characters.
3M™ Digital Projector X90 Settings Schedule Settings Displays and configures schedule settings. Item Daily Configures the daily schedule. Schedule Click the [Enable] check box to enable daily scheduling. Schedule List Displays the current daily schedule. Sunday Configures the Sunday schedule. Schedule Click the [Enable] check box to enable Sunday scheduling. Schedule List Displays the current Sunday schedule. Monday Configures the Monday schedule.
3M™ Digital Projector X90 Settings Schedule Setting (Continued) Item Specific date No1 Description Configures the specific date (No.1) schedule. Schedule Click the [Enable] check box to enable specific date (No.1) scheduling. Month/Day Configures the Month and date. Schedule List Displays the current specific date (No.1) schedule. Specific date No.2 Configures the specific date (No.2) schedule. Schedule Click the [Enable] check box to enable specific date (No.2) scheduling.
3M™ Digital Projector X90 Settings Schedule Setting (Continued) To add additional functions and events click the [Add] button and set the following items. Item Description Time Configures the time to execute commands. Command Configures the commands to be executed. Power Parameter Configures the parameters for power control. Input Source Parameter Configures the parameters for input switching. Display Image Parameter Configures the parameters for display of transfer image data.
3M™ Digital Projector X90 Settings Date/Time Settings (Continued) Item Daylight Savings Time Start Description Click the [ON] check box to enable daylight savings time and set the following items. Configures the date and time daylight savings time begins. Month Configures the month daylight savings time begins (1~12). Week Configures the week of the month daylight savings time begins (First, 2, 3, 4, Last).
3M™ Digital Projector X90 Settings Security Settings Displays and configures passwords and other security settings. Item Administrator authority Description Configures the Administrator ID and Password. Administrator ID Configures the Administrator ID. The length of the text can be up to 32 alphanumeric characters. Administrator Password Configures the Administrator Password. The length of the text can be up to 255 alphanumeric characters.
3M™ Digital Projector X90 Settings Security Settings (Continued) Item Network Control Authentication Password Description Configures the Authentication Password for the command control. Configures the Authentication Password. The length of the text can be up to 16 alphanumeric characters. Re-enter Authentication Used to re-enter the above password for verification. Password SNMP Community Name Configures the community name if SNMP is used. Configures the community name.
3M™ Digital Projector X90 Projector Control Projector Control Projector Control The items shown in the table below can be performed using the [Projector Control] menu. Select an item using the up and down arrow keys on the PC. Most of the items have a submenu. Refer to the table below for details. Controls the projector. Item Description Main Power Turns the power On/Off. Input Source Selects the input source. Picture Mode Selects the Picture Mode setting. Blank On/Off Turns Blank On/Off.
3M™ Digital Projector X90 Projector Control Projector Control (Continued) Item Description Image Aspect Selects the Aspect setting. Over Scan Selects the Over Scan setting. V Position Adjusts the V Position. H Position Adjusts the H Position. H Phase Adjusts the H Phase. H Size Adjusts the H Size. Auto Adjust Performs Auto Adjustment. Input Progressive Selects the progressive setting. Video NR Selects the Video NR setting. 3D-YCS Selects the 3D-YCS setting.
3M™ Digital Projector X90 Projector Control Projector Control (Continued) Item Description Audio Volume Adjusts the Volume setting. Treble Adjusts the Treble setting. Bass Adjusts the Bass setting. SRS WOW Selects the SRS WOW setting. Speaker Turns Speaker On/Off. Audio-RGB1 Assigns the Audio-RGB1 input terminal. Audio-RGB2 Assigns the Audio-RGB2 input terminal. Audio-M1-D Assigns the Audio-M1-D input terminal. Audio-Video Assigns the Audio-Video input terminal.
3M™ Digital Projector X90 Projector Control Projector Status Displays and configures the current projector status. Item Description Error Status Displays the current error status Lamp Time Displays the usage time for the current lamp. Filter Time Displays the usage time for the current filter. Power Status Displays the current power status. Input Status Displays the current input signal source. Blank On/Off Displays the Blank On/Off status. Mute Displays the current Mute On/Off status.
3M™ Digital Projector X90 Failure & Warning Alerts via E-mail Failure & Warning Alerts via E-mail The projector can automatically send an alert to specified e-mail addresses when the projector requires maintenance or has encountered an error. NOTE • Up to five e-mail addresses can be specified. • The projector may be not able to send e-mail if the projector suddenly loses power. Mail Settings (10) To use the projector’s e-mail function please configure the following items via a web browser.
3M™ Digital Projector X90 Failure & Warning Alerts via E-mail Mail Settings (Continued) 8) Configure the Failure/Warning Alerts via E-mail settings. Click [Alert Settings] on the main menu. 9) Select and configure each alert item. Refer to [Alert Settings] in [Configuring and Controlling the Projector via a Web Browser] for further information. 10) Click the [Apply] button to save the settings.
3M™ Digital Projector X90 Projector management via SNMP Projector management via SNMP When SNMP is enabled, the projector is able to send Failure/Warning Alerts to a specified PC. NOTE • It is recommended that SNMP functions be carried out by a network administrator. • SNMP management software must be installed on the computer to monitor the projector via SNMP. SNMP settings (9) Configure the following items via a web browser to use SNMP. Example: If the IP address of the projector is set to 192.168.1.
3M™ Digital Projector X90 Controlling the Projector via Scheduling Controlling the Projector via Scheduling The projector can be automatically controlled via scheduling. NOTE • You can schedule the following control events: Power ON/OFF, Input Source and Transferred Image Display. • There are 3 types of Scheduling, 1) daily 2) day of the week 3) specific date. • The priority for scheduled events is as follows 1) specific date 2) day of the week 3) daily.
3M™ Digital Projector X90 Controlling the Projector via Scheduling Date/Time Settings (18) The Date/Time setting can be adjusted via a web browser. Example: If the IP address of the projector is set to 192.168.1.10: 1) Enter [https://192.168.1.10] into the address bar of the web browser. Enter the Administrator ID and Password and click [Logon]. 2) Click [Date/Time Settings] on the main menu and configure each item.
3M™ Digital Projector X90 Controlling the Projector via Scheduling Schedule Settings (16) Schedule settings can be configured from a web browser. Example: If the IP address of the projector is set to 192.168.1.10: 1) Enter [https://192.168.1.10] into the address bar of the web browser. 2) Enter the Administrator ID and Password and click [Logon]. 3) Click [Schedule Settings] on the main menu and select the required schedule item. 4) Click the [Enable] check box to enable scheduling.
3M™ Digital Projector X90 e-SHOT (Still Image Transfer) Display e-SHOT (Still Image Transfer) Display The projector can display a still image that is transferred via the network. Communication Port The following port is used for e-SHOT. TCP #9716 (9) NOTE • e-SHOT is not available via communication ports which are used for the command control (TCP #23 and TCP #9715). e-SHOT (Still Image Transfer) Settings Configure the following items from a web browser when e-SHOT is used.
3M™ Digital Projector X90 e-SHOT(Still Image Transfer) Display e-SHOT (Still Image Transfer) Settings (Continued) When the authentication setting is enabled, the following settings are required. 6) Click [Security Settings] on the main menu. 7) Select [Network Control] and enter the desired authentication password. * see Note1 8) Click the [Apply] button to save the settings.
3M™ Digital Projector X90 Command Control via the Network Command Control via the Network You can configure and control the projector via the network using RS-232C commands. Communication Port The following two ports are assigned for the command control. TCP #23 TCP #9715 NOTE • Command control is not available via communication port (TCP #9716) that is used for the e-SHOT transmission function. Command Control Settings (9) Configure the following items from a web browser when command control is used.
3M™ Digital Projector X90 Command Control via the Network Command Control Settings (Continued) When the authentication setting is enabled, the following settings are required. (20) 7) Click [Security Settings] on the main menu. 8) Click [Network Control] and enter the desired authentication password. * See Note1. 9) Click the [Apply] button to save the settings. * See Note2.
3M™ Digital Projector X90 Command Control via the Network Command format Command formats differ among the different communication ports. TCP #23 You can use the RS-232C commands without any changes. The reply data format is the same as the RS-232C commands. However, the following reply will be sent back in the event of authentication failure when authentication is enabled.
3M™ Digital Projector X90 Command Control via the Network Reply Data format The connection ID (the data is same as the connection ID data on the sending data format) is attached to the RS-232C commands reply data.
3M™ Digital Projector X90 Command Control via the Network Automatic Connection Break The TCP connection will be automatically disconnected after there is no communication for 30 seconds after being established. Authentication The projector does not accept commands without authentication success when authentication is enabled. The projector uses a challenge response type authentication with an MD5 (Message Digest 5) algorithm.
3M™ Digital Projector X90 Intended Use Before operating this machine, please read this entire manual thoroughly. The 3MTM Multimedia Projectors are designed, built, and tested for use indoors, using 3M lamps, 3M ceiling mount hardware, and nominal local voltages. The use of other replacement lamps, outdoor operation, or different voltages has not been tested and could damage the projector peripheral equipment and/or create a potentially unsafe operating condition.
