User Manual

ManualsBrands3xLOGIC ManualsVideoVISIX Camera

!"#$%&&%$'(")* % " +% &),!"#$#%!&'()*+,!-./'+.!

-.//0)12#$3((4)54'627)8+'$2)9..7)12#$3'"#$247):;)<../-),)===>9?&(@'A>A(3),)B<CCD)9EF;G!:)

"#$#%! &'()*+,!-./'+.!

#01(.22.(3*0!4.05.2!

! !

Summary of content (103 pages)

PAGE 1
Installation Manual | VISIX Network Camera VISIX Network Camera Installation Manual 10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.
PAGE 2
Installation Manual | VISIX Network Camera Thank you for purchasing our product. If there are any questions or requests, please do not hesitate to contact your dealer. Please see Section 2 of this guide for a list of all 3xLOGIC cameras covered in this manual. This manual may contain technical inaccuracies or printing errors.
PAGE 3
Installation Manual | VISIX Network Camera Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules.
PAGE 4
Installation Manual | VISIX Network Camera Safety Instruction These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss. The precaution measure is divided into ‘Warnings’ and ‘Cautions’: Warnings: Serious injury or death may be caused if any of these warnings are neglected.
PAGE 5
Installation Manual | VISIX Network Camera Cautions: ! Make sure the power supply voltage is correct before using the camera. ! Do not drop the camera or subject it to physical shock. ! Do not touch sensor modules with fingers. If cleaning is necessary, use a clean cloth with a bit of ethanol and wipe it gently.
PAGE 6
Installation Manual | VISIX Network Camera Table of Contents 1 INTRODUCTION .......................................................................................................................................... 8 1.1 APPLICATIONS ................................................................................................................................................... 8 1.2 PREPARATIONS ....................................................
PAGE 7
Installation Manual | VISIX Network Camera 6 OUTDOOR DOME CAMERA INSTALLATION ................................................................................................ 52 6.1 TYPE I OUTDOOR DOME CAMERA ....................................................................................................................... 52 Applicable Camera Models ..................................................................................
PAGE 8
Installation Manual | VISIX Network Camera Available Mounts .......................................................................................................................................... 90 Installation .................................................................................................................................................... 90 9 MOUNT SCHEMATICS ............................................................................
PAGE 9
Installation Manual | VISIX Network Camera 1 Introduction The network camera is an embedded digital surveillance camera that combines the features of both the traditional analog camera and the encoder.
PAGE 10
Installation Manual | VISIX Network Camera 2 Camera Type Navigation Key 3xLOGIC offers a variety of network camera styles, types and models. The below table features all cameras in 3xLOGIC’s product offering which are covered in this manual.
PAGE 11
Installation Manual | VISIX Network Camera 3 Full Body Camera Installation 3.1 Type I Full Body Camera APPLICABLE CAMERA MODELS. This section applies to the following camera models: ! VSX-‐2MP-‐FE CAMERA DESCRIPTION The overview of Type I Full Body Camera is shown below. Figure 3-‐1 Overview Table 1-‐1 Description No.
PAGE 12
Installation Manual | VISIX Network Camera NOTE: No. Description 14 Grounding 15 RESET: Reset Button Press and hold RESET for 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.
PAGE 13
Installation Manual | VISIX Network Camera Expansion Screw Figure 3-‐3 Attach Camera Mounting Bracket to Ceiling 2). Align the screw threading on the top of the camera with the hole on the bracket arm and use the tightening screw to affix the camera to the bracket. 3).
PAGE 14
Installation Manual | VISIX Network Camera Figure 3-‐5 Install the Lens 3.
PAGE 15
Installation Manual | VISIX Network Camera The interfaces on the rear panel are shown below: 10 9 8 6 11 7 18 17 16 15 13 14 12 Figure 3-‐8 Overview (3) Table 1-‐3 Description No. Description No.
PAGE 16
Installation Manual | VISIX Network Camera Figure 3-‐9 Auto-‐iris Interface Table 1-‐4 Pins No. DC-‐driven 1 Damp-‐ 2 Damp+ 3 Drive+ 4 Drive-‐ Power, Video and GND pins are used when the auto-‐iris is driven by video; Damp+, Damp-‐, Drive+ and Drive-‐ pins are used when the auto-‐iris is driven by DC.
PAGE 17
Installation Manual | VISIX Network Camera Adjustable Nut Figure 3-‐10 Installing the Mount 2) Fit the lens (not supplied) to the camera and rotate it to get it tightened. Install the adapter ring to the lens interface if a C-‐mount lens is used.
PAGE 18
Installation Manual | VISIX Network Camera a. Connect the VIDEO OUT interface of the camera to the debugging monitor. b. Adjust the Zoom Lever and Focus Lever to obtain the desired image on the monitor.
PAGE 19
Installation Manual | VISIX Network Camera Tilt Adjust Table Lock Screw Figure 3-‐14 Remove the Tilt Adjust Table 4) Fit the removed tilt adjust table to the camera, and secure it with two screws. Figure 3-‐15 Install the Tilt Adjust Table 5) Secure the wall mount to the wall with the supplied expansion screws.
PAGE 20
Installation Manual | VISIX Network Camera a. Loosen the pan nut to adjust the pan angle [0 °-‐360°]. b. Loosen the knob on the ceiling mount to adjust the tilt angle [0°-‐±45°]. 8) Adjust the Lens a. Connect the VIDEO OUT interface of the camera to the debugging monitor. b.
PAGE 21
Installation Manual | VISIX Network Camera 4 Indoor Dome Camera Installation 4.
PAGE 22
Installation Manual | VISIX Network Camera 4 MIC IN: Audio input interface 5 D+, D-‐: RS-‐485 interface 6 1A, 1B, 2A, 2B: Alarm output interface 7 IN1, GND, IN2, GND: Alarm input interface 8 Power Supply Interface NOTE: Hold RESET for 10s when the camera is powering on or rebooting to restore the default settings, including the user
PAGE 23
Installation Manual | VISIX Network Camera 1 1 Drill Template A Screw hole 1: for Mounting Base Hole A: for cables routed through the ceiling 1 1 Code:190600249 Figure 4-‐3 Drill Template 3) Affix the mounting base to the ceiling; rotate the back box counterclockwise to secure it to the mounting base; use the lock screw to secure the dome camera.
PAGE 24
Installation Manual | VISIX Network Camera 5) Connect the RCA analog video output to a monitor to view the camera image. Loosen the lens set screw to adjust the pan, tilt and rotation angle. 6) Adjust the focus to obtain the desired image. Fasten the lens set screw.
PAGE 25
Installation Manual | VISIX Network Camera In-‐Ceiling Mounting Steps: 4) Secure the mounting base to the in-‐ceiling mounting base with screws.
PAGE 26
Installation Manual | VISIX Network Camera Figure 4-‐11 Installing 7) It is strongly recommended that you use a safety rope to secure the in-‐ceiling mounting base to the roof. Safety Rope Figure 4-‐12 Safety Rope 8) Fasten the lock screws to secure the dome camera.
PAGE 27
Installation Manual | VISIX Network Camera 9) Remove the bubble and connect the RCA analog video output with a monitor to view the camera image. Loosen the lens set screw and pan, tilt or rotate the lens to achieve a satisfactory surveillance angle. Adjust the lens focus to obtain the desired image. Fasten the lens set screw.
PAGE 28
Installation Manual | VISIX Network Camera 4.
PAGE 29
Installation Manual | VISIX Network Camera 9 10 Figure 4-‐18 Overview (3) Figure 4-‐19 Overview (4) Table 1-‐6 Description of Overview (2~3) No. Description No.
PAGE 30
Installation Manual | VISIX Network Camera Name/Label LAN（PoE） 10M/100M Self-‐adaptive Ethernet Port(PoE Supported) AUDIO OUT/IN Audio Out/In CVBS，GND Auxiliary video output 1A，1B Alarm Out D+，D-‐ RS-‐485 Interface IN，GND DC12V NOTE: Description ALARM IN Power Supply Interface（12 VDC ） Press and hold RESET for 10s when the camera is powe
PAGE 31
Installation Manual | VISIX Network Camera Side Outlet Figure 4-‐21 Side Outlet 2) Attach the adapter plate to the ceiling with the supplied screws.
PAGE 32
Installation Manual | VISIX Network Camera 4) Adjust the surveillance angle according to the figure below. Panning angle [0~80°], tilting angle [0~355°], and azimuth angle of the lens [0~355°]. 0~80° 0~355° 0~355° Figure 4-‐24 3-‐axis Adjustment 5) Adjust the focus and zoom. a. Connect the VIDEO OUT interface of the camera to the debugging monitor.
PAGE 33
Installation Manual | VISIX Network Camera To digitally adjust the zoom and focus, visiting the device’s web interface and adjust these settings from the PTZ control interface. NOTE: Figure 4-‐26 Zoom and Focus Adjustment of Electronic Lens 6) Attach the black liner to the dome drive.
PAGE 34
Installation Manual | VISIX Network Camera 5 Mini-‐Dome Camera Installation 5.1 Type I Mini-‐Dome Camera APPLICABLE CAMERA MODELS This section applies to the following camera models: ! VSX-‐2MP-‐MVD4 ! VSX-‐2MP-‐MVD28 ! VSX-‐2MP-‐MVD40 CAMERA DESCRIPTION Figure 5-‐1 Overview Table 1-‐8 Physical Description No.
PAGE 35
Installation Manual | VISIX Network Camera NOTE: Press and hold the RESET button for 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.
PAGE 36
Installation Manual | VISIX Network Camera Figure 5-‐4 Attach the Camera 4) View the video camera image over the network. 5) Loosen the lens set screws.
PAGE 37
Installation Manual | VISIX Network Camera Figure 5-‐6 Adjust Panning Position Figure 5-‐7 Adjust Tilting Position NOTE: As the lens of camera has already been factory adjusted to the best image, adjust only the panning position and tilting position to achieve the desired surveillance angle.
PAGE 38
Installation Manual | VISIX Network Camera Figure 5-‐8 Install the Cover 5.
PAGE 39
Installation Manual | VISIX Network Camera Figure 5-‐10 Overview (2) Table 1-‐9 Physical Description No.
PAGE 40
Installation Manual | VISIX Network Camera Steps: 1) Press the WPS button on the router. 2) Press the WPS button (about 2s) on the camera within 120s of enabling the WPS on the router to join the wireless network. ! The WPS button works as a reset button only when you press it when the camera is powering on.
PAGE 41
Installation Manual | VISIX Network Camera Drill Template A 1 1 Hole A :for cables routed through the wall Screw hole1 :for Mounting Base FRONT Code:194101278 Figure 5-‐12 Type II Drill Template/Adapter Plate 2) Loosen the set screw on the front cover to disassemble the camera with the supplied Allen key.
PAGE 42
Installation Manual | VISIX Network Camera Adapter Plate Side Outlet Figure 5-‐14 Attach the Adapter Plate NOTE: If the supplied drill template is type II drill template, you can skip step 3 and go straight to step 4. 4) Attach the dome drive with the supplied PM4x8 screws.
PAGE 43
Installation Manual | VISIX Network Camera Figure 5-‐16 Remove the Removable Part 6) View the image via the web browser. 7) Slightly loosen the hex screw beside the WPS/RESET button to adjust the surveillance angle. 8) Use the supplied adjusting tool to adjust the pan [±30°], tilt [0~80°], and rotation direction [0~360°].
PAGE 44
Installation Manual | VISIX Network Camera Pendant Mounting (3xLOGIC Part #: VX-‐PM-‐MD) Steps: 1) Install the bracket to the ceiling with the supplied screws in the ceiling bracket package. NOTE: The matched ceiling bracket model is DS-‐1271ZJ-‐120, and you need to purchases it separately if ceiling bracket mounting is adopted.
PAGE 45
Installation Manual | VISIX Network Camera 4) Align the front cover to the dome drive and tighten the set screws on the front cover to complete the installation.
PAGE 46
Installation Manual | VISIX Network Camera Figure 5-‐23 Attach the Adapter Plate 2) Attach the dome drive to the wall bracket with the supplied screws. Figure 5-‐24 Attach the Camera 3) Align the front cover to the dome drive and tighten the set screws on the front cover to complete the installation.
PAGE 47
Installation Manual | VISIX Network Camera Figure 5-‐25 Install the Front Cover Install the Micro SD Card This series of camera supports local storage, please refer to the following steps to install the Micro SD card. Steps: 1) Remove the front cover by loosening the set screws on it.
PAGE 48
Installation Manual | VISIX Network Camera Mirco SD Card Figure 5-‐27 Install and Uninstall Micro SD Card CAMERA DESCRIPTION OF TYPE II MINI-‐DOME CAMERA (TYPE B) Figure 5-‐28 Overview Table 1-‐10 Physical Description No. Description 1 Cover 2 Lens 3 Power LED indicator, It turns solid red when power is connected.
PAGE 49
Installation Manual | VISIX Network Camera NOTE: Press and hold RESET for 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.
PAGE 50
Installation Manual | VISIX Network Camera Figure 5-‐31 Install Micro SD Card 3) Attach the camera to the ceiling with the supplied screws. Figure 5-‐32 Attach the Camera 4) View the video camera image over the network. 5) Loosen the lens set screws.
PAGE 51
Installation Manual | VISIX Network Camera 6) Insert the hex key into the hole marked in the picture and rotate the hex key to adjust the panning position and tilting position until the desired surveillance angle is achieved. Tighten the set screws to lock the angle.
PAGE 52
Installation Manual | VISIX Network Camera Figure 5-‐36 Install the Back Box 10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.
PAGE 53
Installation Manual | VISIX Network Camera 6 Outdoor Dome Camera Installation 6.1 Type I Outdoor Dome Camera APPLICABLE CAMERA MODELS This section applies to the following camera models: ! VSX-‐3MP-‐ODIR28 ! VX-‐3P28-‐OD-‐I CAMERA DESCRIPTION There are two types of camera appearance for this series of camera according to the different models.
PAGE 54
Installation Manual | VISIX Network Camera NOTE: Press and hold RESET for 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.
PAGE 55
Installation Manual | VISIX Network Camera 3) Attach the mounting base on the ceiling with screws. Figure 6-‐4 Attach the Mounting Base NOTE: If required, you can route cables through the side opening on the side of the mounting base.
PAGE 56
Installation Manual | VISIX Network Camera NOTE: As the lens has already been factory adjusted to the best image, you just need to adjust the panning position and tilting position to get the desired surveillance angle. 6) Reinstall the bubble and tighten the screws.
PAGE 57
Installation Manual | VISIX Network Camera Figure 6-‐9 Insert the Micro SD Card 4) Re-‐install the bubble and tighten the lock screws. Figure 6-‐10 Install the Bubble 6.
PAGE 58
Installation Manual | VISIX Network Camera 1 2 3 Figure 6-‐11 Overview (1) Figure 6-‐12 Overview (2) 10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.
PAGE 59
Installation Manual | VISIX Network Camera Table 1-‐12 Description of Overview (1~2) No. Description No.
PAGE 60
Installation Manual | VISIX Network Camera INSTALLATION Steps: 1) Drill the screw holes and the cable hole according to the supplied drill template.
PAGE 61
Installation Manual | VISIX Network Camera Dome Drive Figure 6-‐15 Install the Dome Drive 5) Adjust the surveillance angle. a. Loosen the lock screw besides the lens. b. Hold the plastic plate and rotate the camera to adjust the panning angle [0~350°]. c. Push the lens forward and backward to adjust the tilting angle [0~80°]. d.
PAGE 62
Installation Manual | VISIX Network Camera d. Adjust the No.1 Focus Lever (F~N) to obtain the desired image on the monitor. e. Set the iris type as MANUAL if the environment has a stable level of illumination. Set the iris type to AUTO if the environment has varying illumination levels.
PAGE 63
Installation Manual | VISIX Network Camera 6.3 Type III Outdoor Dome Camera APPLICABLE CAMERA MODELS This section applies to the following camera models: ! VSX-‐OD2-‐IRFH CAMERA DESCRIPTION 6 7 8 1 2 3 4 5 Figure 6-‐19 Overview Table 1-‐14 Physical Description No.
PAGE 64
Installation Manual | VISIX Network Camera AVAILABLE MOUNTS ! OD Wall Mount (3xLOGIC Product #: VX-‐WM-‐OD2) ! OD Wall Mount w/ Junction Box (3xLOGIC Product #: VX-‐WMJ-‐OD2) ! OD Pendant Mount (3xLOGIC Product #: VX-‐PM-‐OD2) ! Universal Corner Mount (3xLOGIC Product #: VX-‐CM) ! Universal Pole Mount ( 3xLOGIC Product #: VX-‐POLE) INSTALLATION
PAGE 65
Installation Manual | VISIX Network Camera Figure 6-‐21 Disassembling 4) Install the dome drive to the back box and pull the cables through the cable outlet on the bottom of the back box.
PAGE 66
Installation Manual | VISIX Network Camera Outlet Figure 6-‐23 Side Cable Routing 5) After connecting the network cable and power cable, view the camera image over the network.
PAGE 67
Installation Manual | VISIX Network Camera In-‐Ceiling Mounting Steps: 1) Drill the screw holes and the cable hole on the ceiling according to the supplied drill template.
PAGE 68
Installation Manual | VISIX Network Camera Toggle Bolt Figure 6-‐25 Dome Drive Installing 6) Fasten the toggle bolt and the toggle will automatically secure the dome drive to the ceiling. Ceiling Figure 6-‐26 Fasten Toggle Bolt 7) Connecting the network cable and power cable. 8) View the camera image over the network.
PAGE 69
Installation Manual | VISIX Network Camera Pan Tilt Lock Screw Rotate Figure 6-‐27 Angle Adjusting 11) Reinstall the black liner and dome drive to finish the installation. Figure 6-‐28 Complete the Installation 10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.
PAGE 70
Installation Manual | VISIX Network Camera Wall Mounting Steps: 1) Drill the screw holes and the cable hole on the wall according to the supplied drill template.
PAGE 71
Installation Manual | VISIX Network Camera Figure 6-‐31 Disassembling 4) Install the dome drive to the back box and pull the cables through the side outlet on the bottom of the back box.
PAGE 72
Installation Manual | VISIX Network Camera 8) Fasten the lock screws. Pan Tilt Lock Screw Rotate Figure 6-‐33 Angle Adjusting 9) Reinstall the black liner and bubble to finish the installation. Figure 6-‐34 Complete the Installation 10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.
PAGE 73
Installation Manual | VISIX Network Camera 7 Bullet Camera Installation 7.1 Type I Bullet Camera APPLICABLE CAMERA MODELS This section applies to the following camera models: ! VSX-‐2MP-‐BIR-‐RF ! VSX-‐3MP-‐BIR-‐RF CAMERA DESCRIPTION Two types of camera rear panel are shown in Figure 4-‐7 and Figure 4-‐8.
PAGE 74
Installation Manual | VISIX Network Camera Table 1-‐19 Physical Description No.
PAGE 75
Installation Manual | VISIX Network Camera Table 1-‐20 Attach the Camera 3) View the camera image over the network. 4) Loosen the screws on the bracket slightly. NOTE: Please loosen the screws slightly until you can adjust the camera and do not remove the screws from the bracket.
PAGE 76
Installation Manual | VISIX Network Camera Table 1-‐21 Remove the Sun Shield 7) Rotate to remove the front cover from camera and adjust the lens to get a clear image. Adjust the Front Lens Cover Table 1-‐22 Adjust the Lens 8) Attach the lens; reinstall the front cover and the sun shield to finish the installation.
PAGE 77
Installation Manual | VISIX Network Camera 7.2 Type II Bullet Camera APPLICABLE CAMERA MODELS This section applies to the following camera models: ! VSX-‐1.3MP-‐MBIR ! VX-‐3P28-‐MD-‐I ! VX-‐3P4-‐MD-‐I CAMERA DESCRIPTION 1 2 3 4 5 6 Figure 7-‐6 Bullet Camera Overview Table 1-‐23 Description No.
PAGE 78
Installation Manual | VISIX Network Camera AVAILABLE MOUNTS ! Universal Corner Mount (3xLOGIC Product #: VX-‐CM) ! Universal Pole Mount ( 3xLOGIC Product #: VX-‐POLE) These cameras have a built-‐in mount for wall and ceiling mount applications. INSTALLATION Steps: 1) Attach the drill template on the wall.
PAGE 79
Installation Manual | VISIX Network Camera c. Adjust the tilting angle [0~90°] of the camera. d. Rotate 0~360° to adjust azimuth angle of the image. e. Tighten the adjustable nut to complete the installation. T Direction R Direction P Direction Adjustable Nut Table 1-‐24 3-‐axis Adjustment 7.
PAGE 80
Installation Manual | VISIX Network Camera Table 1-‐25 Overview NOTE: No.
PAGE 81
Installation Manual | VISIX Network Camera Lock Screw Figure 7-‐10 Disassemble the Camera 4) Insert the Micro SD card into the Micro SD card slot. 5) Rotate the front cover clockwise to install the sun shield according to the arrow direction as shown in Figure 7-‐11(right).
PAGE 82
Installation Manual | VISIX Network Camera 1 Rotating Label Figure 7-‐12 Assemble the Camera NOTE: For water-‐proofing, please align the rotating label on the front cover with that on the camera when you rotate the front cover clockwise. Refer to Figure 7-‐12 , above (right).
PAGE 83
Installation Manual | VISIX Network Camera Figure 7-‐14 Secure the Camera View Angle Adjusting Purpose: 3-‐axis (pan/tilt/rotation) adjusting allows adjustment for optimum camera rotation and placement. Pan Adjustment Steps: 1) Loosen the lock screw-‐1. 2) Adjust the panning position of the camera.
PAGE 84
Installation Manual | VISIX Network Camera Panning 1 Rotation 2 3 Tilting Figure 7-‐15 Lens Adjustment Zoom and Focus Adjusting Purpose: You can use the zoom lever and focus lever to adjust the zoom value and focus value. Steps: 1) Disassemble the camera. 2) View the camera image using the monitor.
PAGE 85
Installation Manual | VISIX Network Camera 7.4 Type IV Bullet Camera APPLICABLE CAMERA MODELS This section applies to the following camera models: ! VX-‐2M-‐B-‐RIA ! VX-‐3M-‐B-‐RIAWD CAMERA DESCRIPTION The overview of the network bullet camera is shown below. Please note the amount of cables included in the harness will vary between models.
PAGE 86
Installation Manual | VISIX Network Camera AVAILABLE MOUNTS ! Universal Corner Mount (3xLOGIC Product #: VX-‐CM) ! Universal Pole Mount ( 3xLOGIC Product #: VX-‐POLE) These cameras have a built-‐in mount for wall and ceiling mount applications. INSTALLATION Steps: 1) Drill four screw holes in the wall according to the No.
PAGE 87
Installation Manual | VISIX Network Camera 4) Route the cables of the camera. ! Route the cables through the junction box and the cable hole if there is a cable hole drilled on the ceiling.
PAGE 88
Installation Manual | VISIX Network Camera ! Please loosen the screws slightly until you can adjust the camera. Do not completely remove the screws from the bracket.
PAGE 89
Installation Manual | VISIX Network Camera 8 Cube Camera Installation 8.1 Type I Cube Camera APPLICABLE CAMERA MODELS This section applies to the following camera models: ! VSX-‐1.3MP-‐PIR1 CAMERA DESCRIPTION The overview of the network cube camera is shown below.
PAGE 90
Installation Manual | VISIX Network Camera No. Description 2 Photosensitive Resistance 3 PIR sensor 4 Microphone 5 Lens 6 3-‐axis Adjustment Bracket 7 Alarm Indicator: Indicator goes solid red (camera armed) or solid blue (camera unarmed).
PAGE 91
Installation Manual | VISIX Network Camera Figure 8-‐3 Remote Control Table 1-‐29 Remote Control Button Description Button Name Description Status Indicating the status of the remote control; when you press any button, the indicator flashes Indicator red. Press the button to arm the camera.
PAGE 92
Installation Manual | VISIX Network Camera 3) Attach the camera to the ceiling with the supplied expansion screws. Figure 8-‐5 Attach the Camera to Ceiling 4) Connect the coresponding power cable and the network cable through the drilled cable hole. Or pull the cable through the side outlet of the camera.
PAGE 93
Installation Manual | VISIX Network Camera Lock Nut 1 Pan Tilt Lock Nut 2 Rotation Figure 8-‐7 Adjust the Camera 10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.
PAGE 94
Installation Manual | VISIX Network Camera 9 Mount Schematics 9.1 D2 Ceiling Flush Mount (VX-‐FM-‐D2) 10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.
PAGE 95
Installation Manual | VISIX Network Camera 9.2 D2 Wall Mount Adapter(VX-‐WM-‐D2) 10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.
PAGE 96
Installation Manual | VISIX Network Camera 9.3 D2 Wall Mount with Junction Box (VX-‐WMJ-‐D2) 10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.
PAGE 97
Installation Manual | VISIX Network Camera 9.4 MD Pendant Mount (VX-‐WM-‐MD) 10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.
PAGE 98
Installation Manual | VISIX Network Camera 9.5 MD Wall Mount (VX-‐WM-‐MD) 10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.
PAGE 99
Installation Manual | VISIX Network Camera 9.6 OD2 Pendant Mount (VX-‐PM-‐OD2) 10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.
PAGE 100
Installation Manual | VISIX Network Camera 9.7 OD2 Wall Mount (VX-‐WM-‐OD2) 10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.
PAGE 101
Installation Manual | VISIX Network Camera 9.8 OD2 Wall Mount with Junction Box (VX-‐WMJ-‐OD2) 10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.
PAGE 102
Installation Manual | VISIX Network Camera 9.9 Universal Corner Mount (VX-‐CM) 10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.
PAGE 103
Installation Manual | VISIX Network Camera 9.10 Universal Pole Mount (VX-‐POLE) 10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.