User Manual
Table Of Contents
- 1. Getting started
- 2. Introduction
- 3. Preparation
- 4. About the terminal
- 5. Mounting and installing the terminal
- 6. Connecting to the terminal
- 7. Managing the terminal
- 8. Configuring the terminal
- 9. Configuring the traffic interfaces
- 10. Cross Connections
- Embedded cross connect switch
- The Cross Connections application
- The Cross Connections system requirements
- Installing the Cross Connections application
- Opening the Cross Connections application
- The Cross Connections page
- Setting the terminal's address
- Management and user ethernet capacity
- Setting card types
- Getting cross connection configuration from the terminals
- Creating cross connections
- Sending cross connection configuration to the terminals
- Saving cross connection configurations
- Using existing cross connection configurations
- Printing the cross connection configuration
- Deleting cross connections
- Configuring the traffic cross connections
- Cross connection example
- Symmetrical Connection Wizard
- 11. Protected terminals
- 12. In-service commissioning
- What you will need
- Checking the antenna polarization
- Visually aligning antennas
- Accurately aligning the antennas
- Synchronizing the terminals
- Checking performance
- Checking the receive input level
- Checking the fade margin
- Checking long-term BER
- Bit Error Rate tests
- Additional tests
- Checking the link performance
- Viewing a summary of the link performance
- What you will need
- 13. Maintenance
- 14. Troubleshooting
- 15. Interface connections
- 16. Alarm types and sources
- 17. Country specific settings
- 18. Specifications
- Ethernet interface
- QJET Quad E1 / T1 interface
- Q4EM Quad 4 wire E&M interface
- DFXO Dual foreign exchange office interface
- DFXS Dual foreign exchange subscriber interface
- QV24 Quad V.24 asynchronous data interface
- HSS Single high speed synchronous data interface
- External alarm interfaces
- Auxiliary interfaces
- AC Power supply
- DC Power supply
- Power consumption
- MHSB protection
- Ethernet interface
- 19. Product end of life
- 20. Abbreviations
- 21. Acknowledgments and licensing
- 22. Commissioning Forms
- 23. Index
Configuring the traffic interfaces | 102
3. Set the DFXO Input Level and the Output Level required:
Signal Direction Level adjustment range Default setting
Input Level (L
i
) -10.0 dBr to +1.0 dBr in 0.5 dB steps -4.0 dBr
Output Level (L
o
) -10.0 dBr to +1.0 dBr in 0.5 dB steps -1.0 dBr
In the example shown below, the PSTN exchange line card is connected to a DFXO card.
The levels are set based on the system using a 0 dBr transmission reference point.
Output level
-6.0 dBr
Input level
+1.0 dBr
Output level
-1.0 dBr
Input level
-4.0 dBr
Transmission Reference point
0 dBr
DFXO Input Level setting
The exchange line card has a nominal output level of -6 dBr. To achieve a digital reference point
transmit level of -2.0 dBm0, the DFXO input level is set to -4.0 dBr (effective T pad gain of 4.0 dB).
The deliberate 2 dB of loss between the exchange line card and the DFXO provides a 2 dB of
overall circuit loss between the DFXO and the DFXS.
DFXO Output Level setting
The exchange line card has a nominal input level of +1.0 dBr. With a transmission reference point
received level of -2.0 dBm0, the DFXO output level is set to -1.0 dBr (effective R pad loss of 1.0
dB).
The deliberate 2 dB of loss between the exchange line card and the DFXO provides a 2 dB of
overall circuit loss between the DFXS and the DFXO.
4. Click Apply to apply changes or Reset to restore the previous configuration.