® Threat Analysis Reporter QUICK START GUIDE Model: TAR HL-005-004, SL-004-004, MSA-004-004 Release: 1.2.00 / Updated: 09.19.
8e6 Threat Analysis Reporter Quick Start Guide © 2008 8e6 Technologies. All rights reserved. This document may not, in whole or in part, be copied, photocopied, reproduced, translated, or reduced to any electronic medium or machine readable form without prior written consent from 8e6 Technologies. Every effort has been made to ensure the accuracy of this document.
Contents Threat Analysis Reporter Introduction. ...................................................1 About this Document..................................................................................................................... 2 Conventions Used in this Document............................................................................................ 2 Service Information...................................................................................3 Preliminary Setup Procedures...........
iv 8e6 Threat Analysis Reporter Quick Start Guide
Threat Analysis Reporter Introduction Thank you for choosing to evaluate the 8e6 Technologies Threat Analysis Reporter. This product addresses user-generated Web threats such as excessive use of bandwidth and inappropriate Internet usage, and provides network administrators tools to monitor such threats so management can enforce corporate Internet usage policies.
About this Document This document is divided into the following sections: • Introduction - This section is comprised of an overview of the Threat Analysis Reporter product and how to use this document • Service Information - This section provides 8e6 Technologies contact information • Preliminary Setup Procedures - This section includes instructions on how to physically set up the Threat Analysis Reporter unit in your network environment • Install the Server - This section explains how to configure t
Service Information The user should not attempt any maintenance or service on the unit beyond the procedures outlined in this document. Any initial hardware setup problem that cannot be resolved at your internal organization should be referred to an 8e6 Technologies solutions engineer or technical support representative. 8e6 Corporate Headquarters (USA) Local Domestic US International : : : 714.282.6111 1.888.786.7999 +1.714.282.
Preliminary Setup Procedures Unpack the Unit from the Carton Inspect the packaging container for evidence of mishandling during transit. If the packaging container is damaged, photograph it for reference. Carefully unpack the unit from the carton and verify that all accessories are included. Save all packing materials in the event that the unit needs to be returned to 8e6 Technologies.
Select a Site for the Server The server operates reliably within normal office environmental limits. Select a site that meets the following criteria: • Clean and relatively free of excess dust. • Well-ventilated and away from sources of heat, with the ventilating openings on the server kept free of obstructions. • Away from sources of vibration or physical shock.
Rack Mount the Server Rack Setup Precautions Warning: Before rack mounting the server, the physical environment should be set up to safely accommodate the server. Be sure that: • The weight of all units in the rack is evenly distributed. Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading. • The rack will not tip over when the server is mounted, even when the unit is fully extended from the rack.
Rack Mount Instructions for HL Servers Rack Setup Suggestions • • Determine the placement of each component in the rack before you install the rails. Install the heaviest server components on the bottom of the rack first, and then work up. Identify the Sections of the Rack Rails You should have received two rack rail assemblies with the 8e6 server unit.
Locking Tabs: Both chassis rails have a locking tab, which serves two functions. The first is to lock the server into place when installed and pushed fully into the rack, which is its normal position. Secondly, these tabs also lock the server in place when fully extended from the rack. This prevents the server from coming completely out of the rack when you pull it out for servicing.
Install the Server into the Rack You should now have rails attached to both the chassis and the rack unit. The next step is to install the server chassis into the rack. Do this by lining up the rear of the chassis rails with the front of the rack rails. Slide the chassis rails into the rack rails, keeping the pressure even on both sides (you may have to depress the locking tabs when inserting). When the server has been pushed completely into the rack, you should hear the locking tabs “click.
Install the Server into a Telco Rack If you are installing the 8e6 server unit into a Telco type rack, use two L-shaped brackets on either side of the chassis (four total). First, determine how far follow the server will extend out the front of the rack. A larger chassis should be positioned to balance the weight between front and back. If a bezel is included on your server, remove it.
Rack Mount Instructions for SL Servers Rack Setup Suggestions • • Determine the placement of each component in the rack before you install the rails. Install the heaviest server components on the bottom of the rack first, and then work up. Install the Inner Slides 1. Locate the right inner slide, (the slide that will be used on the right side of chassis when facing the front panel of the chassis). 2.
Install the Slide Assemblies to the Rack 1. After you have installed the short and long brackets to the outer slides, you are ready to install the whole slide assemblies (outer slides with short and long brackets attached) to the rack. (See the previous page.) 2.
Install the Chassis into the Rack 1. Push the inner slides, which are attached to the chassis, into the grooves of the outer slide assemblies that are installed in the rack as shown below: 2.
Rack Mount Instructions for MSA Servers Optional: Install the Chassis Rails NOTE: If your chassis does not come with chassis rails, please follow the procedure listed on the last page of this sub-section to install the unit directly into the rack. CAUTION: Please make sure that the chassis covers and chassis rails are installed on the chassis before you install the chassis into the rack.
3. Locate the three holes on each side of the chassis and locate the three corresponding holes on each of the inner rail. 4. Attach an inner rail to each side of the chassis and secure the inner rail to the chassis by inserting three Type G screws through the holes on each side of the chassis and the inner rail. (See the diagram below for a description of the Type G screw.) 5. Repeat the above steps to install the other rail on the chassis.
Optional: Install the Traditional UP Racks After you have installed the inner rails on the chassis, you are ready to install the outer rails of rail assemblies to the rack. NOTE: The rails are designed to fit in the racks with the depth of 28” to 33”. • • Determine the placement of each component in the rack before you install the rails. Install the heaviest server components on the bottom of the rack first, and then work up. 1. In the package, locate a pair of front (short) and rear (long) brackets.
7. Slide the chassis into the rack as shown below. NOTE: The chassis may not slide into the rack smoothly or easily when installed the first time. Some adjustment to the slide assemblies might be needed for easy installation. 8. You will need to release the safety taps on both sides of the chassis in order to completely remove the chassis out of the rack.
Optional: Install the Open Racks After you have installed the inner rails on the chassis, you are ready to install the outer rails of rail assemblies to the rack. NOTE: The rails are designed to fit in the racks with the depth of 28” to 33”. • • Determine the placement of each component in the rack before you install the rails. Install the heaviest server components on the bottom of the rack first, and then work up. 1. In the package, locate a pair of front (short) and rear (long) brackets.
3. Attach the front (short) bracket to the front end of the rack, and secure it to the rack with two Type H screws and Type I washers as shown below. (See the previous page for descriptions of Type H and Type I hardware components.) 4. Attach the rear (long) bracket to the rear end of the rack, and secure it to the rack with two Type H screws and Type I washers as shown below. Repeat the same steps to install the other outer rail to the other side of rack.
5. Measure the depth of your rack and adjust the length of the rails accordingly. Then, secure the rails to the chassis with Type G screws. 6. Slide the inner rails which are attached to the chassis into the outer rails on the rack.
Install the Chassis into the Rack CAUTION: Before installing the chassis into the rack: • • • • • • Make sure that the rack is securely anchored onto an unmovable surface or structure before installing the chassis into the rack. Unplug power cord(s) of the rack before installing the chassis into the rack. Make sure that the system is adequately supported. Make sure that all the components are securely fastened to the chassis to prevent components falling off from the chassis.
Install the SL or HL Server Bezel After rack mounting an SL or HL server, the bezel should be installed on the front end of the chassis. NOTE: This portion of the installation process requires you to unpack the bezel. The bezel has been packaged separately from the unit to prevent damage during shipping. A. Hold the bezel upright and facing towards you (Fig. 1). Fig. 1 - Front of bezel B. Note that each end of the bezel contains two raised bumps (Fig. 2). Fig. 2 - Bumps on right end of bezel Fig.
Check the Power Supply This server is equipped with a universal power supply that handles 100-240 V, 50/60 Hz. A standard power cord interface (IEC 950) facilitates power plugs that are suitable for most European, North American, and Pacific Rim countries. Power Supply Precautions Warning: • Use a regulating uninterruptible power supply (UPS) to protect the server from power surges, voltage spikes and to keep the server operating in case of a power failure.
General Safety Information Server Operation and Maintenance Precautions Warning: Observe the following safety precautions during server operation and maintenance: WARNING: If the server is used in a manner not specified by the manufacturer, the protection provided by the server may be impaired. WARNING: 8e6 Technologies is not responsible for regulatory compliance of any server that has been modified.
• Do not expose the server to rain or use near water. If liquids of any kind should leak into the chassis, power down the server, unplug it, and contact 8e6 Technologies technical support. • Disconnect power from the server before cleaning the unit. Do not use liquid or aerosol cleaners. AC Power Cord and Cable Precautions Warning: • The AC power cord for the server must be plugged into a grounded, power outlet.
Motherboard Battery Precautions Caution: The battery on the motherboard should not be replaced without following instructions provided by the manufacturer. Only qualified service personnel should replace batteries. The battery contains energy and, as with all batteries, a malfunction can cause heat, smoke, or fire, release toxic materials, or cause burns. Do not disassemble, puncture, drop, crush, bend, deform, submerge or modify the battery. Do not incinerate or expose to heat above 140°F (60°C).
Install the Server Step 1: Initial Setup Procedures This step requires you to link the workstation to the Threat Analysis Reporter. You have the option of using the text-based Quick Start setup procedures described in Step 1A, or, if you have an SL or HL unit, the LCD panel setup procedures described in Step 1B.
Step 1A: Quick Start Setup Procedures Link the Workstation to the Threat Analysis Reporter Monitor and Keyboard Setup A. Connect the PC monitor and keyboard cables to the rear of the chassis (see Fig. 1 for an SL or MSA unit, and Fig. 2 for an HL unit). B. Turn on the PC monitor. C. Power on the Threat Analysis Reporter by dropping down the face plate and pressing the large button at the right of the front panel (see Fig. 3 for an SL unit, Fig. 4 for an MSA unit, and Fig. 5 for an HL unit).
Fig. 3 - Diagram of SL chassis front panel, power button at far right Fig. 4 - Diagram of MSA chassis front panel, power button at far right Fig. 5 - Diagram of HL chassis front panel, power button at far right Once the Threat Analysis Reporter is powered up, proceed to the instructions for HyperTerminal Setup Procedures.
HyperTerminal Setup Procedures If using a serial console, follow these procedures to create a HyperTerminal session on the serial console. A. Launch HyperTerminal by going to Start > Programs > Accessories > Communications > HyperTerminal: B.
C. At the Connect using field, select the COM port assigned to the serial port on the laptop (probably “COM1”), and then click OK to open the Properties dialog box, displaying the Port Settings tab: D. Specify the following session settings: • • • • • Bits per second: 9600 Data bits: 8 Parity: None Stop bits: 1 Flow control: Hardware E.
F. In the HyperTerminal session window, go to File > Properties to open the Properties dialog box, displaying the Connect To and Settings tabs: G. Click the Settings tab, and at the Emulation menu select “VT100”. H. Click OK to close the dialog box, and to go to the login screen. NOTE: If using a HyperTerminal session, the login screen will display with black text on a white background.
Quick Start menu instructions For these Quick Start setup procedures, you will need your network administrator to provide you the LAN 1 and LAN 2 IP address and subnet mask, gateway IP address, DNS server IP address(es), host name of the server, and IP address for the Web interface (if using a NAT device). Login screen, password prompts The login screen displays after powering on the Threat Analysis Reporter unit using a monitor and keyboard, or after creating a HyperTerminal session.
E. At the Press the number of your selection prompt, press 2 to display the Administrator Password Entry screen: F. At the Enter the administrator password prompt, re-enter your password: #s3tup#r3k G. Press Enter to display the Administration menu where you can begin the Quick Start setup process using the configuration screens: H. At the Press the number of your selection prompt, press 2 to select the “Quick Start setup” process. This process takes you to the Configure Network Interface screen.
Configure Network Interface screen A. At the Enter interface lan1 IP address field, enter the IP address for the LAN 1 interface, and then press Enter to go to the next screen. B. At the Enter interface lan1 netmask field, enter the subnet mask for the LAN 1 interface using the dotted decimals notation format. Press Enter to display the confirmation prompt.
C. Press Y for “Yes” to confirm and save your entries for the LAN1 interface, and to go to the next screen. D. At the Enter interface lan2 IP address field, enter the IP address for the LAN 2 interface, and then press Enter to go to the next screen. E. At the Enter interface lan2 netmask field, using the dotted decimals notation format, enter the subnet mask for the LAN 2 interface. Press Enter to display the confirmation prompt. F.
Configure default gateway screen A. At the Enter default gateway IP field, enter the IP address for the default gateway. Press Enter to display the confirmation prompt. B. Press Y for “Yes” to confirm and save your entry for the gateway IP address, and to go to the Configure Domain Name Servers screen. Configure Domain Name Servers screen A. At the Enter first DNS server IP field, enter the IP address for the primary Domain Name Server. Press Enter to go to the next screen.
B. At the Enter (optional) second DNS server IP field, if you have a secondary Domain Name Server you wish to use, enter the IP address for that server. Press Enter to display the confirmation prompt. C. Press Y for “Yes” to confirm and save your entries for the domain name servers, and to go to the Configure Host Name screen. Configure Host Name screen A. At the Enter host name field, enter the host name of the server. Press Enter to display the confirmation prompt.
B. Press Y for “Yes” to confirm and save your entry for the host name, and to go to the Time zone regional configuration screen. Time zone regional configuration screen A. Use the up and down arrows in your keyboard to select your region. After selecting your locality, press Y for “Yes” to confirm and save your regional selection, and to go to the next screen: B. Use the up and down arrows in your keyboard to select your region.
Configure Wizard user screen A. At the Enter wizard user name field, enter the username that will be used to access the setup wizard in the Threat Analysis Reporter interface. Press Enter to display the confirmation prompt. B. Press Y for “Yes” to confirm and save your entry and to go to the next screen. C. At the Enter wizard password field, enter the password that will be used to access the setup wizard in the Threat Analysis Reporter interface.
Quick Start Setup confirmation screen Press Y for “Yes” to save all your Quick Start setup entries and to return to the Administration menu. NOTE: When saving your entries, there may be a 4-10 second delay before the Administration menu displays. Administration menu After making all entries using the Quick Start setup process, you will return to the Administration menu. Press X to return to the Quick Start menu screen.
System Status screen The System Status screen contains the following information: • • • • • • • lan1 interface for web access and R3000 communications: LAN1 IP address and netmask specified in screen 3 (Configure Network Interface), and current status (“Active” or “Inactive”) lan2 interface for bandwidth monitoring: LAN2 IP address and netmask specified in screen 4 (Configure Network Interface), and current status (“Active” or “Inactive”) Default gateway IP address specified in screen 5 (Configure default
Physically Connect the Unit to the Network After performing initial setup procedures for the Threat Analysis Reporter, the unit should be physically connected to the network. This step requires a standard CAT-5E cable to connect the unit to the network. An additional CAT-5E cable is required if the Ethernet Tap unit will be installed for bandwidth monitoring. A. Plug one end of a standard CAT-5E cable into the Threat Analysis Reporter’s LAN 1 port, the port on the left. Fig.
Step 1B: LCD Panel Setup Procedures On an SL or HL unit, the Threat Analysis Reporter can be configured using the LCD panel on front of the chassis bezel.
• • Reboot > Shutdown > • • • NOTE: Navigation tips in the 8e6 menu: Use the up / down arrow key to scroll up / down the menu Press the checkmark key to choose the current selection Press the “X” to go back to the previous screen Make a selection from the menu, and press the checkmark key to go to that screen. Current Patch Level When the Current Patch Level option is selected, “Threat Analysis Reporter” and the version number of the currently installed build displays.
Gateway When the Gateway option is selected, the Gateway screen displays with the Configure Gateway IP menu item. A. Choose Configure Gateway IP and press the checkmark key to go to the Configure Gateway IP screen. B. Use the up / down keys to increase / decrease the current value, and the left / right arrow keys to navigate across the line. C. Press the checkmark key to accept your entry and to return to the previous screen. D. Press the “X” key to return to the 8e6 menu.
C. Press the checkmark key to return to the previous screen. D. Press the “X” key to return to the 8e6 menu. Regional Setting (Time Zone, date, time) When the Regional Setting (Time Zone, date, time) option is selected, the Regional Setting (Time Zone, date, time) screen displays with the Region menu item. A. Choose Region, and use the left / right arrow keys to view the available region selections. B. After making a selection, press the checkmark key to display the Choose a Location screen. C.
Shutdown When the Shutdown option is selected, the Shutdown screen displays with two menu items. A. Choose one of two options: • • Yes, shutdown now!! - This selection shuts down the Threat Analysis Reporter. No, cancel shutdown - This selection returns you to the previous screen. B. Press the “X” key to return to the 8e6 menu.
LCD Controls When the LCD Controls option is selected, the LCD Controls screen displays with the following menu items: Contrast, On Brightness, Off Brightness. A. Choose one of the menu selections and press the checkmark key to go to that screen: • Contrast - In the Contrast screen, use the left / right arrow keys to decrease / increase the text and screen contrast.
Step 2: Wizard Setup Procedures For this step, you will need your network administrator to provide you the following information: • • • IP range and netmask of machines on the network the Threat Analysis Reporter server will be monitoring R3000 IP address, and port number to be used between the R3000 and Threat Analysis Reporter 8e6 Enterprise Reporter server IP address and server name, if an ER unit is connected to the R3000 Access the Threat Analysis Reporter Administrator Console A.
D. After reading the End User License Agreement, you have the option to do either of the following: • Click No to close both the EULA Agreement dialog box and the Threat Analysis Reporter interface. You will not be able to enable the Threat Analysis Reporter for use in your environment. • Click Yes to close the EULA Agreement dialog box and to open the Login dialog box: Proceed to the next sub-section: Log in to the Threat Analysis Reporter Wizard. Log in to the Threat Analysis Reporter Wizard A.
Wizard Step 1: Register administrator Step 1 is performed in the left side of the first screen of the wizard: A. Enter the username the global administrator will use when logging into the Threat Analysis Reporter Administrator console. The global administrator has the highest level of permissions in the Threat Analysis Reporter interface. B. Enter the password to be used with that username, and enter the same password again in the confirm password field. C.
D. Click the [+] Add tab below to open the IP Range Information dialog box: E. Enter the Bandwidth IP address range for the bandwidth the Threat Analysis Reporter will monitor. F. Enter the Bandwidth Netmask for the bandwidth IP range to be monitored, using the dotted decimals notation format. G.
To modify an IP address range, double-click the entry in the list box to highlight it and to display the [-] Remove tab to the left of the [+] Add tab: 54 • To modify the entries made for the IP address range, click the [+] Add tab to reopen the IP Range Information dialog box and edit information, as necessary. Click OK to close the dialog box and to display the modified information in the list box. • To remove the entry for the IP address range from the list box, click the [-] Remove tab.
Wizard Step 2: Register R3000 & ER Step 2 is performed in the right side of the first screen of the wizard. R3000: Specify information for the R3000 to be used with the Threat Analysis Reporter: A. Click the [+] Add tab above the R3000 list box to open the R3000 Information dialog box: B. Enter the IP address of the R3000 server to be used with the Threat Analysis Reporter. In our example, this is: 200.100.160.74, which is the LAN 2 IP address of the R3000 server. C.
E. Click OK to close the dialog box and to display your entries in the list box: NOTE: Additional R3000 servers can be included by clicking the [+] Add tab again and making the entries described in steps A through E above.
• To modify the IP address and Server Name for the R3000 server, click the [+] Add tab to re-open the R3000 Information dialog box, and edit information as necessary. Click OK to close the dialog box and to display the modified information in the list box. • To designate an R3000 as the Source R3000 server, click the entry for the R3000 server in the list box to highlight it, and then click the Set as Source tab to display “Source” in the Source column for that entry in the list box.
ER: Respond to the question “Do you have an Enterprise Reporter?” by clicking the radio button corresponding to either “Yes” or “No”. • If “No” was selected, click SAVE > at the bottom right of the screen to go to Step 3. • If “Yes” was selected, the IP address and Server Name fields display in place of the radio buttons. The < Back button displays above the Server Name field.
Step 3: Server Settings Step 3, the following R3000 server information displays: SMTP Server Settings, Patch Server Settings, PROXY Server Settings, NTP Server Settings: After reviewing the information in this screen, the following actions can now be performed: • To print this information, click the PRINT button. • Click LOGIN to close the wizard and to open the login dialog box of the Threat Analysis Reporter interface so you can begin using the application.
LED Indicators and Buttons SL and MSA Units Front LED Indicators and Buttons for Hardware Status Monitoring LED indicators and buttons for hardware status monitoring display on the front panel, located on the right side of the SL and MSA chassis (see diagrams below).
HL Unit Front LED Indicators and Buttons for Hardware Status Monitoring On an HL unit, the following control panel buttons, icons, and LED indicators for hardware status monitoring display on the right side of the front panel: LED Indicator Key PWR = Power HD = HDD Activity NIC1 = LAN 1 NIC2 = LAN 2 OH = Overheat HL chassis control panel UID = Unique IDentifier The buttons and LED indicators for the depicted icons function as follows: UID (button) – On an HL unit, when the UID button is pressed, a steady
Rear LED Indicators for Hardware Status Monitoring UID (LED indicator) – On the rear of the HL chassis, to the left of the power supplies, a steady blue UID LED indicator displays when the UID button on the control panel is pressed. This LED remains lit until the UID button is pressed again. Power Supplies (LED indicators) – The power supplies are located at the right on the rear of the chassis. An LED indicator is located above each of the power plugs.
HL and SL Units Front LED Indicators for Software and Hardware Status Monitoring On an HL or SL unit, the following LED indicators for software and hardware status monitoring display on the left side of the front panel: LED Indicator Key LOG = Log Download Status RAID = Hard Drive Status DB = Database Status UPDT = Software Update Status left side of the front panel LED Indicator Color Condition Description LOG Green On Downloading a log Off No log download detected On RAID mode enabled and run
Regulatory Specifications and Disclaimers Declaration of the Manufacturer or Importer Safety Compliance USA: UL 60950-1 2nd ed.
Electromagnetic Compatibility Class A Notice Industry Canada Equipment Standard for Digital Equipment (ICES-003) Bureau of Standards Metrology and Inspection (BSMI) - Taiwan 8e6 Threat Analysis Reporter Quick Start Guide 65
EC Declaration of Conformity European Community Directives Requirement (CE) Declaration of Conformity Manufacturer’s Name: 8e6 Technologies Manufacturer’s Address: 828 W.
Tap Installation Appendix: Optional Ethernet Tap Installation This appendix pertains to the optional installation of the Ethernet Tap unit for bandwidth monitoring. Preliminary Setup Procedures Unpack the Ethernet Tap Unit from the Box Open the NetOptics Ethernet Tap box and verify that all accessories are included. Save all packing materials in the event that the unit needs to be returned to 8e6 Technologies.
Tap Installation Install the Ethernet Tap Unit Diagram showing TAR Ethernet Tap installation on the network This step is a continuation from Physically Connect the Unit to the Network in Step 1A or following setup in Step 1B. The procedures outlined in this step require the use of a CAT-5E cable. A. Provide power to the Ethernet Tap by connecting both power cords from the unit to the power source. AC power in rear panel of NetOptics 10/100BaseT Tap B.
Tap Installation C. Using a crossover cable, connect one end to the Switch’s port configured to be the destination port of the Port Mirror. If adding a Threat Analysis Reporter to an existing installation, this port would be the port that was originally occupied by the listening interface of the R3000. D. Connect the other end of the crossover cable to the Ethernet Tap’s Network A port. Ports in front panel of NetOptics 10/100BaseT Tap E.
Index B BSMI 64, 65 C Change Quick Start password 41 crossover cable 67, 69 E EMC 64, 66 F FCC 64 H HL 1, 4, 7, 22, 24, 27, 28, 29, 43, 44, 61, 62, 63, 64, 66 HyperTerminal Setup 30 I ICES-003 64, 65 Install Bezel 22 Install TAP 67 L LCD Panel 27 Login screen 33 LVD 64 M MSA 14, 28, 29, 43, 60, 66 O Overheat 60 P Power Supply Precautions 23 Q Quick Start menu 28, 33, 41, 42 70 8e6 Threat Analysis Reporter Quick Start Guide
R R3000 1, 27, 42, 50, 55, 56, 57, 68, 69 Rack Setup Precautions 6 RAID 1, 63 reboot 45, 47 RoHS compliant 66 S serial port cable 27, 28 shut down 48 SL 1, 4, 11, 22, 27, 28, 29, 43, 44, 60, 63, 64, 66 spare parts kit 4 U UID 61, 62 UL 64 8e6 Threat Analysis Reporter Quick Start Guide 71
8e6 Corporate Headquarters (USA): 828 West Taft Avenue Orange, CA 92865-4232 • Tel: 714.282.6111 or 888.786.7999 Fax: 714.282.6116 (Sales/Technical Support) • 714.282.6117 (General Office) Satellite Office: 8e6 Taiwan: 7 Fl., No. 1, Sec. 2, Ren-Ai Rd., Taipei 10055, Taiwan, R.O.C.
