Specifications

Scanning：
It is convenient for the user to search for calls from other
channels.When“Side Key 2” in the software is programmed
to the scanning function,long press key for two seconds to
enter into the scanning mode,the transceiver will start to scan
with the current channel;Operate it again to exit.
Chinese/English Voice Prompt：
The transceiver has a manual switching function between the
Chinese and the English.Switch to Channel 16,turn off the
transceiver,then press both the power key and key and
meanwhile turn on the transceiver to switch between the
Chinese and English.
Time Out Timer(TOT)：
The purpose of the TOT is to prevent any single person from
using a channel for an extended period of time.An alarm will
sound if the transmission continues beyond the set time.The
transceiver will stop transmission if this occurs.To stop the
alarm,release the PTT key and the transceiver will return to
standby.
Busy Channel Lockout：
The function can prevent interference from other transceivers
using the same channel.
High-Low Power：
The transceiver has a high-low power selection,it can be
programmed.
Keyboard Lockout：
Long press key to lock all buttons,operate it again to unlock.
Power Display：
Short press power key to display the current battery level.
Monitoring：
Long press key for two seconds to enter into the monitor
mode,release it to exit.
VOX：
This function can be voice activated so the user doesn’t have
to press the PTT key.
When “VOX level” in the software is selected,short press
key twice to enter into the VOX mode,then short press key or
key to turn on/off the VOX.
Frequency Range
Supply Power
Memory Channel
Antenna Configuration
Work Mode
Ground Method
Output Power
Modulation Mode
Max.Frequency Deviation
Sparious Radiation
Preemphasis Character
Emission Current
Sensitivity
Audio Power
Audio Distortion
Intermodulation
Interference Resistance
Receiving Current
Standby Current
462-467MHz
DC3.7V
22
Spring Antenna
Co/Differ-frequency Simplex
Communication
Cathode
30.16dBm
FM(F3E）
≤5KHz
≤7.5μW
Per Octave 6dB
≤1000mA
＜0.16μV（12dB SINAD）
≥300mW
＜5%
≥60dB
≤300mA
≤20mA
Technical Parameters
SPECIFICATIONS
TRANSMITTER
RECEIVER
UHF(400-470MHz) Super Receiving
Screen Display
Scanning
Monitoring
VOX
TOT
Chinese/English Voice Prompt
Keyboard Lockout
Power Display
Busy Channel Lockout
High-Low Power Selection
Power Saving Mode
Low Battery Warning
Voice Companding/Scrambling
Function
Programming Encryption Function
Special Signaling
50 CTCSS/208 DCS
Antenna
Display
Screen
PTT
Speaker
Function
Keys
Charging the Battery Pack Icons
1.The battery is not charged in the factory,please charge the
battery under the environmental temperature 5—40℃ before
using.
2.After purchasing or long-term storage(more than two months),
charging the battery for the first time can not reach its saturation
capacity,repeat charge/discharge for twice or three times to
make battery capacity achieve the best state.
3.Before charging,please power off the transceiver,using the
transceiver during charging may affect correct charging.
4.If the battery has been charged fully,please do not charge it
again,otherwise the service life of the battery may be shorten or
may be damaged.
5.If the service time is significantly reduced even after completely
correct charging,the battery can not be used any more,please
replace a new battery.
Power Key
1.Short press keys to adjust the volume.
2.Short press key to switch to channel mode,then short press
keys to adjust the channels.
3.PTT: press this button whenever you wish to talk with the user of
the other radio.
MENU OPERATION
low power channel high power channel volume
scanning channel lockout unlocking
earphone earphone volume transmitting
receiving alarm battery level
Belt Clip
PTT
Earphone
USB
Charging
Port
Desktop
Charger
Connector
Desktop
Charger
Connector
Be Familiar With The Machine
Functions Operation Functions Operation
Battery Power Saving：
If there is no signal or operation,the radio will reduce its power
consumption.The battery power-saving function activates when
the channel is unoccupied or has not been in operation.
Low Battery Warning：
If the battery power falls to the predetermined value during
transmission,the transceiver will give out a voice prompt,please
charge in time.
Scrambling：
It is a voice encryption mode which is different from sub audio.
Companding：
It is a function setting which prevents the inter-channel
interference.
CTCSS/DCS：
The transceiver has 50 CTCSS and 208 DCS,also non-standard
subaudio can be programmed!
Functions Operation
CDCSS Mode：
It is valid only when you program the CDCSS on the channels.
This function has two selections: "normal signaling" and "special
signaling".Normal Signaling refers to the CDCSS codes on the
channels is ordinary codes,we can�talk to�each other with the
same CDCSS;Special Signaling refers to the CDCSS codes on
the channels is special processed codes.When the transceivers
in one company are programmed the same frequency with the
same CDCSS and special signaling,they can avoid the signal
interferences from the other companies’ transceivers.
Functions Operation
▲We May Change The Spe
cifications For Technical Improvement
Without Prior Notice.