Installation Guide

ManualsBrandsA&A Surfaces ManualsFlooring7 in. W x 48 in. L Heritage Urban Oak Rigid Core Click Lock Luxury Vinyl Plank Flooring (52 cases/988.83 sq. ft./pallet)

1. Read enclosed detailed installation instructions before beginning install.

2. A

is a must!

3. Proper moisture testing is a must!

4. Proper expansion around all permanent structures is a must!

5. Molding, trim, transition, and

pieces must not prevent

6. Failure to follow installation instructions will void warranty.

7. Acclimation is normally not necessary but may be required in extreme circumstances.

Please Read All Instructions, Carefully, Before You Begin Installation.

Improper Installation Will Void Warranty

planks for defects such as chips and color variations under good light conditions. Check that

grooves are free of debris. Use planks from multiple boxes during installation to insure random pattern variation.

stacking the cartons. If stacking is necessary, stack the cartons in a crisscross manner - never stacking the cartons more

than three high.

area in which the is installed must remain *climate controlled with the temperature between

65°85°F for the life of the product.

55-95 F (12-53 C ) at least 48-hours before and during the installation, even if temporary temperature measures must be

(5 F) or higher than 95 (53 C), and RH must maintain between

35 – 70%. In these installations, you must use transition moldings at doorways and in any span greater than 40’ in any

*secured to the

top of or fasten trim/molding/transition pieces directly to the

*You may adhere A&A Surfaces Everlife SPC in light commercial and commercial installations using A&A Surfaces

MS007 adhesive, following directions on the pail.

Summary of content (6 pages)

PAGE 1
. 2. 3. 4. 5. 6. 7. Read enclosed detailed installation instructions before beginning install. is a must! A Proper moisture testing is a must! Proper expansion around all permanent structures is a must! Molding, trim, transition, and pieces must not prevent Failure to follow installation instructions will void warranty. Acclimation is normally not necessary but may be required in extreme circumstances. Please Read All Instructions, Carefully, Before You Begin Installation.
PAGE 2
Required Tools and Supplies: • Circular Saw • Safety Glasses • ¼” or ½” spacers • Utility Knife • Straight Edge Ruler or T-Square • Pencil • Tape Measure Underlayment If existing baseboard molding is difficult to remove, Quarter Round molding will be required to cover the expansion space need between flooring and baseboard. SUITABLE TYPES OF SUB FLOORS AND FLOOR PREPARATION The sub floor must be flat, dry, and clean.
PAGE 3
hydrostatic pressure exceeds 6lbs and /or 90% RH, a moisture barrier must be installed over the concrete or you must use multi-use LVT adhesive for the install. Note: New concrete needs to cure for at least 60 days before installing flooring materials. If considering Radiant heat, only Hydronic radiant heat can be used. The heating components must have a minimum of 3/8” separation from the product. System must be operational for a minimum of two weeks prior to installation.
PAGE 4
•Install the second plank in the second row by inserting the short end tongue into the previously installed plank’s groove. Align the plank so that the long side tongue tip is positioned just over the groove lip of the plank in the first row (Figure F). Working from the end seam, at a low angle, insert the long tongue into the groove of the adjoining plank. Very little force is required to fit the tongue into the groove. You should be able to feel the tongue lock into the groove (Figure G).
PAGE 5
Manufacturing Defect: the period of the warranty, this product will be free from manufacturing defects. the Water Proof: floor will not be diminished by exposure to water. Wear Resistance: product and the structural integrity of the wear through to the decorative to improper maintenance or care is not a defect in the wear layer or What is NOT Covered by this Warranty (item list is not exhaustive) • with Installation Instructions is replace material installed with visible imperfections level.
PAGE 6
• • • • • A&A Surfaces Please note: Some jurisdictions do not allow exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitation and exclusion may not apply to you