User manual

Revision History
XAPP794 (v1.3) December 20, 2013 www.xilinx.com 58
Revision
History
The following table shows the revision history for this document.
Notice of
Disclaimer
The information disclosed to you hereunder (the “Materials”) is provided solely for the selection and use of
Xilinx products. To the maximum extent permitted by applicable law: (1) Materials are made available "AS
IS" and with all faults, Xilinx hereby DISCLAIMS ALL WARRANTIES AND CONDITIONS, EXPRESS,
IMPLIED, OR STATUTORY, INCLUDING BUT NOT LIMITED TO WARRANTIES OF
MERCHANTABILITY, NON-INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and (2)
Xilinx shall not be liable (whether in contract or tort, including negligence, or under any other theory of
liability) for any loss or damage of any kind or nature related to, arising under, or in connection with, the
Materials (including your use of the Materials), including for any direct, indirect, special, incidental, or
consequential loss or damage (including loss of data, profits, goodwill, or any type of loss or damage
suffered as a result of any action brought by a third party) even if such damage or loss was reasonably
foreseeable or Xilinx had been advised of the possibility of the same. Xilinx assumes no obligation to
correct any errors contained in the Materials or to notify you of updates to the Materials or to product
specifications. You may not reproduce, modify, distribute, or publicly display the Materials without prior
written consent. Certain products are subject to the terms and conditions of the Limited Warranties which
can be viewed at w
ww.xilinx.com/warranty; IP cores may be subject to warranty and support terms
contained in a license issued to you by Xilinx. Xilinx products are not designed or intended to be fail-safe
or for use in any application requiring fail-safe performance; you assume sole risk and liability for use of
Xilinx products in Critical Applications: w
ww.xilinx.com/warranty.htm#critapps.
Automotive
Applications
Disclaimer
XILINX PRODUCTS ARE NOT DESIGNED OR INTENDED TO BE FAIL-SAFE, OR FOR USE
IN ANY APPLICATION REQUIRING FAIL-SAFE PERFORMANCE, SUCH AS APPLICATIONS
RELATED TO: (I) THE DEPLOYMENT OF AIRBAGS, (II) CONTROL OF A VEHICLE, UNLESS
THERE IS A FAIL-SAFE OR REDUNDANCY FEATURE (WHICH DOES NOT INCLUDE USE
OF SOFTWARE IN THE XILINX DEVICE TO IMPLEMENT THE REDUNDANCY) AND A
WARNING SIGNAL UPON FAILURE TO THE OPERATOR, OR (III) USES THAT COULD
LEAD TO DEATH OR PERSONAL INJURY. CUSTOMER ASSUMES THE SOLE RISK AND
LIABILITY OF ANY USE OF XILINX PRODUCTS IN SUCH APPLICATIONS.
Date Version Description of Revisions
11/22/2012 1.0 Initial Xilinx release.
11/29/2012 1.1 Removed references to targeted reference design (TRD). Updated
Figure 52, page 46 and Figure 53, page 47. Updated the path for the
hardware description files and Zynq device initialization C source code
in Exporting the Base Hardware Platform to SDK, page 46. Added path
for system.bit file in Preparing the SD Card Boot Image, page 53.
01/02/2013 1.2 Added Reference Design File. Updated Figure 26, Figure 27, Figure 29,
Figure 30, and Figure 31.
12/20/2013 1.3 Updated for Vivado 2013.2 design tools. Noise Reduction and Edge
Enhancement cores replaced by Image Enhancement core.
Updated U-boot output in Observing the Linux Console on the Serial
Port. Updated Figure 21, Figure 33, Figure 34, Figure 35, Figure 37,
Figure 39, Figure 40, Figure 41, Figure 42, Figure 42, Figure 43, and
Figure 46. Updated Ta ble 1 1, Ta ble 12 , and Ta bl e 1 4 . Removed Reset
section in System Configuration. Updated Programmable Logic,
Clocking, AXI Interconnect, AXI VDMA, Debugging the Linux
Application, and Linux Kernel Image and Linux Root File System.