ANI-PS112 HD/SD Digital Multi-Format Live Video Production Switcher INSTRUCTION MANUAL A-NeuVideo.com | Frisco, Texas 75034 | (317) 456-2461 V.1.
SAFETY INFORMATION 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 4. Make sure power outlets conform to the power requirements listed on the back of the unit.
TABLE OF CONTENTS CONTENTS SAFETY PRECAUTIONS Introduction & Contents .....................................................2 Features ............................................................................. 2 Specifications ..................................................................... 3 Hardware Description ........................................................4 Connector and Installation .................................................5 Operation Controls and Functions ...................
INTRODUCTION / CONTENTS / FEATURES INTRODUCTION This High Definition HD/SD digital A/V Mixer has (2) input BUSES, each with (6) inputs (2x HDMI’s, 2x Component and 2x S-Video/Composite video) and also a Background Color feature for greater efficiency. The device has 1x HDMI, 2x Components / 2x S-Video or 2x Composite video output ports and also allows you to make adjustments to the position of your video. The compatible output resolutions are HD/SD, NTSC, NTSC-4.
SPECIFICATIONS SPECIFICATIONS SOURCE INPUT: 6 (SOURCE 1/6) • HDMI Input: : 2x Digital Video (480i/p, 576i/p, 720p50/60, 1080i50/60, 1080p50/60) • Component Input: 2x Analog Video YUV(480i/p, 576i/p, 720p50/60, 1080i50/60) • Y/C Input: 2x • Y Signal: 1.0 Vp-p 75Ω, Mini Din 4-pin connector • C Signal: 0.3 Vp-p 75Ω, Mini Din 4-pin connector • Video Input: 2x 1.0 Vp-p 75Ω composite signal, Pin-Jack (NTSC, NTSC 4.
HARDWARE DESCRIPTION FRONT PANEL PHONES: Connect ear phone to listen the audio signal. MIC: Connect the MIC to insert audio. REAR PANEL Source 3 HD stereo audio input 1. Source 4 HD stereo audio input 2. Source 5 SD stereo audio input 1. Source 6 SD stereo audio input 2. Auxiliary Audio input Jack. Program audio out 1 Audio output Jack. Program audio out 2 Audio output Jack. Power ON/OFF Switch. Source 1 HDMI input 1. Source 2 HDMI input 2.
CONNECTOR AND INSTALLATION REAR PANEL CONNECTIONS OUTPUT RESOLUTIONS The output can select HD or SD system. Users can use SD PREVIEW to adjust the output system resolution, or a short cut is to press (2) keys for 1 second simultaneously.
OPERATION CONTROLS AND FUNCTIONS POSITION/TIME Time Control: For adjusting the transition time of the Auto Fade and the Auto Wipe functions. Joystick Control: This joystick control has two functions; control the position of the square wipe pattern and P-IN-P picture.
OPERATION CONTROLS AND FUNCTIONS MODE CONTROL Wipe Button: For selecting the wipe effect. PIP Button: Picture in picture mode can be selected by pressing this button. Mix (Fade) Button: Press this button to select the fade In/Out mode. KEY Button: This button allows you to tune in a best performance point for the blue key and luma key effects. EDGE Button: Used to select sharp edge / soft edge or color edge. COLOR Button: Used to select eight different frame colors.
OPERATION CONTROLS AND FUNCTIONS ADJUST Adjust Button: When LED switched off, the SDP review output side will show AB-bus / output source and output format. When LED illuminate, the user can press / / and buttons to adjust the values. DEMO Button: When LED illuminate, the auto DEMO will switch to ON and the system will auto sequence Demo 96 wipe patterns, press the TIME button to adjust the auto sequence.
OPERATION CONTROLS AND FUNCTIONS AUDIO MIXER INPUT A: Controls the audio level of input A. INPUT B: Controls the audio level of input B. AUX: Controls the audio level of the Auxiliary input. MIC: Controls the audio level of the Microphone input. VIDEO SOURCE SELECT / Used to select Source1,HDMI1. / Used to select Source2,HDMI2. / Used to select Source3,HD input 1. / Used to select Source4,HD input 2. / Used to select Source5,SD input 1.
OPERATION CONTROLS AND FUNCTIONS AUDIO LEVEL Audio level indicator. (Audio level) This indicator shows the audio output level of REC out 1 and REC out 2.
OPERATION BASIC OPERATION Turn the power switch at the rear panel to the ON Position. The LEDs on the panel will light up and the unit is now in initial mode for operation. INPUT SIGNAL SELECTION AND BACKGROUND COLOR SELECTION → Slide the Video slide to the A-bus position. → Press any of the Source thru Source and Background color button. You will see the corresponding picture on the screen. → Press a Background color button to select the background color you need.
OPERATION VIDEO MIX → Press the MIX button . → Press one of the A-bus selection button. → Press one of the B-bus selection button. → Mix effect will be controlled by video slide by sliding A to B or B to A. VIDEO WIPE Reset the operation panel to initial mode: → Press the WIPE button . → Press one of the A-bus selection button. → Press one of the B-bus selection button. → WIPE effect will be controlled by video slide which moves A/B bus outputs horizontally or vertically.
OPERATION WIPE PATTERN SELECTION There are (6) wipe modes available can be selected as follows: → Press the straight wipe button repeatedly to toggle through the available wipe patterns. (4) are available: Left to right, right to left, top to bottom and bottom to top. → Press the corner wipe button repeatedly to toggle through → Press the split wipe button repeatedly to toggle through the available wipe patterns.
OPERATION MULTIPLE PATTERN SELECTION Reset the operation panel to initial mode: → → → → → → Press the WIPE button to place the unit in WIPE mode. Select a wipe pattern e.g. straight wipe by pressing button . Press the MULTI button repeatedly to have the desired multiplication effect. (4) options are available: x1, x2, x4 and x8. Press one of the A-bus selection buttons to select a source. Press one of the B-bus selection buttons to select a source.
OPERATION PICTURE-IN-PICTURE Reset the operation panel to initial mode: → Move the Video Slider fully to the A or B-bus position. → Press one of the A-bus selection buttons to select a source. → Press one of the B-bus selection buttons to select a source. → Press the PIP button to put the unit into picture-in-picture mode. → The PIP mode can be selected by pressing ~ buttons: Shows the picture-in-picture box at 1⁄2 size without the frame edge.
OPERATION KEY Reset the operation panel to initial mode: How to use the LUMA KEY effect: → Press the KEY button to place the unit in KEY mode. → Press one of the A-bus selection buttons to select a source. → Press one of the B-bus selection buttons to select a source. → Press the LUMA KEY button . The darker areas of the picture will become transparent and allow the image of the other source to show through. → Use the Video Slider to control the LUMA KEY level.
OPERATION AUTO FADE/WIPE SELECTION Reset the operation panel to initial mode: → Press the ON button to enter into AUTO FADE/WIPE mode. → FADE/WIPE transition time can be adjusted with the TIME control . → Press the WIPE button to select the wipe effect. → Press the MIX button to select MIX (FADE) effect. → Press the START button to start Auto wipe or fade effect. NOTE: When in AUTO FADE/WIPE mode the Video Slider is disabled.
OPERATION OSD ADJUST Reset the operation panel to initial mode: When turn off the OSD adjust in SD PREVIEW, output will show A/B-bus and output system information. As shown below. INFORMATION A INPUT: HDMI 1 SYSTEM: 1080i60 B INPUT: YPbPr 1 SYSTEM: 480p60 OUTPUT: NTSC F/W Version When turn ON the function in OSD PREVIEW, output will show the adjust screen. As shown below. When in MENU mode, press ◄ ► to adjust the page.
TERMS AND CONDITIONS OF USE PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER A-NeuVideo, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to A-NeuVideo, Inc.