HD-88K INSTRUCTION MANUAL 8x8 UHD 4K2K HDMI MATRIX SWITCH A-NeuVideo.com Frisco, Texas 75034 (317) 456-2461 4K2K HDMI MATRIX SWITCHER SERIES Thank you for purchasing the HD-88K 4K2K HDMI Matrix Routing Switch. You will find this unit easy to install and highly reliable but it is essential that you read this manual thoroughly before attempting to use 8x8 4K2K HDMI Matrix switcher. V1.
SAFETY INFORMATION 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 4. Make sure power outlets conform to the power requirements listed on the back of the unit.
A NEUVIDEO TABLE OF CONTENTS CONTENTS Package Contents .........................................................................1 SAFETY PRECAUTIONS Introduction & Features ..................................................................2 Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply.
A NEUVIDEO INTRODUCTION & FEATURES INTRODUCTION The HD-88K is professional 8x8 matrix routing switch. Supporting (8) HDMI Inputs and (8) HDMI Output supported. The HD-88K is based on the HDMI standard and supports full resolution HDMI Video with embedded HDCP, With a signal bandwidth of 340Mhz, there is no signal degradation. High Definition Digital signals can be selected and distributed to any (8) Inputs to (8) outputs. The Switcher is certified as being fully CEC, ARC and HDCP 1.
A NEUVIDEO SPECIFICATIONS Specifications • Type of Switcher: 8x Inputs to 8x Outputs HDMI Matrix Switch • HDMI Support: HDMI 4K2K, 1080p@60Hz, H36-bit Deep color, 3D of HDMI V1.4 formats • HDCP / CEC Support: HDCP 1.3 Compliant, CEC Compliant • Video Bandwidth: Double Data Rates: 340Mhz, Total 6.
A NEUVIDEO FRONT PANEL FRONT PANEL SWITCH q POWER The power switch turns the unit on and off. The LED will illuminate red to indicate that the switcher is ON and is receiving power. The Switcher will remember that last state during a power cycle. When power is removed and resorted, the last configuration will be evoked. DISPLAY w STATUS Front panel status display shows current matrix routing configuration. This same display also shows particular configuration settings depending on your current function.
A NEUVIDEO FRONT PANEL FRONT PANEL - EDID, MEMORY & RECALL o FUNCTION KEY - EDID a FUNCTION KEY - RECALL s FUNCTION KEY - MEMORY Used to display change current EDID mode. - Press EDID to select new EDID mode or select - Press SOURCE row #1 or #2 Select EDID modes. - Press ENTER to ready memory location. - Or press EDID again to cancel operation. Operation completes. Note : Operation will abort if no keys are pressed within 5 seconds.
A NEUVIDEO FRONT PANEL FRONT PANEL - ALL, OFF, LOCK & ENTER d FUNCTION KEY - ALL Disables (mute) video on all destinations OR Selects the same source to all destinations. Option 1 - Press ALL followed by OFF button. The display will show “ 0 “ indicating all destinations have no video selected. Option 2 - Press ALL followed by Source 1 thru 8. The display will show the Source selected. - Press ENTER The pre-set source selection will be assigned all destinations.
A NEUVIDEO REAR PANEL REAR PANEL POWER INLET q DC The Switcher is fitted with a DC power plug input connector. Ensure that the used is of an approved type and is of sufficient current carrying connector capacity with the correct voltage and connector polarity. 12Volt DC power supply 5A Max (Center pin positive). EXTENDER CONTROL w IRSupport one of IR Extender. Extend distance maximum 300 Meters / ~984 feet.
A NEUVIDEO TYPICAL APPLICATION INSTALLING DIAGRAM Samples Connection: Using IR External, RS-232 or Ethernet command to control Switcher HD-88K via PC or HD-100 IR receiver transmit the HD-88K’s IR signal. NOTE: 1. Switcher IR External port : Use HD-100 IR signal Receiver. 2. 4K2K Source: Use 4K2K Blu-ray HD Source. 3. Control Switch via a PC RS-232. 4. Control Switch via a PC Ethernet. Application RS-232, IR and Ethernet control the Switcher.
A NEUVIDEO REMOTE CONTROL Before making any connections to the switcher. Observe the following: • Ensure the mains voltage supply matches the label on the supplied plug-pack (+/- 10%) • Ensure that the power switch is OFF • Ensure that all system grounds (earth) are connected to a common point.
A NEUVIDEO REMOTE CONTROL IR REMOTE CUSTOM AND DATA CODES (NEC Standard) HOW TO SETUP IR CODES : Model number : HD-88K CUSTOM CODE : 8A75 ALL: 8A75 B04F POWER ON: 8A75 A15E OFF: 8A75 B14E POWER OFF: 8A75 A25D EDID: 8A75 B748 LOCK: 8A75 B54A RECALL: 8A75 B24D MEMORY: 8A75 B44B ENTER: 8A75 B34C PRESS DESTINATION then - # PRESS SOURCE - # DESTINATION #1 : 8A75 DESTINATION #2 : 8A75 DESTINATION #3 : 8A75 DESTINATION #4 : 8A75 DESTINATION #5 : 8A75 DESTINATION #6 : 8A75 DESTINATION
A NEUVIDEO EDID FUNCTION EDID function for HDMI Matrix Switcher EDID setup To change the EDID setup Step 1. Press the EDID button The display will show the currently selected EDID mode Step 2. Press SOURCE #1 or #2 button row The button will flash blue and the display will show the current Embedded EDID Status. To set EDID mode. The switcher will return to operation mode. Step 3. Press the ENTER button Operation will abort if no keys are pressed within 5 seconds.
A NEUVIDEO EDID FUNCTION EDID function : 7x Embedded EDID Modes Mode 1. FSS® (Fast Speed Start) Fast Speed Start mode shortens the startup time of the switcher. Selecting this mode does not force the EDID setup to be cancelled. Users may first select one EDID mode from mode 2 to 3, and then select mode 1 for fast speed start. Mode 2. H24-3D (1080p-24 bits) Audio Support : PCM 2CH Mode 3. H24-3D-M (1080p-24bits) Audio Support : MAT(MLP) 7.1CH, PCM 2CH, One Bit Audio 2CH, AC-3 5.1CH, DTS 5.1CH, PCM 7.
A NEUVIDEO EDID FUNCTION EDID LEARNING MODE Learning EDID Single to Single Example : Learn Destination #8 EDID To Source #5. Step 1. Press the EDID button The button will flash blue and the display will show the current Embedded EDID Status. Step 2. Press the Destination #8 button row Copy the Destination #8 Display EDID. Step 3. Press the Source #5 button row Learning the Destination #8 EDID To Source # 5. Step 4. Press ENTER button To confirm entries.
A NEUVIDEO EDID FUNCTION EDID SINGLE LEARNING MODE 1 LEARNING EDID MODE-#1 Single Learning Mode#1 EDID setup Key Press Sequence: EDID > DESTINATION # > SOURCE # > ENTER The EDID for HDMI has been learned from the Destination port to the Source port. Learning EDID from Destination to Source Press EDID > DESTINATION > SOURCE > ENTER 1. Press EDID button The LCM will show the current EDID status. 2. Press DESTINATION button Press DESTINATION (#1 thru #8) The LCM will show the LEARNING HDMI.
A NEUVIDEO EDID FUNCTION EDID SINGLE LEARNING MODE 2 LEARNING EDID #2 Multiple Learning mode #2 EDID setup Passing EDID from Destination to Source 1. Press EDID button Key Press Sequence: EDID > OFF > DESTINATION #1 thru #8 > ENTER The EDID for HDMI has been Learned from the Destination port to the Source port. The LCM will show the current EDID status. 2. Press OFF button The LCM will show the current EDID LEARN status. 3.
A NEUVIDEO IR EXTENDER REAR PANEL IR EXTENDER PORT 1. HD-100 IR 300M Receiver Switcher IR EXT. In Cable (3C) Distance: Max.300M IR Receiver (HD-100) IR PN#: SW-HDXX R oHS /95/E C IR E XT. in RS - 232 IR EXT .
RS-232 & ETHERNET SERIAL INTERFACE A NEUVIDEO RS-232 SERIAL INTERFACE CONNECT a PC or CONTROL SYSTEM VERSION COMPATIBLE V1.0 & V1.5 For a complete list of commands, please reference external document extended RS-232 Protocol Instruction Manual.
A NEUVIDEO TERMS AND CONDITIONS OF USE PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER A-NeuVideo, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to A-NeuVideo, Inc.