Remote Touch Displa y ACD-521R ACD-521R 21.
Remote Touch Displa y ACD-521R Copyright Notice This document is copyrighted, 2014. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Remote Touch Displa y ACD-521R Acknowledgments ® ® Intel is registered trademarks of Intel Corporation. IBM, PC/AT, PS/2 are trademarks of International Business Machines Corporation. ® Microsoft Windows is a registered trademark of Microsoft ® Corporation. RTL is a trademark of Realtek Semi-Conductor Co., Ltd. C&T is a trademark of Chips and Technologies, Inc. UMC is a trademark of United Microelectronics Corporation.
Remote Touch Displa y ACD-521R Packing List The LCD monitor comes with the following standard parts shown as below. Check and make sure they are included and in good condition. If anything is missing or damaged, contact the dealer immediately. 1 ACD-521R 1 Utility CD-ROM Contains User’s Manual (in PDF format), Drivers and Utilities 1 AC/DC 12V Power Adapter with Lock If any of these items are missing or damaged, you should contact your distributor or sales representative immediately.
Remote Touch Displa y ACD-521R Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
Remote Touch Displa y ACD-521R 14. If any of the following situations arises, get the equipment checked by service personnel: a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment does not work well, or you cannot get it to work according to the users manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15.
Remote Touch Displa y ACD-521R Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Display 有毒有害物质或元素 部件名称 铅 汞 镉 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 外壳 × ○ ○ ○ ○ ○ 液晶模块 × ○ ○ ○ ○ ○ 触控模块 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 印刷电路板 六价铬 多溴联苯 多溴二苯醚 及其电子组件 外部信号 连接器及线材 O:表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X:表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注: 一、此产品所标示之环保使用期限,系指在一般正常使用状况下。 二、上述部件物质触控模块为选购品。
Remote Touch Displa y ACD-521R Contents Chapter 1 General Information 1.1 Introduction ................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 General Specification ................................................ 1-4 1.4 Dimension ................................................................. 1-7 1.5 Network Topology .....................................................
Remote Touch Displa y ACD-521R 3.3 Select Input Source. .................................................. 3-4 3.4 Contrast/ Brightness- Submenu. ............................... 3-5 3.5 Geometry Menu......................................................... 3-6 3.6 Color Temperature- Submenu OSD Main Menu: Push The MENU Keys. ............................................................. 3-7 3.7 RGB Color- Submenu. .............................................. 3-8 3.8 Language- Submenu. ...................
Remote Touch Displa y ACD-521R Chapter 1 General Information Chapter 1 General Information 1-1
Remote Touch Displa y ACD-521R 1.1 Introduction Thank you for purchasing of the Infotainment Touch Display with Remote Display Technology - a marvelous contribution of cutting-edge technology. The LCD monitor has been designed with serious thoughts to present the best performance for most applications. Symbol of elegance, its compact and slim profile are well suited in working locations where space is at a premium. The TFT LCD monitor displays sharper, more brilliant, crisper and flicker-free images.
Remote Touch Displa y ACD-521R 1.2 Features 21.
Remote Touch Displa y ACD-521R 1.3 General Specification System Input signal VGA, DVI Control OSD (On Screen Display) on the panel I/O connector USB x 3 (optional 2 on front, 1 on rear), LAN x 2, Line-out x 1, 2W speaker x 2 OS Support Windows ® XP (T/S: Single point), Linux ® Fedora (T/S: Single point), Windows 7 (T/S: Single point) Mechanical Construction IP65/NEMA4 for plastic front bezel, IPx1 for plastic chassis Mounting VESA 75/100 Dimension 18.11” x 12.2” x 2.
Remote Touch Displa y ACD-521R Temperature Storage -4°F~ 140°F (-20°C to 60°C) Temperature Storage 10%~95% @ 40°C, non-condensing Humidity Vibration 1g rms/5-500Hz/random operation Shock 15 G peak acceleration (11 msec. duration) EMC CE/FCC Class A Power Supply DC Input DC 12V, w/AC power adapter w/lock Display Type 21.5" LED backlight Max. 1920x1080 LCD Resolution Max. Colors 16.
Remote Touch Displa y ACD-521R Touchscreen Type Projected Capacitive Multi-Touch ® (Windows 7) Light 90% Transmission Chapter 1 General Information 1-6
Remote Touch Displa y ACD-521R 1.
Remote Touch Displa y ACD-521R 1.5 Network Topology 1. One-to-one Network The purpose of a one-to-one network is to allow a display to be used anywhere away from the host PC. The display can be placed at any location with Ethernet access. The entire VGA/DVI signal will be transmitted from a host PC to a remote display via the Ethernet. 2. One-to-Multiple Network The one-to-multiple network is a special design for digital signage applications to show the same screen/audio in different display monitors.
Remote Touch Displa y ACD-521R 3. Cascade Network The purpose of a cascade network is to save on cabling installation costs. It is specially designed for digital signage applications with limited space such as trains, buses and airports. With a cascade network set up, an end user can deploy digital signage displays easily and save on installation costs.
Remote Touch Displa y ACD-521R Chapter 2 Hardware Installation Chapter 2 Hardware Installation 2-1
Remote Touch Displa y ACD-521R 2.1 Before Unpacking It is very important to place the LCD Display in a suitable environment. The surface for placing the LCD Display should be stable and level. Make sure the place has good ventilation, and out of direct sunlight; away form sources of excessive dust, dirt, heat, water, moisture and vibration. Convenience for connecting the LCD Display the related facilities should be well considered too.
Remote Touch Displa y ACD-521R 2.2 Connecting Power and Cables To power on the LCD Display, use the provided AC-DC adapter and the power cord to connect to the power output socket of the monitor. Fasten the connector securely.
Remote Touch Displa y ACD-521R 2.3 VESA Wall Mounting Mounting the LCD Display with UL Listed Wallmount Bracket only. The LCD Display can be mounted on a monitor arm or wallmount plate. Caution: When mounting the LCD Display, take care to tighten the retention screws or bolts until fully secured, but do not over tighten. Over tighting the retention screws or bolts may cause them to become stripped, rendering them useless.
Remote Touch Displa y ACD-521R 2.4 LED Definitions Red LED Green LED Off Condition Power off Static Static Link established Static Flash Link in process Flash Off Load firmware 2.5 Button Definitions There are three buttons on remote gateway and display. Refer to the following LED definitions.
Remote Touch Displa y ACD-521R ACD-521R-A2 (One-to-one Network) Short Press Long press on Reset (Press until Red LED blinking) Long Press on Reset (Press until both Red LED and Green LED Blinking) SW1 SW2 Link on: Link (Default) Link off: Unlink Video Mode* (Default) Graphic Mode* Engineering Mode* N/A Engineering Mode* and Reset to default* N/A *1: Graphic mode: The system will get better performance of graphic/text in the screen. But it would occupy larger bandwidth of the network.
Remote Touch Displa y ACD-521R will cause compatibility issues. Operation: The button event is triggered correctly at the remote display side, when system is setup correctly for one-to-multiple. The selected EDID will be update to Host Side EEPROM (HU7). The same operation applies for Loopback EDID. In the system setup, the last EDID updated will stay in the EEPROM. If customers setup this button even many times, the last one triggered will be applied. 2.
Remote Touch Displa y ACD-521R 2.7 Connecting Power of Remote Display Use the provided AC-DC adapter and the power cord to connect the power output socket of the monitor to turn on the power. A ”Surge Protection” device plugged between the AC-DC adapter and the wall outlet is recommended to prevent the effects of sudden current variations from reaching the LCD monitor. The sudden peaks of electricity may harm the LCD monitor. 2.
Remote Touch Displa y ACD-521R box may have some issues, so the IP address of the remote box cannot be found Below is the situation, which is searching the IP address If the display or sound cannot work properly, please try the following steps. Make sure the local and remote IP can be found. If the IP address cannot be found, please check the network cabling Make sure the DVI/VGA and audio cable insert tightly 2.
Remote Touch Displa y ACD-521R Chapter 3 On Screen Display Control Chapter 3 On Screen Display Control 3-1
Remote Touch Displa y ACD-521R 3.1 On Screen Display (OSD) Board Description Buttons Description Turn the monitor power ON or OFF. Activate the OSD menu. Enter/confirm the selected option. Move the selector to the next option. UP / Right / Increase / Increase the gauge value of the Input select selected option. Power Menu / Enter Down/ Left / Decrease Change input source. Move the selector to the previous option. Decrease the gauge value of the selected option.
Remote Touch Displa y ACD-521R 3.
Remote Touch Displa y ACD-521R 3.
Remote Touch Displa y ACD-521R 3.
Remote Touch Displa y ACD-521R 3.
Remote Touch Displa y ACD-521R 3.
Remote Touch Displa y ACD-521R 3.
Remote Touch Displa y ACD-521R 3.
Remote Touch Displa y ACD-521R 3.
Remote Touch Displa y ACD-521R 3.
Remote Touch Displa y ACD-521R 3.
Remote Touch Displa y ACD-521R Chapter 4 Touch Screen Driver Installation Chapter 4 Touch Screen Driver Installation 4-1
Remote Touch Displa y ACD-521R 4.1 Introduction The optional ACD-521R Series touch screen uses Projected Capacitive Multi-Touch technology to provide more accurate sensing capacity than other technologies. The touch screen is specially designed for infotainment environments, and has been approved by FCC Class A standards. ® ® 4.2 Installing Driver for Windows XP/ Windows 7 / Linux ® ® The touch screen has drivers for Windows XP、 Windows 7 and Linux .
Remote Touch Displa y ACD-521R 1-3. Select Terminal 1-4. Input Commandsu and System Password 2.
Remote Touch Displa y ACD-521R 2-1 Input commandls (This is the lowercase L) 2-2 all files of desktop will appear in window. (Please copy the driver on desktop first.) 2-3 Input commandcd eGTouch_v1.00.0726.
Remote Touch Displa y ACD-521R 2-4 Input commandls (This is the lowercase L) 2-5 The information of the folder, “eGTouch_v1.00_0726.L-x32”, would appear in the window.
Remote Touch Displa y ACD-521R 3. Reboot 4. Change the permission Input commandchmod△777△/etc/eGTouchd.ini 5. Select Computer (You can modify the value of the Y axis to reverse action principle.
Remote Touch Displa y ACD-521R 6. Select “File System” 7. Select the “etc” folder 8. Select the “eGTouchd.
Remote Touch Displa y ACD-521R 9. Select “Display” 10.
Remote Touch Displa y ACD-521R 11. Execute “Save” Note: If you want to change X or Y axis, please refer to the description of “Direction” as red circle below. 12.
Remote Touch Displa y ACD-521R 13 . Input command./eGTouch (Execute Driver) and select the file of “eGTouch32”. 13-1. Input command./EventTest (Execute AP) 14. Draw and test (Drawing、Writing) 15. If you want to replace the Interface, please remove the Touchd Driver Input commandsh setup.sh uninstall (Must Under eGTouch_v1.00.0726.
Remote Touch Displa y ACD-521R 16.