Multi-Touch Panel PC ACP-5187 ACP-5187 ® 18.
Multi-Touch Panel PC ACP-5187 Copyright Notice This document is copyrighted, 2013. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Multi-Touch Panel PC ACP-5187 Acknowledgments ® TM ® Intel , Core Microsoft Windows is a registered trademark of Microsoft are registered trademarks of Intel Corporation. ® ® Corporation. RTL is a trademark of Realtek Semi-Conductor Co., Ltd. C&T is a trademark of Chips and Technologies, Inc. UMC is a trademark of United Microelectronics Corporation. ITE is a trademark of Integrated Technology Express, Inc.
Multi-Touch Panel PC ACP-5187 Packing List Before you begin installing your Panel PC, please make sure that the following items have been shipped: ACP-5187 Infotainment Multi-Touch Panel PC Power Adapter x 1 Product DVD Contains User’s Manual (in PDF format), Drivers and Utilities If any of these items are missing or damaged, you should contact your distributor or sales representative immediately.
Multi-Touch Panel PC ACP-5187 Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
Multi-Touch Panel PC ACP-5187 14. If any of the following situations arises, get the equipment checked by service personnel: a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment does not work well, or you cannot get it to work according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15.
Multi-Touch Panel PC ACP-5187 Classification 1. Degree of production against electric shock: not classified 2. Degree of protection against the ingress of water: IPX1 3. Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide. 4. Mode of operation: Continuous 5.
Multi-Touch Panel PC ACP-5187 FCC This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation.
Multi-Touch Panel PC ACP-5187 Safety Symbol Description The following safety symbols are further explanations for your reference. Medical equipment with respect to electric shock, fire and mechanical hazards only in accordance with UL 60601-1, and CAN/CSA C22.2 NO. 601.1 Attention, consult ACCOMPANYING DOCUMENTS. Ground wire Protective Ground wire. Medical equipment with respect to electric shock, fire and mechanical hazards only in accordance with UL 60601-1, and CAN/CSA C22.2 NO. 601.
Multi-Touch Panel PC ACP-5187 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Panel PC/ Workstation 有毒有害物质或元素 部件名称 铅 汞 镉 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 硬盘 × ○ ○ ○ ○ ○ 液晶模块 × ○ ○ ○ ○ ○ 光驱 × ○ ○ ○ ○ ○ 触控模块 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 印刷电路板 六价铬 多溴联苯 多溴二苯醚 及其电子组件 外部信号 连接器及线材 外壳 中央处理器 与内存 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含
Multi-Touch Panel PC ACP-5187 Contents Chapter 1 General Information 1.1 Introduction ................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specification .............................................................. 1-4 1.4 General Information................................................... 1-7 Chapter 2 Hardware Installation 2.1 Safety Precautions .................................................
Multi-Touch Panel PC ACP-5187 Appendix B I/O Information B.1 I/O Address Map ....................................................B-2 B.2 Memory Address Map ............................................B-4 B.3 IRQ Mapping Chart ..............................................B-5 B.4 DMA Channel Assignments ...................................B-5 Appendix C Miscellanea C.1 General Cleaning Tips .......................................... C-2 C.2 Cleaning Tools ...................................................
Multi-Touch Panel PC ACP-5187 Chapter 1 General Information Chapter 1 General Information 1-1
Multi-Touch Panel PC ACP-5187 1.1 Introduction The ACP-5187 is a Multi-Touch Infotainment Panel PC with ® ® superior onboard Intel Core™ i7/i5/Celeron processor-based computer. It is a PC-based system with 18.5” true color TFT LCD display, integrated multimedia functions make them the perfect platforms to build comprehensive lifestyle computing applications. The ACP-5187 includes all the features of a powerful computer into a slim and attractive chassis.
Multi-Touch Panel PC ACP-5187 1.2 Features 18.5” WXGA (1366 x 768) Fanless TFT LCD Display Easy-To-Clean: Multi-Touch Window Design (Two-Point) Superior Intel Core™ i7-3610QE/ Core™ i5-3610ME/ ® ® Celeron 1020E Processor IPx1 100% Water-Proof from the Top Plastic Housing Anti-Scratch Surface (7H Hardness) IPX1 WebCam (Optional) USB x 6, COM x 1.
Multi-Touch Panel PC ACP-5187 1.3 Specification System Processor ® Onboard Intel Core™ i7/ Core™ i5 / ® Celeron Processor System Memory DDR3 SODIMM x 1, Max. 8 GB (Default 2GB) ® LCD / CRT Controller Integrated graphics in Intel QM77 I/O Port USB x 6 (USB2.0 x 2 on side; USB2.0 x 2 and USB3.0 x 2 on bottom) RS-232 x 1 LAN x 2 Line-out x 1 DVI-I x 1 Power input x 1 2W speaker x 2 ATX power button Storage Disk Drive 2.
Multi-Touch Panel PC ACP-5187 Mechanical Construction IPX1 from the top plastic housing Mounting VESA 100 Dimension 18.11”(W) x 12.2”(H) x 3.39”(D) (460mm x 310mm x 86mm) Carton Dimension 26” x 8.11” x 19.53’’ (661mm x 206mm x 496mm) Net Weight 15.4 lb (7 kg) Gross Weight 19.
Multi-Touch Panel PC ACP-5187 LCD Display Type 18.5” TFT-LCD, CCFL Max. Resolution 1366 x 768 Max. Colors 16.
Multi-Touch Panel PC ACP-5187 1.4 General Information 1.
Multi-Touch Panel PC VESA 100 Mounting Holes Mounting Holes Chapter 1 General Information 1-8 ACP-5187
Multi-Touch Panel PC ACP-5187 RS-232 USB x 2 USB x 2 DVI-I Power Input Smart Card Reader (Optional) Power Switch Line-out USB x 2 LAN x 2 Antenna (Optional) Antenna (Optional) Chapter 1 General Information 1-9
Multi-Touch Panel PC ACP-5187 Chapter 2 Hardware Installation Chapter 2 Hardware Installation 2-1
Multi-Touch Panel PC ACP-5187 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
Multi-Touch Panel PC ACP-5187 2.2 COM2 Pin8 Function Selection (JP8) +12V Ring JP8 Function 1-2 +12V 3-4 Ring (Default) 5-6 +5V +5V 2.3 Clear CMOS (JP11) 1 2 3 1 2 3 Normal Clear CMOS JP11 Function 1-2 Normal (Default) 2-3 Clear CMOS 2.
Multi-Touch Panel PC ACP-5187 5 TX OUT ±9V 6 CTS IN 7 DTR OUT ±9V 8 RI/+5V/+12V IN/ PWR +5V/+12V 9 GND GND Pin Pin Name Signal Type Signal Level 1 RS422_TX- OUT ±5V 2 NC 3 RS422_RX+ 4 NC 5 RS422_TX+ 6 NC 7 RS422_RX- IN 8 NC/+5V/+12V PWR 9 GND GND Pin Pin Name Signal Type Signal Level 1 RS485_D- I/O ±5V 2 NC 3 NC 4 NC 5 RS485_D+ I/O ±5V RS-422 IN OUT ±5V +5V/+12V RS-485 Chapter 2 Hardware Installation 2-4
Multi-Touch Panel PC ACP-5187 6 NC 7 NC 8 NC/+5V/+12V PWR 9 GND GND +5V/+12V Note: COM2 RS-232/422/485 can be set by BIOS setting. Default is RS-232. Pin 8 function can be set by JP8. 2.
Multi-Touch Panel PC ACP-5187 2.6 A Quick Tour of the ACP-5187 Mechanical Drawing ACP- 5 1 8 7 Un i t s :m m 86.4 56.0 460.0 Front Chapter 2 Hardware Installation 2-6 VESA 1 0 0 1 0 0 .0 1 6 0 .0 8 2 .6 310.0 1 0 0 .
Multi-Touch Panel PC ACP-5187 Rear I/O Chapter 2 Hardware Installation 2-7
Multi-Touch Panel PC ACP-5187 Cable Cover (Optional) Note 1: You may turn on the power by cutting and destroying the protective cover as it shows below.
Multi-Touch Panel PC ACP-5187 2.7 2.
Multi-Touch Panel PC Step 3: Remove HDD Bracket (4 screws) Step 4: Get the HDD and HDD Bracket ready Chapter 2 Hardware Installation 2-10 ACP-5187
Multi-Touch Panel PC ACP-5187 Step 5: Fasten the four screws to fix HDD Bracket and HDD Step 6: Connect the SATA and power cables to the HDD and fasten the four screws to fix the HDD Bracket Chapter 2 Hardware Installation 2-11
Multi-Touch Panel PC ACP-5187 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
Multi-Touch Panel PC ACP-5187 3.1 System Test and Iinitialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. System configuration verification These routines check the current system configuration stored in the CMOS memory and BIOS NVRAM.
Multi-Touch Panel PC ACP-5187 3.2 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM and BIOS NVRAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
Multi-Touch Panel PC ACP-5187 Setup Menu Setup submenu: Main Options summary: (default setting) System Date Day MM:DD:YYYY Change the month, year and century. The „Day‟ is changed automatically. System Time HH : MM : SS Change the clock of the system.
Multi-Touch Panel PC ACP-5187 Setup submenu: Advanced Options summary: (default setting) ACPI Settings System ACPI Parameters Trusted Computing Trusted Computing Settings CPU Configuration CPU Configuration Parameters SATA Configuration SATA Device Options Settings Chapter 3 AMI BIOS Setup 3-5
Multi-Touch Panel PC Intel TXT(LT) Configuration Intel Trusted Execution Technology AMT Configuration AMT Configuration Parameters USB Configuration USB Configuration Parameters H/W Monitor Monitor hardware status Super IO Configuration Super IO Configuration Parameters Chapter 3 AMI BIOS Setup 3-6 ACP-5187
Multi-Touch Panel PC ACP-5187 ACPI Settings Options summary: (default setting) Enabled Enable Hibernation Disabled Enabled or disabled hibernate (OS/S4 Sleep State).
Multi-Touch Panel PC ACP-5187 Disabled Enabled or disabled wake on ring function. RTC Wake Settings Options summary: (default setting) Wake system with Disabled Fixed Time Enabled Enable or disable System wake on alarm event. Wake up time is setting by following settings.
Multi-Touch Panel PC Wake up minute 0-59 Wake up second 0-59 Wake system with Disabled Dynamic Time Enabled ACP-5187 Enable or disable System wake on alarm event. Wake up time is current time + Increase minutes.
Multi-Touch Panel PC ACP-5187 Options summary: (default setting) Security Device Support Disabled Enabled En/Disable TPM support. TPM State Disabled Enabled En/Disable TPM functionality. Pending TPM Operation None Enable Take Ownership Disable Take Ownership TPM Clear Select one-time TPM operation. Item value returns to „None‟ after next POST.
Multi-Touch Panel PC ACP-5187 CPU Configuration Options summary: (default setting) Hyper-Threading Disabled Enabled En/Disable CPU Hyper-Threading function Active Processor Cores ALL 1 to Max CPU cores Number of CPU cores to be active.
Multi-Touch Panel PC Enabled En/Disable XD bit for supporting OS Intel Virtualization Disabled Technology Enabled En/Disable Intel VT-x function EIST Disabled Enabled En/Disable Intel SpeedStep Turbo Mode Disabled Enabled En/Disable Intel Turbo Mode SATA Configuration Chapter 3 AMI BIOS Setup 3-12 ACP-5187
Multi-Touch Panel PC ACP-5187 Options summary: (default setting) SATA Controller(s) Disabled Enabled En/Disable SATA controller Configure SATA as IDE AHCI RAID Available for QM77 Sku Configure SATA controller operating as IDE/AHCI/RAID mode. Port 1/Port 2/CFast Disabled Slot Enabled En/Disable the selected port. Hot Plug Disabled Enabled En/Disable Hot Plug feature for specified port.
Multi-Touch Panel PC ACP-5187 Intel TXT(LT) Configuration Options summary: (default setting) Intel TXT(LT) Support Disabled Enabled En/Disable Intel TXT function. This function only can be enabled/disabled if SMX, VT-x and VT-d support are enabled prior to it.
Multi-Touch Panel PC ACP-5187 AMT Configuration Options summary: (default setting) Intel AMT Enabled Disabled En/Disable Intel® Active Management Technology BIOS Extension. Note: iAMT H/W is always enabled. This option just controls the BIOS extension execution.
Multi-Touch Panel PC ACP-5187 USB Configuration Options summary: (default setting) Legacy USB Support Enabled Disabled Auto Enables BIOS Support for Legacy USB Support. When enabled, USB can be functional in legacy environment like DOS. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI application USB3.
Multi-Touch Panel PC ACP-5187 Enables BIOS Support for USB3.0 (XHCI). When disabled, PCH USB3.0 controller will also be disabled. Device Name Auto (Emulation Type) Floppy Forced FDD Hard Disk CD-ROM If Auto. USB devices less than 530MB will be emulated as Floppy and remaining as Floppy and remaining as hard drive. Forced FDD option can be used to force a HDD formatted drive to boot as FDD(Ex.
Multi-Touch Panel PC ACP-5187 Super IO Configuration Options summary: (default setting) Serial Port 1/2 Configuration Set Parameters of Serial Port 1/2 Power Off Restore AC Power Loss Power On Last State Select AC power state when power is re-applied after a power failure.
Multi-Touch Panel PC ACP-5187 Configure Energy-using Product(EuP) Power Control. Serial Port 1 Configuration Options summary: (default setting) Serial Port Disabled Enabled En/Disable specified serial port.
Multi-Touch Panel PC IO=2F8h; IRQ=3,4,5,7,10,11,12; IO=3E8h; IRQ=3,4,5,7,10,11,12; IO=2E8h; IRQ=3,4,5,7,10,11,12; Select a resource setting for Super IO device.
Multi-Touch Panel PC ACP-5187 En/Disable specified serial port. Change Settings Auto IO=2F8h; IRQ=3; IO=3F8h; IRQ=3,4,5,7,10,11,12; IO=2F8h; IRQ=3,4,5,7,10,11,12; IO=3E8h; IRQ=3,4,5,7,10,11,12; IO=2E8h; IRQ=3,4,5,7,10,11,12; Select a resource setting for Super IO device. Device Type RS232 RS422 RS485 Configure COM2 operated as RS232, RS422 or RS485.
Multi-Touch Panel PC Setup submenu: Chipset Options summary: (default setting) Onboard Device Configure Onboard Devices PCI-IO Configuration South Bridge Parameters Memory Configuration Memory Parameters Graphic Configuration Graphic Parameters Chapter 3 AMI BIOS Setup 3-22 ACP-5187
Multi-Touch Panel PC ACP-5187 Onboard Device Options summary: (default setting) Onboard HD Audio Disabled Enabled Auto En/Disabled HD Audio controller. HD Audio Internal Enabled HDMI Codec Disabled En/Disabled internal HDMI codec for HD Audio.
Multi-Touch Panel PC En/Disabled Intel i82579 NIC Realtek LAN Controller Enabled Disabled En/Disabled Realtek RTL8111E NIC PCH-IO Configuration Options summary: (default setting) Power Mode ATX Type Select the power type used on the system PCIe MiniCard Slot Disabled Enabled Control the PCI Express Root Port.
Multi-Touch Panel PC PCIe Speed ACP-5187 Auto Gen1 Gen2 Select PCI Express port speed. Some PCIe carsd must set to Gen1 for operation.
Multi-Touch Panel PC Memory Frequency Auto Limiter 1067 ACP-5187 1333 1600 Maximum Memory Frequency Selections in Mhz. Max TOLUD Dynamic 1 GB 1.25 GB 1.5 GB 1.75 GB 2 GB 2.25 GB 2.5 GB 2.75 GB 3 GB 3.25 GB Maximum Value of TOLUD. Dynamic assignment would adjust TOLUD automatically based on largest MMIO length of install graphic controller.
Multi-Touch Panel PC ACP-5187 Graphic Configuration Options summary: (default setting) Primary Display Auto IGFX PCI Select graphic adapters to boot Internal Graphics Auto Disabled Enabled En/Disabled internal graphics device GTT Size 1MB Chapter 3 AMI BIOS Setup 3-27
Multi-Touch Panel PC ACP-5187 2MB Select the GTT Size Aperture Size 128MB 256MB 512MB Select the Aperture Size DVMT Pre-Allocated 64MB 32MB~1024MB Select DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the Internal Graphics Device. DVMT Total Gfx Mem 128MB 256MB Max Select DVMT 5.0 Total Graphic Memory size used by the Internal Graphics Device.
Multi-Touch Panel PC ACP-5187 LCD Control Options summary: (default setting) Primary IGFX Boot Auto Detect Display DVI-A LVDS1 DVI-D Select Primary IGFX boot display device Note: LVDS1 is the default main display device when this item set to “Auto Detect” and LVDS1 enabled. In this case, DVI will not display under DOS environment unless user set this item to DVI manually.
Multi-Touch Panel PC LVDS1(Internal) ACP-5187 Enabled Enable Internal LVDS LVDS1 Panel Type 1366x768 1366x768 24-Bit resolution.
Multi-Touch Panel PC ACP-5187 Setup submenu: Boot Options summary: (default setting) Quiet Boot Disabled Enabled En/Disable showing boot logo.
Multi-Touch Panel PC ACP-5187 Boot Option #X/ XXXX Drive BBS Priorities The order of boot priorities.
Multi-Touch Panel PC ACP-5187 Setup submenu: Security Options summary: (default setting) Administrator Not set Password/ User Password Chapter 3 AMI BIOS Setup 3-33
Multi-Touch Panel PC ACP-5187 You can install a Supervisor password, and if you install a supervisor password, you can then install a user password. A user password does not provide access to many of the features in the Setup utility. Install the Password: Press Enter on this item, a dialog box appears which lets you enter a password. You can enter no more than six letters or numbers. Press Enter after you have typed in the password. A second dialog box asks you to retype the password for confirmation.
Multi-Touch Panel PC ACP-5187 Setup submenu: Exit Options summary: (default setting) Save Changes and Reset Reset the system after saving the changes Discard Changes and Reset Reset system setup without saving any changes Restore Defaults Restore/Load Default values for all the setup options.
Multi-Touch Panel PC ACP-5187 Chapter 4 Driver Installation Chapter 4 Driver Installation 4-1
Multi-Touch Panel PC ACP-5187 The ACP-5187 comes with an AutoRun DVD-ROM that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver DVD, the driver DVD-title will auto start and show the installation guide. If not, please follow the sequence below to install the drivers.
Multi-Touch Panel PC 4.1 ACP-5187 Installation: Insert the ACP-5187 DVD-ROM into the DVD-ROM drive. And install the drivers from Step 1 to Step 10 in order. Step 1 – Install Chipset Driver 1. Click on the STEP 1-CHIPSET folder and select the OS folder your system is 2. Double click on the infinst_autol.exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 2 – Install VGA Driver 1.
Multi-Touch Panel PC ACP-5187 Note 2: If the OS is Windows® XP, you have to install the driver of dotNet Framework first. Simply click on dotnetfx35.exe located in dotNet Framwork folder. Step 3 –Install LAN 1 Driver (Intel® LAN Chip) 1. Click on the STEP3-LAN1 folder and select the OS folder your system is 2. Double click on the .exe file located in each OS folder 3. Follow the instructions that the window shows 4.
Multi-Touch Panel PC ACP-5187 Step 6 – Install ME Driver 1. Click on the STEP6-ME SW folder and select the OS folder your system is 2. Double click on the Setup.exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 7 – Install RAID & AHCI Driver Please refer to the Appendix D RAID & AHCI Settings Step 8 – Install TPM Driver 1. Click on the STEP8-TPM folder and select the OS folder your system is 2.
Multi-Touch Panel PC ACP-5187 Step 10 –Install USB3.0 Driver 1. Click on the STEP10-USB3.0 folder and select the OS folder your system is 2. Double click on the Setup.exe file located in each OS folder 3. Follow the instructions that the window shows 4.
Multi-Touch Panel PC ACP-5187 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
Multi-Touch Panel PC ACP-5187 A.1 Programming ACP-5187 utilizes ITE IT8728F chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the ITE 8728F enters the normal mode with all logical devices disabled except KBC.
Multi-Touch Panel PC ACP-5187 There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode. Undesired result may occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state.
Multi-Touch Panel PC ACP-5187 WatchDog Timer Configuration Registers Configure Control (Index=02h) This register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them.
Multi-Touch Panel PC ACP-5187 WatchDog Timer Control Register (Index=71h, Default=00h) WatchDog Timer Configuration Register (Index=72h, Default=00h) WatchDog Timer Time-out Value Register (Index=73h, Default=00h) Appendix A Programming the Watchdog Timer A-5
Multi-Touch Panel PC ACP-5187 A.2 ITE8728F Watchdog Timer Initial Program .MODEL SMALL .CODE Main: CALL Enter_Configuration_mode CALL Check_Chip mov cl, 7 call Set_Logic_Device ;time setting mov cl, 10 ; 10 Sec dec al Watch_Dog_Setting: ;Timer setting mov al, cl mov cl, 73h call Superio_Set_Reg ;Clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call Superio_Set_Reg ;unit is second.
Multi-Touch Panel PC ACP-5187 ; game port enable mov cl, 9 call Set_Logic_Device Initial_OK: CALL Exit_Configuration_mode MOV AH,4Ch INT 21h Enter_Configuration_Mode PROC NEAR MOV SI,WORD PTR CS:[Offset Cfg_Port] MOV DX,02Eh MOV CX,04h Init_1: MOV AL,BYTE PTR CS:[SI] OUT DX,AL INC SI LOOP Init_1 RET Enter_Configuration_Mode ENDP Exit_Configuration_Mode PROC NEAR MOV AX,0202h CALL Write_Configuration_Data Appendix A Programming the Watchdog Timer A-7
Multi-Touch Panel PC ACP-5187 RET Exit_Configuration_Mode ENDP Check_Chip PROC NEAR MOV AL,20h CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MOV AL,21h CALL Read_Configuration_Data CMP AL,12h JNE Not_Initial Need_Initial: STC RET Not_Initial: CLC RET Check_Chip ENDP Read_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL Appendix A Programming the Watchdog Timer A-8
Multi-Touch Panel PC ACP-5187 MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Write_Configuration_Data ENDP Superio_Set_Reg proc near push ax MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret Superio_Set_Reg endp.
Multi-Touch Panel PC ACP-5187 push ax push cx xchg al,cl mov cl,07h call Superio_Set_Reg pop cx pop ax ret Set_Logic_Device endp ;Select 02Eh->Index Port, 02Fh->Data Port Cfg_Port DB 087h,001h,055h,055h DW 02Eh,02Fh END Main Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 . .
Multi-Touch Panel PC ACP-5187 Appendix B I/O Information Appendix B I/O Information B-1
Multi-Touch Panel PC B.
Multi-Touch Panel PC ACP-5187 Appendix B I/O Information B-3
Multi-Touch Panel PC B.
Multi-Touch Panel PC ACP-5187 B.3 IRQ Mapping Chart B.
Multi-Touch Panel PC ACP-5187 Appendix C Miscellanea Appendix C Miscellanea C-1
Multi-Touch Panel PC ACP-5187 C.1 General Cleaning Tips You may need the following precautions before you begin to clean the computer. When you clean any single part or component for the computer, please read and understand the details below fully. 1. Never spray or squirt the liquids directly onto any computer component. If you need to clean the device, please rub it with a piece of dry cloth. 2. Be cautious of the tiny removable components when you use a vacuum cleaner to absorb the dirt on the floor.
Multi-Touch Panel PC ACP-5187 C.2 Cleaning tools Although many companies have created products to help improve the process of cleaning your computer and peripherals users can also use household items to clean their computers and peripherals. Below is a listing of items you may need or want to use while cleaning your computer or computer peripherals.
Multi-Touch Panel PC ACP-5187 Cotton swabs - Cotton swaps moistened with rubbing alcohol or water are excellent tools for wiping hard to reach areas in your keyboard, mouse, and other locations. Foam swabs - Whenever possible it is better to use lint free swabs such as foam swabs. Note: We strongly recommended that you should shut down the system before you start to clean any single components. Please follow the steps below. 1. Close all application programs 2. Close operating software 3.
Multi-Touch Panel PC ACP-5187 C.3 Scrap Computer Recycling If the computer equipments need the maintenance or are beyond repair, we strongly recommended that you should inform us as soon as possible for the suitable solution. For the computers that are no longer useful or work well, please contact with worldwide distributors for recycling. The worldwide distributors show on the following website: http://www.aaeon.
Multi-Touch Panel PC ACP-5187 C.
Multi-Touch Panel PC ACP-5187 MSR Installation Step 1: Fasten the two screws (2-SELF TAPPING SCREWS) to fix the MSR Bracket with the ACP-5187 Appendix C Miscellanea C-7
Multi-Touch Panel PC ACP-5187 Bar Code Scanner Installation Step 1: Fasten the three screws to fix the Bar Code Scanner with the backet Appendix C Miscellanea C-8
Multi-Touch Panel PC ACP-5187 Step 2: Fasten the two screws (2-SELF TAPPING SCREWS) to fix the Bar Code Scanner with the ACP-5187 Appendix C Miscellanea C-9
Multi-Touch Panel PC ACP-5187 Appendix D RAID & AHCI Settings Appendix D RAID & AHCI Settings D-1
Multi-Touch Panel PC ACP-5187 D.1 Setting RAID OS installation to SETUP RAID Mode Step 1: Extract the f6fly-x86.zip from “Driver CD -> STEP7-RAID&AHCI\WinXP_32” and copy below files to diskette. Step 2: Connect the USB Floppy drive to the board and insert the diskette from previous step.
Multi-Touch Panel PC ACP-5187 Step 3: Configure SATA Controller to RAID mode in BIOS SETUP Menu: Advanced -> SATA Configuration -> SATA Mode -> RAID Mode Step 4: Configure DVD/CD-ROM drive as the first boot device.
Multi-Touch Panel PC ACP-5187 Step 5: Save changes and exit BIOS SETUP Step 6: Press CTRL-I to enter RAID Configuration Utility Appendix D RAID & AHCI Settings D-4
Multi-Touch Panel PC ACP-5187 Step 7: Choose “1.
Multi-Touch Panel PC ACP-5187 Step 9 – Choose “Create Volume” and confirmed in next warning message.
Multi-Touch Panel PC ACP-5187 Step 10 – Exit RAID Configuration Utility and Reboot to DVD/CD-ROM device to install OS Step 11 – Press “F6” to install RAID driver Step 12 – Press “S” to install RAID driver Appendix D RAID & AHCI Settings D-7
Multi-Touch Panel PC ACP-5187 Step 13 – Choose “Intel(R) Mobile Express Chipset SATA RAID Controller” Step 14 – It will show the model you selected and then press ”ENTER”. Windows Setup will continue to install OS.
Multi-Touch Panel PC ACP-5187 D.2 Setting AHCI OS installation to SETUP AHCI Mode Step 1: Extract the f6fly-x86.zip from “Driver CD -> STEP7 RAID&AHCI\WinXP_32” and copy below files to diskette. Step 2: Connect the USB Floppy drive to the board and insert the diskette from previous step.
Multi-Touch Panel PC ACP-5187 Step 3: Configure SATA Controller to RAID mode in BIOS SETUP Menu: Advanced -> SATA Configuration -> SATA Mode -> AHCI Mode Step 4: Configure DVD/CD-ROM drive as the first boot device.
Multi-Touch Panel PC ACP-5187 Step 5: Save changes and exit BIOS SETUP Step 6 – Boot to DVD/CD-ROM device to install OS Step 7 – Press “F6” to install AHCI driver Appendix D RAID & AHCI Settings D-11
Multi-Touch Panel PC ACP-5187 Step 8 – Press “S” to install AHCI driver Step 9 – Choose “Intel(R) 7 Series Chipset Family SATA AHCI Controller” Appendix D RAID & AHCI Settings D-12
Multi-Touch Panel PC ACP-5187 Step 10 – It will show the model you selected and then press ”ENTER”. Windows Setup will continue to install OS.
