Wallmount Chassis AEC-204 Chapter 2 Quick Installation Guide Notice: The Quick Installation Guide is derived from Chapter 2 of user manual. For other chapters and further installation instructions, please refer to the user manual CD-ROM that came with the product. Part No. 2007020403 Printed in Taiwan FEB.
Wallmount Chassis AEC-204 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
Wallmount Chassis AEC-204 2.2 FCC Statement This devise complies with part 15 FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received including interference that may cause undesired operations. This equipment has been tested and found to comply with the limits for a class "A" digital device, pursuant to part 15 of the FCC rules.
Wallmount Chassis AEC-204 2.3 Notice Dear Customer, Thank you for purchasing the AEC-204 wallmount chassis. This quick installation guide is designed to assist you. Please read it thoroughly before you install and use this chassis. The product that you have purchased comes with a two year limited warranty, however AAEON will not be responsible for misuse of the product. Therefore, we strongly urge you to read this installation guide before using the product.
Wallmount Chassis AEC-204 2.4 Power Connection The AEC-204 compact chassis offers a traditional power module with 150 watts of power. Situated in the bottom of the chassis in a enclosed housing, this power supply will limit the negative effects of electrical magnetic interference.
Wallmount Chassis 2.
Wallmount Chassis AEC-204 Step 3: Unscrew the bottom cover Step 4: Separate the bottom cover from the chassis Chapter 2 Quick Installation Guide 2-7
Wallmount Chassis AEC-204 2.6 Installing the power supply and backplanes The power supply is to be secured at the bottom of the chassis. The fan and power cord connection (in the rear of the power supply) should face the opening on the rear of the chassis Step 1: Fasten the two screws of the power supply to the Chassis Step 2: Fasten another two screws on the rear of the chassis to provide additional support.
Wallmount Chassis AEC-204 Step 3: Fasten the four copper pillars in the Chassis Step 4: Place the backplane to the Chassis and fasten the backplane with four screws Chapter 2 Quick Installation Guide 2-9
Wallmount Chassis AEC-204 Step 5: Pass the power cables through the hole in the bottom of the Chassis and then plug into the ATX connector ATX Connector Step 6: Screw the bottom of the Chassis with the four screws Chapter 2 Quick Installation Guide 2- 10
Wallmount Chassis AEC-204 2.7 Installing the Floppy Disk Drive and CD-ROM Step 1: Remove the bracket for the Module Step 2: Unscrew the module Step 3: Insert the CD-ROM/ FDD into the bracket and brace the CD-ROM/FDD unit with four screws.
Wallmount Chassis AEC-204 Step 4: Replace the whole unit back to the Chassis Step 5: You may choose the attached parallel port and serial port I/O connectors. Simply brace the connector to the specified slot location with the provided screws.
Wallmount Chassis AEC-204 2.8 Installing the Hard Disk Drive Step 1: Hold the HDD against the wall of the chassis, and insert four screws from the outside of the chassis to brace the module.
Wallmount Chassis AEC-204 2.9 Cable Connections Note: Each cable has a specific colored line designated for pin number 1 make sure these connections are carefully carried out. Hard drive cable connection Find the 40-pin and 44-pin header hard drive cable. Plug the 40-pin header and plug this end into the hard drive, and connect the 44pin header into CPU board. Floppy drive cable connection Find the 34-pin header floppy drive cable.
Wallmount Chassis AEC-204 2.
Wallmount Chassis AEC-204 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Boxer/ Industrial System 有毒有害物质或元素 部件名称 铅 汞 镉 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 硬盘 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 外壳 中央处理器 与内存 六价铬 多溴联苯 多溴二苯醚 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注： 一、此产品所标示之环保使用期限，系指在一般正常使用状况下。 二、上述部件物
