Embedded Controller AEC-6523 AEC-6523 Embedded Controller Intel® Atom™ N2600 Dual Core 1.6GHz Processor Dual LAN, 4 USB2.0, 4 COM, 1 VGA 1 Mini Card AEC-6523 Manual 1st Ed.
Embedded Controller AEC-6523 Copyright Notice This document is copyrighted, 2013. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Embedded Controller AEC-6523 Acknowledgments All other products’ name or trademarks are properties of their respective owners. • AMI is a trademark of American Megatrends, Inc. • CompactFlash™ is a trademark of the Compact Flash Association. • Microsoft Windows is a registered trademark of Microsoft Corp. • Intel®, Atom™ are trademarks of Intel Corporation. • PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation.
Embedded Controller AEC-6523 Packing List Before you begin operating your PC, please make sure that the following materials are enclosed: z 1 AEC-6523 Embedded Controller z 2 Wallmount Brackets z 1 Screw Package z 1 DVD-ROM for manual (in PDF format) and drivers z 1 Phoenix Power Connector z 1 Heat Spreader If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
Embedded Controller AEC-6523 Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a firm surface during installation.
Embedded Controller AEC-6523 d. The equipment does not work well, or you cannot get it to work according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20°C (-4°F) OR ABOVE 70°C (158°F). IT MAY DAMAGE THE EQUIPMENT. FCC This device complies with Part 15 FCC Rules.
Embedded Controller AEC-6523 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Boxer/ Industrial System 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 硬盘 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 外壳 中央处理器 与内存 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注： 一、此产品所标示之环保使用期限，系指在一般正常使用状况下。 二、上述
Embedded Controller Chapter 1 AEC-6523 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Hardware Installation 2.1 Dimension and I/O of AEC-6523............................... 2-2 2.2 Connectors and Jumpers of The Main Board ........... 2-3 2.3 List of Jumpers .........
Embedded Controller AEC-6523 Chapter 4 Driver Installation 4.1 Installation ................................................................. 4-3 Appendix A Programming The Watchdog Timer A.1 Programming ........................................................A-2 A.2 ITE8783 Watchdog Timer Initial Program ............A-6 Appendix B I/O Information B.1 I/O Address Map ..................................................B-2 B.2 1st MB Memory Address Map ...............................B-4 B.
Embedded Controller AEC-6523 Chapter 1 General Information Chapter 1 General Information 1- 1
Embedded Controller AEC-6523 1.1 Introduction AAEON introduces the newest product in the Boxer series, AEC-6523, which utilizes the Intel® Atom™ N2600 processor: this embedded controller expands its graphics performance greatly with the newest generation of Atom™ processors.
Embedded Controller AEC-6523 1.2 Features z Intel® AtomTM N2600 Dual Core 1.6GHz Processor z Intel® NM10 Express chipset z Intel® GMA 3600 Integrated Graphic Engine z USB2.0 x 4 z COM x 4 z Dual Gigabit Ethernet LAN z VGA Output z Fanless System Design z Wide DC power Input z Wide Operating Temperature Range: 1. With W/T HDD: (-25°C ~ 70°C) 2.
Embedded Controller AEC-6523 1.3 Specifications System z CPU Intel® AtomTM N2600 Dual Core 1.6GHz Processor z Memory DDR3 SODIMM x 1, supports DDR3 800/1066, Max. 2GB z VGA VGA x 1 z Ethernet Gigabit Ethernet, RJ-45 connector x 2 z Hard Disk Storage 2.5’ SATA 2 (3.
Embedded Controller AEC-6523 Mechanical and Environmental z Construction Rugged Aluminum Alloy Chassis z Color Dark Gray z Mounting Wall mount/VESA/DIN Rail z Dimension 8.35”(W) x 3.1”(H) x 2.25”(D) (212.15 mm x 78.88 mm x 107 mm) z Gross Weight 8.36 lb (3.8 kg) z Net Weight 4.75 lb (2.
Embedded Controller z EMC Chapter 1 General Information 1- 6 AEC-6523 CE/FCC Class A
Embedded Controller AEC-6523 Chapter 2 Hardware Installation Chapter 2 Hardware Installation 2-1
Embedded Controller AEC-6523 2.
Embedded Controller AEC-6523 2.
Embedded Controller Solder Side Chapter 2 Hardware Installation 2 - 4 AEC-6523
Embedded Controller AEC-6523 2.3 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
Embedded Controller AEC-6523 2.4 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
Embedded Controller CN25 Stereo-L Channel CN26 1st LVDS Inverter AEC-6523 CN27 1st LVDS (Single channel 18/24bit) CN28 2nd RJ-45 Ethernet CN29 1st RJ-45 Ethernet CN30 USB Port #1 and #2 CN31 Audio Line In/Out and MIC CN32 CRT/DVI (Configured by manufacturing) CN33 COM Port #1 CN34 SIM Card Socket CFD1 CFAST™ PCIE1 Mini Card/mSATA (Configured by manufacturing) DIMM1 DDR3 SODIMM Slot Chapter 2 Hardware Installation 2 - 7
Embedded Controller AEC-6523 2.5 Auto Power Button Selection (JP1) JP1 Function 1-2 Enable 2-3 Disable (Default) 2.6 Clear CMOS (JP2) JP2 Function 1-2 Normal (Default) 2-3 Clear CMOS 2.7 COM2 RI/+5V/+12V Selection (JP3) JP3 Function 1-2 +12V 3-4 RI (Default) 5-6 +5V 2.8 COM Port 1 Connector Pin Signal Pin Signal 1 DCDA 2 RXA 3 TXA 4 DTRA 5 Ground 6 DSRA 7 RTSA 8 CTSA 9 RIA 2.
Embedded Controller AEC-6523 RS-232 Mode Pin Signal Pin Signal 1 DCDB 2 RXB 3 TXB 4 DTRB 5 Ground 6 DSRB 7 RTSB 8 CTSB 9 RIB/+5V/(+12V) RS-422 Mode Pin Signal Pin Signal 1 TXD- 2 RXD+ 3 TXD+ 4 RXD- 5 Ground 6 N/C 7 N/C 8 N/C 9 N/C / +5V / (+12V) Pin Signal RS-485 Mode Pin Signal 1 TXD- 2 N/C 3 TXD+ 4 N/C 5 Ground 6 N/C 7 N/C 8 N/C 9 N/C / +5V / (+12V) 2.
Embedded Controller 9 AEC-6523 RIC 2.
Embedded Controller AEC-6523 2.12 Hard Disk Drive Installation Step 1: Open the bottom case of AEC-6523 by loosening the two screws. Step 2: Get the Hard Disk Drive ready.
Embedded Controller Step 3: Install the CFast™ card. Step 4: Fasten the cover of the CFast™ card.
Embedded Controller AEC-6523 Step 5: Stack the HDD and bracket. Fasten the HDD and bracket with the screws. Step 6: Connect the SATA and power cables to the HDD.
Embedded Controller AEC-6523 Step 7: Fasten the bracket of the HDD. Step 8: Fasten the bottom HDD kit case of AEC-6523.
Embedded Controller AEC-6523 2.13 SD RAM Installation Step 1: Loosen the bottom HDD kit of the AEC-6523. Step 2: Fasten the bottom case of the AEC-6523.
Embedded Controller AEC-6523 Step 3: Loosen the screw on the front panel of AEC-6523 Step 4: Loosen the screws on the rear panel of AEC-6523 Chapter 2 Hardware Installation 2 - 16
Embedded Controller AEC-6523 Step 5: Insert the SDRAM to the memory slot. Step 6: Press the SDRAM and make sure that it has been inserted properly.
Embedded Controller AEC-6523 Step 7: Adhere the heat-spreading sheet to the SDRAM. Step 8: Close the bottom case of AEC-6523 and fasten the four screws on the bottom case.
Embedded Controller AEC-6523 Step 8-1: Close the bottom HDD kit case of AEC-6523 and fasten the two screws on the bottom case. Step 9: Close the front case of AEC-6523 and fasten the screw on the front case.
Embedded Controller AEC-6523 Step 10: Close the rear case of AEC-6523 and fasten the two screws on the rear case.
Embedded Controller AEC-6523 2.14 DIN Rail Installation Step 1: Fix the DIN Rail kit with the screws on the chassis as shown below. Step 2: Press the DIN Rail on the DIN Rail kit to fix it.
Embedded Controller AEC-6523 2.15 Wallmount Installation Step 1: Fasten the brackets with the screws. We suggest using this screw.
Embedded Controller AEC-6523 Chapter 3 AMI BIOS Setup Chapter 3 Award BIOS Setup 3-1
SubCompact Board 3.1 AEC-6523 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. System configuration verification These routines check the current system configuration against the values stored in the CMOS memory.
SubCompact Board 3.2 AEC-6523 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
SubCompact Board AEC-6523 Setup submenu: Main Options summary: (default setting) System Date Day MM:DD:YYYY Change the month, year and century. The ‘Day’ is changed automatically. System Time HH : MM : SS Change the clock of the system.
SubCompact Board AEC-6523 Setup submenu: Advanced Options summary: (default setting) ACPI Settings System ACPI Parameters S5 RTC Wake Settings Enable system to wake from S5 using RTC alarm.
SubCompact Board USB Configuration Parameters Super IO Configuration System Super IO Chip Parameters H/W Monitor Monitor hardware status Chapter 3 AMI BIOS Setup 3-6 AEC-6523
SubCompact Board AEC-6523 ACPI Settings Options summary: (default setting) Suspend Disabled ACPI Sleep State S1 only(CPU Stop Clock) S3 only(Suspend to RAM) Select the ACPI state used for System Suspend Chapter 3 Award BIOS Setup 3-7
SubCompact Board AEC-6523 RTC Wake Settings Options summary: (default setting) Wake system with Fixed Disabled Time Enabled Enable or disable System wake on alarm event. Wake up time is setting by following settings.
SubCompact Board Wake system with Disabled Dynamic Time Enabled AEC-6523 Enable or disable System wake on alarm event. Wake up time is current time + Increase minutes.
SubCompact Board CPU Configuration Options summary: (default setting) Hyper-Threading Disabled Enabled En/Disable CPU Hyper-Threading function Chapter 3 AMI BIOS Setup 3-10 AEC-6523
SubCompact Board AEC-6523 SATA Configuration (IDE) Options summary: (default setting) SATA Controller(s) Disabled Enabled En/Disable SATA controller Configure SATA as IDE AHCI Configure SATA controller operating as IDE/AHCI mode.
SubCompact Board AEC-6523 SATA Configuration (AHCI) Options summary: (default setting) SATA Controller(s) Disabled Enabled En/Disable SATA controller Configure SATA as IDE AHCI Configure SATA controller operating as IDE/AHCI mode.
SubCompact Board AEC-6523 En/Disable the selected port. SATA Port 0/Port 1 Hot Plug Disabled Enabled En/Disable Hot Plug feature for specified port.
SubCompact Board AEC-6523 USB Configuration Options summary: (default setting) Legacy USB Support Enabled Disabled Auto Enables BIOS Support for Legacy USB Support. When enabled, USB can be functional in legacy environment like DOS. AUTO option disables legacy support if no USB devices are connected.
SubCompact Board AEC-6523 Forced FDD Hard Disk CD-ROM If Auto. USB devices less than 530MB will be emulated as Floppy and remaining as Floppy and remaining as hard drive. Forced FDD option can be used to force a HDD formatted drive to boot as FDD(Ex.
SubCompact Board AEC-6523 Super IO Configuration Options summary: (default setting) Serial Port 1/2/3/4 Configuration Set Parameters of Serial Port 1/2/3/4 Restore AC Power Loss Power Off Power On Last State Select AC power state when power is re-applied after a power failure.
SubCompact Board AEC-6523 Serial Port 1 Configuration Options summary: (default setting) Serial Port Disabled Enabled En/Disable specified serial port. Change Settings Auto IO=3F8h; IRQ=4; IO=3F8h; IRQ=3,4,5,7,10,11,12; IO=2F8h; IRQ=3,4,5,7,10,11,12; IO=3E8h; IRQ=3,4,5,7,10,11,12; IO=2E8h; IRQ=3,4,5,7,10,11,12; Select a resource setting for Super IO device.
SubCompact Board AEC-6523 Serial Port 2 Configuration Options summary: (default setting) Serial Port Disabled Enabled En/Disable specified serial port.
SubCompact Board AEC-6523 Select a resource setting for Super IO device. COM2 Type Select RS232 RS422 RS485 Configure COM2 operated as RS232, RS422 or RS485.
SubCompact Board AEC-6523 Serial Port 3 Configuration Options summary: (default setting) Serial Port Disabled Enabled En/Disable specified serial port. Change Settings Auto IO=3E8h; IRQ=10; IO=3F8h; IRQ=3,4,5,6,7,9,10,11,12; IO=2F8h; IRQ=3,4,5,6,7,9,10,11,12; IO=3E8h; IRQ=3,4,5,6,7,9,10,11,12; IO=2E8h; IRQ=3,4,5,6,7,9,10,11,12; Select a resource setting for Super IO device.
SubCompact Board AEC-6523 Serial Port 4 Configuration Options summary: (default setting) Serial Port Disabled Enabled En/Disable specified serial port. Change Settings Auto IO=2E8h; IRQ=11; IO=3F8h; IRQ=3,4,5,6,7,9,10,11,12; IO=2F8h; IRQ=3,4,5,6,7,9,10,11,12; IO=3E8h; IRQ=3,4,5,6,7,9,10,11,12; IO=2E8h; IRQ=3,4,5,6,7,9,10,11,12; Select a resource setting for Super IO device.
SubCompact Board H/W Monitor Chapter 3 AMI BIOS Setup 3-22 AEC-6523
SubCompact Board AEC-6523 Setup submenu: Chipset Options summary: (default setting) Host Bridge Host Bridge Parameters South Bridge South Bridge Parameters Chapter 3 Award BIOS Setup 3-23
SubCompact Board Host Bridge Options summary: (default setting) Intel IGD Configuration Configure Intel IGD Settings.
SubCompact Board AEC-6523 Intel IGD Configuration Options summary: (default setting) Auto Disable IGD Enabled Disabled Select Primary boot display device IGFX – Boot Type CRT Select Primary boot display device Fixed Graphics Memory Size 128MB 256MB Configure Fixed Graphics Memory Size Chapter 3 Award BIOS Setup 3-25
SubCompact Board South Bridge Options summary: (default setting) Power Mode ATX Type AT Type Select the power type used on the system TPT Devices HD audio and onboard LAN Settings. PCIe mini-Card Slot PCIe mini-Card Slot Settings.
SubCompact Board AEC-6523 TPT Devices Options summary: (default setting) Azalia Controller Disabled HD Audio Enable or disabled Azalia controller R8111E #1 Controller Disabled Enabled Enable or disable PCIE Lan. R8111E #2 Controller Disabled Enabled Enable or disable PCIE Lan.
SubCompact Board Setup submenu: Boot Options summary: (default setting) Quiet Boot Disabled Enabled En/Disable showing boot logo. Launch RTL8111E PXE Disabled OpROM Enabled En/Disable PXE boot for RTL8111E LAN Boot Option #X/ XXXX Drive BBS Priorities The order of boot priorities.
SubCompact Board AEC-6523 BBS Priorities Options summary: (default setting) Boot Option #x Disabled Device name Sets the system boot order Chapter 3 Award BIOS Setup 3-29
SubCompact Board Setup submenu: Security Options summary: (default setting) Administrator Password/ Not set User Password Chapter 3 AMI BIOS Setup 3-30 AEC-6523
SubCompact Board AEC-6523 You can install a Supervisor password, and if you install a supervisor password, you can then install a user password. A user password does not provide access to many of the features in the Setup utility. Install the Password: Press Enter on this item, a dialog box appears which lets you enter a password. You can enter no more than six letters or numbers. Press Enter after you have typed in the password. A second dialog box asks you to retype the password for confirmation.
SubCompact Board HDD Security Options summary: (default setting) Set User Password/ Not set Set Master Password Chapter 3 AMI BIOS Setup 3-32 AEC-6523
SubCompact Board AEC-6523 You can install a Master and User password. Before booting to OS, HDD will be set to frozen state. On S3 resume HDD will be unlocked using the HDD Password we entered while system booting. Install the Password: Press Enter on this item, a dialog box appears which lets you enter a password. You can enter no more than six letters or numbers. Press Enter after you have typed in the password. A second dialog box asks you to retype the password for confirmation.
SubCompact Board AEC-6523 Setup submenu: Exit Options summary: (default setting) Save Changes and Reset Reset the system after saving the changes Discard Changes and Reset Reset system setup without saving any changes Restore Defaults Restore/Load Default values for all the setup options.
Embedded Controller AEC-6523 Chapter 4 Driver Installation Chapter 4 Driver Installation 4 - 1
Embedded Controller AEC-6523 The AEC-6523 comes with a DVD-ROM that contains all drivers and utilities that meet your needs.
Embedded Controller AEC-6523 4.1 Installation: Insert the AEC-6523 DVD-ROM into the DVD-ROM drive, and then install the drivers from Step 1 to Step 6 in order. Step 1 – Install Chipset Driver 1. Click on the STEP1-CHIPSET folder and select the OS folder your system is 2. Double click on the infinst_autol.exe located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 2 – Install VGA Driver For Windows® 7 1.
Embedded Controller AEC-6523 Step 3 – Install LAN Driver 1. Click on the STEP3-LAN folder and select the OS folder your system is 2. Double click on the Setup.exe located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 4 – Install Audio Driver 1. Click on the STEP4-Audio folder and select the OS folder your system is 2. Double click on the Setup.exe located in each OS folder 3.
Embedded Controller AEC-6523 located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Note: If the OS is Chinese version, you may click on Serial Patch v1.0.1. exe file located in each OS folder.
Embedded Controller AEC-6523 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
Embedded Controller AEC-6523 A.1 Programming AEC-6523 utilizes the ITE 8783 chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON initial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the ITE 8783 enters the normal mode with all logical devices disabled except KBC.
Embedded Controller AEC-6523 Exit the MB PnP Mode. Undesired result may occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state. To ensure the initial state of the key-check logic, it is necessary to perform four write opera-tions to the Special Address port (2EH). Two different enter keys are provided to select configuration ports (2Eh/2Fh) of the next step.
Embedded Controller AEC-6523 Configure Control (Index=02h) This register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them.
Embedded Controller AEC-6523 82h, 92h Default=001s0000b) Watch Dog Timer 1,2,3 Time-Out Value (LSB) Register (Index=73h,83h,93h, Default=38h) Watch Dog Timer 1,2,3 Time-Out Value (MSB) Register (Index=74h,84h,94h Default=00h) Appendix A Programming the Watchdog Timer A-5
Embedded Controller AEC-6523 A.2 ITE8783 Watchdog Timer Initial Program .MODEL SMALL .CODE Main: CALL Enter_Configuration_mode CALL Check_Chip mov cl, 7 call Set_Logic_Device ;time setting mov cl, 10 ; 10 Sec dec al Watch_Dog_Setting: ;Timer setting mov al, cl mov cl, 73h call Superio_Set_Reg ;Clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call Superio_Set_Reg ;unit is second.
Embedded Controller AEC-6523 call Superio_Set_Reg ; game port enable mov cl, 9 call Set_Logic_Device Initial_OK: CALL Exit_Configuration_mode MOV AH,4Ch INT 21h Enter_Configuration_Mode PROC NEAR MOV SI,WORD PTR CS:[Offset Cfg_Port] MOV DX,02Eh MOV CX,04h Init_1: MOV AL,BYTE PTR CS:[SI] OUT DX,AL INC SI LOOP Init_1 RET Enter_Configuration_Mode ENDP Exit_Configuration_Mode PROC NEAR MOV AX,0202h Appendix A Programming the Watchdog Timer A-7
Embedded Controller CALL Write_Configuration_Data RET Exit_Configuration_Mode ENDP Check_Chip PROC NEAR MOV AL,20h CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MOV AL,21h CALL Read_Configuration_Data CMP AL,81h JNE Not_Initial Need_Initial: STC RET Not_Initial: CLC RET Check_Chip ENDP Read_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] Appendix A Programming the Watchdog Timer A-8 AEC-6523
Embedded Controller AEC-6523 OUT DX,AL MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Write_Configuration_Data ENDP Superio_Set_Reg proc near push ax MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret Superio_Set_Reg endp.
Embedded Controller Set_Logic_Device proc AEC-6523 near push ax push cx xchg al,cl mov cl,07h call Superio_Set_Reg pop cx pop ax ret Set_Logic_Device endp ;Select 02Eh->Index Port, 02Fh->Data Port Cfg_Port DB 087h,001h,055h,055h DW 02Eh,02Fh END Main Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 . .
Embedded Controller AEC-6523 Appendix B I/O Information Appendix B I/O Information B - 1
Embedded Controller B.
Embedded Controller AEC-6523 Appendix B I/O Information B - 3
Embedded Controller B.
Embedded Controller AEC-6523 B.
Embedded Controller B.
Embedded Controller AEC-6523 Appendix C AHCI Setting Appendix C AHCI Setting C-1
Embedded Controller AEC-6523 C.1 Setting AHCI OS installation to setup AHCI Mode. Step 1: Copy the files below from “Driver CD -> STEP5-AHCI\WINXP_32\F6 Install Floppy for Windows” to Floppy Disk.
Embedded Controller AEC-6523 Step 3: Press “F6” Step 4: Choose “S” Appendix C AHCI Setting C-3
Embedded Controller AEC-6523 Step 5: Choose “Intel® NM10 Express Chipset” Step 6: It will show the model number you select and then press “ENTER Step 7: Setup is loading files Appendix C AHCI Setting C-4
