Embedded Controller AEC-6611 AEC-6611 Compact Embedded Controller Intel® Atom™ N270 1.6GHz Processor Dual LAN, 2 USB2.0, 4 COM, 1 VGA AEC-6611 Manual 2nd Ed.
Embedded Controller AEC-6611 Copyright Notice This document is copyrighted, 2011. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Embedded Controller AEC-6611 Acknowledgments All other products’ name or trademarks are properties of their respective owners. • Award is a trademark of Award Software International, Inc. • CompactFlash™ is a trademark of the Compact Flash Association. • Microsoft Windows is a registered trademark of Microsoft Corp. • Intel®, Atom™ are trademarks of Intel Corporation. • PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation.
Embedded Controller AEC-6611 Packing List Before you begin operating your PC, please make sure that the following materials are enclosed: z 1 AEC-6611 Embedded Controller z 2 Wallmount Brackets z 1 Screw Package z 1 CD-ROM for manual (in PDF format) and drivers If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
Embedded Controller AEC-6611 Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a firm surface during installation.
Embedded Controller AEC-6611 d. The equipment does not work well, or you cannot get it to work according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20°C (-4°F) OR ABOVE 55°C (131°F). IT MAY DAMAGE THE EQUIPMENT. FCC This device complies with Part 15 FCC Rules.
Embedded Controller AEC-6611 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Boxer/ Industrial System 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 硬盘 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 外壳 中央处理器 与内存 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注： 一、此产品所标示之环保使用期限，系指在一般正常使用状况下。 二、上述
Embedded Controller Chapter 1 AEC-6611 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Hardware Installation 2.1 Dimension and I/O of AEC-6611............................... 2-2 2.2 Location of Connectors and Jumpers of the Main Board .................................
Embedded Controller AEC-6611 Chapter 1 General Information Chapter 1 General Information 1- 1
Embedded Controller AEC-6611 1.1 Introduction The newest Boxer series AEC-6611 has been introduced by AAEON and it utilizes Intel® Atom™ processor. In this era of information explosion, the advertising of consumer products will not be confined to the family television, but will also spread to high-traffic public areas, like department stores, the bus, transportation station, the supermarket etc.
Embedded Controller AEC-6611 1.2 Features z Intel® AtomTM N270 1.
Embedded Controller AEC-6611 1.3 Specifications System z CPU Intel® AtomTM N270 1.6GHz Processor z Memory DDR2 400/533 SODIMM x 1, Max. 2GB z VGA D-sub 15P VGA Connector z Ethernet 10/100/1000Base-TX Ethernet RJ-45 connector x 2 z Hard Disk Drive 2.5” SATA HDD x 1 z Expansion Mini-PCI x 1, Mini Card x 1 z Solid Storage Internal Type II CompactFlashTM slot Disk x1 Serial Port RS-232/422/485 x 1, RS-232 x 3 (x 8 z optional) z USB USB 2.
Embedded Controller AEC-6611 z Gross Weight 8.36 lb (3.8 kg) z Operating 5°F ~ 122°F (-20°C ~ 50°C) (CFD) Temperature 5°F ~ 131°F (-20°C ~ 55°C) (HDD) Storage -4°F ~ 158°F (-20°C ~ 70°C) z Temperature z Operating 5 ~ 90% @ 40°C, non-condensing Humidity z Vibration 5G rms/ 5~500Hz/ random operation –CFD 1G rms/ 5~500Hz/ random operation –HDD z Shock 50G peak acceleration (11msec. duration) –CFD 20G peak acceleration (11msec.
Embedded Controller AEC-6611 Chapter 2 Hardware Installation Chapter 2 Hardware Installation 2-1
Embedded Controller AEC-6611 2.
Embedded Controller AEC-6611 2.
Embedded Controller AEC-6611 Solder Side DIMM1 CN32 CFD1 Chapter 2 Hardware Installation 2 - 4
Embedded Controller AEC-6611 2.3 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
Embedded Controller AEC-6611 2.4 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
Embedded Controller AEC-6611 CN19 Keyboard / Mouse Connector CN20 SATA 1 Connector CN21 +12V Power Input Connector CN22 RJ-45 Ethernet#1 Connector CN23 RJ-45 Ethernet#2 Connector CN24 USB Port 5&6 Connector CN25 +5V Standby Power Output w/ PS_ON# & SMBus CN26 Audio In/Out/CD-in and MIC Connector CN27 +5V Output Connector for 2.
Embedded Controller AEC-6611 2.
Embedded Controller AEC-6611 Step 3: Fasten the four HDD screws and cover with the four black damper Black Damper Black Damper Chapter 2 Hardware Installation 2 - 9
Embedded Controller Step 4: Assembly the HDD chassis Step 5: Assembly the damper bracket Chapter 2 Hardware Installation 2 - 10 AEC-6611
Embedded Controller AEC-6611 Step 6: Connect the HDD cable Step 7: Fasten the four screws on the bottom lid of AEC-6611 Chapter 2 Hardware Installation 2 - 11
Embedded Controller AEC-6611 Step 8: Fasten the two screws on the front and rear panel USB LAN1 LAN2 SYS HDD DC IN 12V COM6 COM1 VGA COM7 COM2 COM3 COM4 COM5 COM8 Chapter 2 Hardware Installation 2 - 12
Embedded Controller AEC-6611 2.
Embedded Controller AEC-6611 Step 3: Insert the RAM at 30-degree angle to the memory slot and press Step 4: Close the bottom case of AEC-6611 and faten the four screws of the bottom lid Chapter 2 Hardware Installation 2 - 14
Embedded Controller AEC-6611 Step 5: Fasten the screws on the front and rear panel USB LAN1 LAN2 SYS HDD DC IN 12V COM6 COM1 VGA COM7 COM2 COM3 COM4 COM5 COM8 Chapter 2 Hardware Installation 2 - 15
Embedded Controller AEC-6611 2.7 Wallmount Kit Installation Get the brackets ready and fasten appropriate four screws on each bracket. After fastening the two brackets on the bottom lid of AEC-6611, the wallmount kit installation has been finished.
Embedded Controller AEC-6611 2.
Embedded Controller AEC-6611 Chapter 3 Award BIOS Setup Chapter 3 Award BIOS Setup 3-1
Embedded Controller 3.1 AEC-6611 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
Embedded Controller 3.2 AEC-6611 Award BIOS Setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press immediately. This will allow you to enter Setup. Standard CMOS Features Use this menu for basic system configuration. (Date, time, IDE, etc.
Embedded Controller AEC-6611 PnP/PCI Configurations This entry appears if your system supports PnP/PCI. PC Health Status Use this menu to set PC Health Status. Frequency/Voltage Control Use this menu to specify your settings for auto detect DIMM/PCI clock and spread spectrum. Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performance system operations.
Embedded Controller AEC-6611 Chapter 4 Driver Installation Chapter 4 Driver Installation 4 - 1
Embedded Controller AEC-6611 The AEC-6611 comes with a CD-ROM that contains all drivers and utilities that meet your needs.
Embedded Controller AEC-6611 4.1 Installation: Insert the AEC-6611 CD-ROM into the CD-ROM Drive. And install the drivers from Step 1 to Step 4 in order. Step 1 – Install INF Driver 1. Click on the STEP1-CHIPSET folder and double click on the infinst911_autol.exe 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 2 – Install VGA Driver 1. Click on the STEP2-VGA folder and select the OS folder your system is 2. Double click on the .
Embedded Controller AEC-6611 Once the card is installed and the computer is restarted, Windows will detect the board and attempt to load the drivers for it. 1. Windows will detect a “PCI Serial Port”. Select “Install from a list or specific location (Advanced)” as the shown of figure 1 and then click “Next.” Figure 1 2. Select “Search for the best driver in these locations.
Embedded Controller 3. AEC-6611 Windows has found an updated driver for this device as shown in figure 3 and then click “Next.” Figure 3 4. The “Completing the Found New Hardware Wizard” dialog. Appears as shown in figure 3, and then click “Finish.” 5. Repeat the above process for the second, third, fourth, and fifth AAEON PCI Communications Port. 6. Please re-start your Windows.
Embedded Controller AEC-6611 4-port Mini PCI module will show 4 AAEON PCI Communications Port and 2-port Mini PCI module will show 2 AAEON PCI Communications Port as the figure 4 shows 4 ports Mini PCI module Figure 4 Mini-PCI RS-232 module set up in Linux If the module is a 4-port Mini PCI module, you don’t need to proceed with the set up process, you can use it directly. For 2-port Mini PCI module, please use the following sequences to set up the module. 1.
Embedded Controller AEC-6611 2. Make lspci -v command to find OXmPCI952 IRQ and I/O address As the screen showing, we can find “Serial controller: Oxford Semiconductor Ltd:” this alphabetic string and then we will see the next line with IRQ number and the next with I/O address 3. Open the file: /etc/rc.
Embedded Controller Chapter 4 Driver Installation 4 - 8 AEC-6611
Embedded Controller AEC-6611 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
Embedded Controller AEC-6611 A.1 Programming AEC-6611 utilizes ITE 8781 chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON initial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the ITE 8781 enters the normal mode with all logical devices disabled except KBC.
Embedded Controller AEC-6611 There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode. Undesired result may occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state.
Embedded Controller AEC-6611 WatchDog Timer Configuration Registers Configure Control (Index=02h) This register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them.
Embedded Controller AEC-6611 Watch Dog Timer 1, 2, 3 Configuration Register (Index=72h, 82h, 92h Default=001s0000b) Watch Dog Timer 1,2,3 Time-Out Value (LSB) Register (Index=73h,83h,93h, Default=38h) Watch Dog Timer 1,2,3 Time-Out Value (MSB) Register (Index=74h,84h,94h Default=00h) Appendix A Programming the Watchdog Timer A-5
Embedded Controller AEC-6611 A.2 ITE8781 Watchdog Timer Initial Program .MODEL SMALL .CODE Main: CALL Enter_Configuration_mode CALL Check_Chip mov cl, 7 call Set_Logic_Device ;time setting mov cl, 10 ; 10 Sec dec al Watch_Dog_Setting: ;Timer setting mov al, cl mov cl, 73h call Superio_Set_Reg ;Clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call Superio_Set_Reg ;unit is second.
Embedded Controller AEC-6611 call Superio_Set_Reg ; game port enable mov cl, 9 call Set_Logic_Device Initial_OK: CALL Exit_Configuration_mode MOV AH,4Ch INT 21h Enter_Configuration_Mode PROC NEAR MOV SI,WORD PTR CS:[Offset Cfg_Port] MOV DX,02Eh MOV CX,04h Init_1: MOV AL,BYTE PTR CS:[SI] OUT DX,AL INC SI LOOP Init_1 RET Enter_Configuration_Mode ENDP Exit_Configuration_Mode PROC NEAR MOV AX,0202h Appendix A Programming the Watchdog Timer A-7
Embedded Controller CALL Write_Configuration_Data RET Exit_Configuration_Mode ENDP Check_Chip PROC NEAR MOV AL,20h CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MOV AL,21h CALL Read_Configuration_Data CMP AL,81h JNE Not_Initial Need_Initial: STC RET Not_Initial: CLC RET Check_Chip ENDP Read_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] Appendix A Programming the Watchdog Timer A-8 AEC-6611
Embedded Controller AEC-6611 OUT DX,AL MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Write_Configuration_Data ENDP Superio_Set_Reg proc near push ax MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret Superio_Set_Reg endp.
Embedded Controller Set_Logic_Device proc AEC-6611 near push ax push cx xchg al,cl mov cl,07h call Superio_Set_Reg pop cx pop ax ret Set_Logic_Device endp ;Select 02Eh->Index Port, 02Fh->Data Port Cfg_Port DB 087h,001h,055h,055h DW 02Eh,02Fh END Main Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 . .
