Embedded Controller AEC-6612 AEC-6612 Compact Embedded Controller Intel® Atom™ D510 1.66GHz Processor Dual LAN, 2/6 USB2.0, 2/6 COM, 1 VGA 2 PCI-Express Mini Card AEC-6612 Manual 2nd Ed.
Embedded Controller AEC-6612 Copyright Notice This document is copyrighted, 2011. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Embedded Controller AEC-6612 Acknowledgments All other products’ name or trademarks are properties of their respective owners. AMI is a trademark of American Megatrends Inc. CompactFlash™ is a trademark of the Compact Flash Association. Microsoft Windows is a registered trademark of Microsoft Corp. Intel®, Atom™ are trademarks of Intel Corporation. PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation.
Embedded Controller AEC-6612 Packing List Before you begin operating your PC, please make sure that the following materials are enclosed: 1 AEC-6612 Embedded Controller 2 Wallmount Brackets 1 Screw Package 1 CD-ROM for manual (in PDF format) and drivers If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
Embedded Controller AEC-6612 Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a firm surface during installation.
Embedded Controller AEC-6612 d. The equipment does not work well, or you cannot get it to work according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20°C (-4°F) OR ABOVE 55°C (131°F). IT MAY DAMAGE THE EQUIPMENT. FCC This device complies with Part 15 FCC Rules.
Embedded Controller AEC-6612 ENERGY STAR This Product has been certified by ENERGY STAR® The Regulation of ENERGY STAR®: ENERGY STAR® Requirements for Computer Version 5.2. The Test Standard of ENERGY STAR®: IEC/EN 62301, ENERGY STAR® Program Requirements for Computer Version ENERGY STAR® Compliance: Power Management features (Basic) Using power-saving states The system provides the two power-saving states: Sleep and Hibernation. When Sleep is initiated, the power lights blink and the screen clears.
Embedded Controller AEC-6612 Initiating and exiting Sleep The system set the Sleep mode after 30 minutes of inactivity when running on external power. You can change to none Sleep mode if the system needs to be active at all time. The default power management settings have been selected for compliance with ENERGY STAR®, and are recommended by the ENERGY STAR® program for optimal energy savings.
Embedded Controller AEC-6612 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Boxer/ Industrial System 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 硬盘 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 外壳 中央处理器 与内存 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注： 一、此产品所标示之环保使用期限，系指在一般正常使用状况下。 二、上述
Embedded Controller Chapter 1 AEC-6612 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Hardware Installation 2.1 Dimension and I/O of AEC-6612............................... 2-2 2.2 Location of Connectors and Jumpers of the Main Board .................................
Embedded Controller AEC-6612 Chapter 1 General Information Chapter 1 General Information 1- 1
Embedded Controller AEC-6612 1.1 Introduction The newest Boxer series AEC-6612 has been introduced by AAEON and it utilizes Intel® Atom™ processor. In this era of information explosion, the advertising of consumer products will not be confined to the family television, but will also spread to high-traffic public areas, like department stores, the bus, transportation station, the supermarket etc.
Embedded Controller AEC-6612 1.2 Features z Intel® AtomTM D510 1.
Embedded Controller AEC-6612 1.3 Specifications System z CPU Intel® AtomTM D510 1.66 GHz Processor z Memory DDR2 400/533 SODIMM x 1, Max. 2 GB z VGA VGA x 1 z Keyboard/Mouse Keyboard & Mouse by USB z Ethernet z Hard Disk Storage 2.
Embedded Controller AEC-6612 Mechanical and Environmental z Construction Aluminum Alloy Chassis z Color Dark Gray z Mounting Wallmount z Dimension 7.8”(W) x 2.3”(H) x 4.3”(D) (197 mm x 57.2 mm x 110 mm) z Net Weight 2.73 lb (1.24 kg) z Gross Weight 4.31 lb (1.
Embedded Controller AEC-6612 Chapter 2 Hardware Installation Chapter 2 Hardware Installation 2-1
Embedded Controller AEC-6612 2.
Embedded Controller AEC-6612 2.
Embedded Controller Solder Side Chapter 2 Hardware Installation 2 - 4 AEC-6612
Embedded Controller AEC-6612 2.3 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
Embedded Controller AEC-6612 2.4 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
Embedded Controller AEC-6612 CN20 USB Port #3 CN21 COM Port #3 CN22 COM Port #2 CN23 Audio Line In/Out and MIC Connector CN24 RJ-45 Ethernet #2 CN25 RJ-45 Ethernet #1 CN26 Digital I/O CN27 Parallel Port CN28 LVDS Inverter/ Backlight Connector CN29 18-bit LVDS Output CN30 USB Port #1 and #2 CN31 PS/2 Keyboard & Mouse CN32 COM Port #1 CN33 Analog CRT Display CN34 SIM Card Socket CFD1 Compact Flash Disk PCIE1 Mini-Card Slot #1 PCIE2 Mini-Card Slot #2 DIMM1 DDR2 SODIMM Slo
Embedded Controller AEC-6612 2.
Embedded Controller AEC-6612 Step 3: Fasten the four HDD screws and cover with the four black damper Black Damper Black Damper Chapter 2 Hardware Installation 2 - 9
Embedded Controller Step 4: Assembly the HDD chassis Step 5: Assembly the damper bracket Chapter 2 Hardware Installation 2 - 10 AEC-6612
Embedded Controller AEC-6612 Step 6: Connect the HDD cable Step 7: Fasten the four screws on the bottom lid of AEC-6612 Chapter 2 Hardware Installation 2 - 11
Embedded Controller AEC-6612 Step 8: Fasten the two screws on the front and rear panel USB LAN1 LAN2 SYS HDD DC IN 12V 510 COM1 VGA USB COM2 COM3 COM4 COM5 USB Chapter 2 Hardware Installation 2 - 12 COM6
Embedded Controller AEC-6612 2.
Embedded Controller AEC-6612 Step 3: Insert the RAM at 30-degree angle to the memory slot and press Step 4: Close the bottom case of AEC-6612 and faten the four screws of the bottom lid Chapter 2 Hardware Installation 2 - 14
Embedded Controller AEC-6612 Step 5: Fasten the screws on the front and rear panel USB LAN1 LAN2 SYS HDD DC IN 12V 510 COM1 COM6 VGA USB COM2 COM3 COM4 COM5 USB Chapter 2 Hardware Installation 2 - 15
Embedded Controller AEC-6612 2.7 Wallmount Kit Installation Get the brackets ready and fasten appropriate four screws on each bracket. After fastening the two brackets on the bottom lid of AEC-6612, the wallmount kit installation has been finished.
Embedded Controller AEC-6612 2.
Embedded Controller AEC-6612 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
Embedded Controller 3.1 AEC-6612 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. System configuration verification These routines check the current system configuration against the values stored in the CMOS memory.
Embedded Controller 3.2 AEC-6612 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
Embedded Controller AEC-6612 Chapter 4 Driver Installation Chapter 4 Driver Installation 4 - 1
Embedded Controller AEC-6612 The AEC-6612 comes with a CD-ROM that contains all drivers and utilities that meet your needs.
Embedded Controller AEC-6612 4.1 Installation: Insert the AEC-6612 CD-ROM into the CD-ROM Drive. And install the drivers from Step 1 to Step 4 in order. Step 1 – Install Chipset Driver 1. Click on the STEP1-CHIPSET folder and select the OS folder your system is 2. Double click on the infinst_autol.exe located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 2 – Install VGA Driver 1.
Embedded Controller AEC-6612 Step 4 – Install LAN Driver 1. Click on the STEP4-LAN folder and select the OS folder your system is 2. Double click on the PROWin32.exe located in each OS folder 3. Follow the instructions that the window shows 4.
Embedded Controller AEC-6612 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
Embedded Controller AEC-6612 A.1 Programming AEC-6612 utilizes W83627DHG-P chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application.
Embedded Controller AEC-6612 (3) Exit the W83627DHG config Mode. Undesired result may occur if the config Mode is not exited normally. (1) Enter the W83627DHG config Mode To enter the W83627DHG config Mode, two special I/O write operations are to be performed during Wait for Key state. To ensure the initial state of the key-check logic, it is necessary to perform two write operations to the Special Address port (2EH).
Embedded Controller = 010 AEC-6612 Power LED pin is driven low. = 011 Power LED pin outputs 2Hz pulse with 50% duty cycle. = 100 Power LED pin outputs 1Hz pulse with 50% duty cycle. = 101 Power LED pin outputs 4Hz pulse with 50% duty cycle. = 110 Power LED pin outputs 0.25Hz pulse with 50% duty cycle. =111 Power LED pin outputs 0.25Hz pulse with 50% duty cycle.. Bit 4 Bit 3 Bit 2 : WDTO# count mode is 1000 times faster. =0 Disable. =1 Enable. : select WDTO# count mode.
Embedded Controller AEC-6612 WatchDog Timer Register II (Index=F6h, Default=00h) Bit 7-0 = 0 x 00 Time-out Disable = 0 x 01 Time-out occurs after 1 second/minute = 0 x 02 Time-out occurs after 2 second/minutes = 0 x 03 Time-out occurs after 3 second/minutes ………………………………..
Embedded Controller =1 AEC-6612 Force Watchdog Timer time-out event: this bit is self-clearing Bit 4 Bit 3-0 : Watchdog Timer Status. R/W =1 Watchdog Timer time-out occurred =0 Watchdog Timer counting : These bits select IRQ resource for Watchdog. Setting of 2 selects SMI.
Embedded Controller AEC-6612 A.2 W83627DHG Watchdog Timer Initial Program Example: Setting 10 sec.
Embedded Controller AEC-6612 ;/////////////////////////////////////////////////////////////////////////////////////////////// Dec dx Mov al,0f5h ;CRF5 (PLED mode register) Out dx,al Inc dx In al,dx And al,not 08h ;Set second as counting unit Out dx,al ;/////////////////////////////////////////////////////////////////////////////////////////////// Dec dx Mov al,0f6h ; CRF6 Out dx,al Inc dx Mov al,10 ;Set timeout interval as 10 sec.
