Embedded Controller AEC-6635 AEC-6635 Fanless Embedded Controller Intel® Core™ i7/i5 Processor 2 Gigabit Ethernet, 6 USB, 4 COM 1 VGA, 1 DVI-D AEC-6635 Manual 2nd Ed.
Embedded Controller AEC-6635 Copyright Notice This document is copyrighted, 2011. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Embedded Controller AEC-6635 Acknowledgments All other products’ name or trademarks are properties of their respective owners. AMI is a trademark of American Megatrends Inc. CompactFlash™ is a trademark of the Compact Flash Association. Microsoft Windows is a registered trademark of Microsoft Corp. Intel®, Core™ are trademarks of Intel Corporation. PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation.
Embedded Controller AEC-6635 Packing List Before you begin operating the product, please make sure that the following materials are enclosed: 1 AEC-6635 Embedded Controller 2 Wallmount Brackets 1 Screw Package 1 RAM Thermal Pad (60mm x 25mm x 3mm) 1 DVD-ROM for manual (in PDF format) and drivers If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
Embedded Controller AEC-6635 Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a firm surface during installation.
Embedded Controller AEC-6635 d. The equipment does not work well, or you cannot get it to work according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20°C (-4°F) OR ABOVE 70°C (158°F). IT MAY DAMAGE THE EQUIPMENT. FCC This device complies with Part 15 FCC Rules.
Embedded Controller AEC-6635 ENERGY STAR This Product has been certified by ENERGY STAR® The Regulation of ENERGY STAR®: ENERGY STAR® Requirements for Computer Version 5.2. The Test Standard of ENERGY STAR®: IEC/EN 62301, ENERGY STAR® Program Requirements for Computer Version ENERGY STAR® Compliance: Power Management features (Basic) Using power-saving states The system provides the two power-saving states: Sleep and Hibernation. When Sleep is initiated, the power lights blink and the screen clears.
Embedded Controller AEC-6635 Initiating and exiting Sleep The system set the Sleep mode after 30 minutes of inactivity when running on external power. You can change to none Sleep mode if the system needs to be active at all time. The default power management settings have been selected for compliance with ENERGY STAR®, and are recommended by the ENERGY STAR® program for optimal energy savings.
Embedded Controller AEC-6635 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Boxer/ Industrial System 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 硬盘 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 外壳 中央处理器 与内存 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注： 一、此产品所标示之环保使用期限，系指在一般正常使用状况下。 二、上述
Embedded Controller AEC-6635 Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Hardware Installation 2.1 Dimension & Connectors of AEC-6635..................... 2-2 2.2 Connectors and Jumpers of the Main Board ............ 2-4 2.3 List of Jumpers ....
Embedded Controller AEC-6635 Chapter 1 General Information Chapter 1 General Information 1- 1
Embedded Controller AEC-6635 1.1 Introduction The newest Boxer series AEC-6635 has been introduced by AAEON and it utilizes Intel® Core™ i7 620M 2.66 GHz/ Core™ i5 520M 2.4 GHz processor. This condensed Embedded Controller is a fanless controller with the latest Intel® processor and chipset. The cutting-edge technology has been equipped to the AEC-6635 to satisfy the versatile demands of Factory Automation, Vehicle, and Digital Signage.
Embedded Controller AEC-6635 1.2 Features Intel® Core™ i7 620M/ Core™ i5 520M Processor Intel® QM57 Chipset Supports DVI-D x 1, VGA x 1, DIO x 1, DisplayPort x 1 Up To COM x 4 Up To USB x 6 Fanless Operation Gigabit Ethernet x 2 2.
Embedded Controller AEC-6635 1.3 Specifications Intel® Core™ i7 620M 2.66 GHz/ CPU Intel® Core™ i5 520M 2.4 GHz Intel® QM57 Chipset System Memory Display VGA 204-pin DDR3 SODIMM x 1, Max. 4 GB D-Sub 15 x 1, shared system memory up to 512 MB DVI DVI-D x 1 Others DisplayPort x 1 Storage SSD CompactFlash™ Slot x 1 Device HDD 2.5” SATA Hard Disk Drive Bay x 1 Network LAN Gigabit Ethernet, RJ-45 x 2 USB Host USB2.
Embedded Controller AEC-6635 Power Consumption Intel® Core™ i7 620M, 4.06A @ 9V System Cooling Passive Cooling Mounting Wallmount Operating Temperature -4oF ~122oF (-20oC~50oC) Storage Temperature -4oF ~158oF (-20oC~70oC) Anti-Vibration Anti-Shock 5 g rms/5~500 Hz/ random operation (CFD); 1 g rms/5~500 Hz/ random operation (HDD) 50 G peak acceleration (11 msec, duration)-CFD 20 G peak acceleration (11 msec, duration)-HDD Certification EMC CE/FCC Class A Dimension 8.35” (W) x 2.52” (H) x 9.
Embedded Controller AEC-6635 Chapter 2 Hardware Installation Chapter 2 Hardware Installation 2-1
Embedded Controller AEC-6635 2.
Embedded Controller AEC-6635 Connectors on the front panel V+ V- FG DC IN 9-30V Connectors on the rear panel Chapter 2 Hardware Installation 2 - 3
Embedded Controller AEC-6635 2.
Embedded Controller AEC-6635 Solder Side Chapter 2 Hardware Installation 2 - 5
Embedded Controller AEC-6635 2.3 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application. The table below shows the function of each of the board's jumpers: Label Function JP2 PCI-104 I/O Voltage Selection JP3-1 LCD Inverter/Backlight Voltage Selection JP3-2 LVDS LCD Voltage Selection JP4-1 Clear CMOS JP4-2 Clear ME ROM JP5 Touch Screen 4/5/8-wire Mode Selection JP6 COM2 RI/+5V/+12V Selection SW1 AT/ATX Power Mode Selection 2.
Embedded Controller AEC-6635 CN9 Touch Panel Connector CN11 RS-232 Serial Port 1 Connector CN12 Display Port Connector CN13 UIM Connector CN14 PCI-104 Connector CN16,CN37 DDR3 SODIMM Slot CN17,CN31,CN32 USB Connector CN19 PCI Express Mini Card Connector CN20 LPT Port Connector CN21 Digital I/O Connector CN23 PS2 Keyboard/Mouse Connector CN24 PCIe/104 Connector CN25 RS-232 Serial Port 4 Connector CN26 RS-232 Serial Port 3 Connector CN27 External SMBUS and PS_ON# Connector CN28
Embedded Controller AEC-6635 2.
Embedded Controller AEC-6635 2.
Embedded Controller AEC-6635 2.7 Hard Disk Drive (HDD) Installation Step 1: Get the HDD and HDD Bracket ready.
Embedded Controller AEC-6635 Step 3: Close the bottom cover of the AEC-6635 and fasten the screws Chapter 2 Hardware Installation 2 - 11
Embedded Controller AEC-6635 2.
Embedded Controller AEC-6635 Step 3: Insert the RAM at 30-degree angle to the memory slot and press Step 4: Adhere the heat spreading pad onto the RAM Chapter 2 Hardware Installation 2 - 13
Embedded Controller AEC-6635 2.9 Wallmount Kit Installation Get the brackets ready and fasten appropriate four screws on each bracket. After fastening the two brackets on the bottom lid of AEC-6635, the wallmount kit installation has been finished.
Embedded Controller AEC-6635 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
Embedded Controller 3.1 AEC-6635 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. System configuration verification These routines check the current system configuration against the values stored in the CMOS memory.
Embedded Controller 3.2 AEC-6635 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
Embedded Controller AEC-6635 Chapter 4 Driver Installation Chapter 4 Driver Installation 4-1
Embedded Controller AEC-6635 The AEC-6635 comes with a DVD-ROM that contains all drivers your need. Follow the sequence below to install the drivers: Step 1 – Install Chipset Driver Step 2 – Install VGA Driver Step 3 – Install LAN Driver Step 4 – Install ME Driver Step 5 – Install AHCI Driver Please read following instructions for detailed installations.
Embedded Controller AEC-6635 4.1 Installation Insert the AEC-6635 DVD-ROM into the DVD-ROM Drive. And install the drivers from Step 1 to Step 5 in order. Step 1 – Install Chipset Driver 1. Click on the Step1- CHIPSET folder and then double click on the infinst_autol(9.1.1.1020).exe 2. Follow the instructions that the window shows 3. The system will help you to install the driver automatically Step 2 – Install VGA Driver 1. Click on the Step2- VGA folder and select the OS your system is 2.
Embedded Controller AEC-6635 3.
Embedded Controller AEC-6635 Step 3: The setting procedures “ In BIOS Setup Menu” A: Advanced -> SATA Configuration -> SATA Configuration -> SATA Mode -> AHCI Mode Step 4: The setting procedures “In BIOS Setup Menu” B: Boot -> Boot Option #1 -> DVD-ROM Type Chapter4 Drivers Installation 4-5
Embedded Controller AEC-6635 Step 5: The setting procedures “In BIOS Setup Menu” C: Save & Exit -> Save Changes and Exit Step 6: Setup OS Chapter 4 Driver Installation 4-6
Embedded Controller AEC-6635 Step 7: Press “F6” Step 8: Choose “S” Chapter4 Drivers Installation 4-7
Embedded Controller AEC-6635 Step 9: Choose “Intel(R) 5 Series 6 Port SATA AHCI Controller” Step 10: It will show the model number you select and then press “ENTER” Chapter 4 Driver Installation 4-8
Embedded Controller AEC-6635 Step 11: Setup is loading files Chapter4 Drivers Installation 4-9
Embedded Controller AEC-6635 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
Embedded Controller AEC-6635 A.1 Programming AEC-6635 utilizes ITE 8781 chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON initial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the ITE 8781 enters the normal mode with all logical devices disabled except KBC.
Embedded Controller AEC-6635 There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode. Undesired result may occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state.
Embedded Controller AEC-6635 WatchDog Timer Configuration Registers Configure Control (Index=02h) This register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them.
Embedded Controller AEC-6635 Watch Dog Timer 1, 2, 3 Configuration Register (Index=72h, 82h, 92h Default=001s0000b) Watch Dog Timer 1,2,3 Time-Out Value (LSB) Register (Index=73h,83h,93h, Default=38h) Watch Dog Timer 1,2,3 Time-Out Value (MSB) Register (Index=74h,84h,94h Default=00h) Appendix A Programming the Watchdog Timer A-5
Embedded Controller AEC-6635 A.2 ITE8781 Watchdog Timer Initial Program .MODEL SMALL .CODE Main: CALL Enter_Configuration_mode CALL Check_Chip mov cl, 7 call Set_Logic_Device ;time setting mov cl, 10 ; 10 Sec dec al Watch_Dog_Setting: ;Timer setting mov al, cl mov cl, 73h call Superio_Set_Reg ;Clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call Superio_Set_Reg ;unit is second.
Embedded Controller AEC-6635 call Superio_Set_Reg ; game port enable mov cl, 9 call Set_Logic_Device Initial_OK: CALL Exit_Configuration_mode MOV AH,4Ch INT 21h Enter_Configuration_Mode PROC NEAR MOV SI,WORD PTR CS:[Offset Cfg_Port] MOV DX,02Eh MOV CX,04h Init_1: MOV AL,BYTE PTR CS:[SI] OUT DX,AL INC SI LOOP Init_1 RET Enter_Configuration_Mode ENDP Exit_Configuration_Mode PROC NEAR MOV AX,0202h Appendix A Programming the Watchdog Timer A-7
Embedded Controller CALL Write_Configuration_Data RET Exit_Configuration_Mode ENDP Check_Chip PROC NEAR MOV AL,20h CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MOV AL,21h CALL Read_Configuration_Data CMP AL,81h JNE Not_Initial Need_Initial: STC RET Not_Initial: CLC RET Check_Chip ENDP Read_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] Appendix A Programming the Watchdog Timer A-8 AEC-6635
Embedded Controller AEC-6635 OUT DX,AL MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Write_Configuration_Data ENDP Superio_Set_Reg proc near push ax MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret Superio_Set_Reg endp.
Embedded Controller Set_Logic_Device proc AEC-6635 near push ax push cx xchg al,cl mov cl,07h call Superio_Set_Reg pop cx pop ax ret Set_Logic_Device endp ;Select 02Eh->Index Port, 02Fh->Data Port Cfg_Port DB 087h,001h,055h,055h DW 02Eh,02Fh END Main Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 . .
