Embedded Controller AEC-6876 AEC-6876 Fanless Embedded Controller Intel® CoreTM i5-2510E/ Celeron® -B810 Processor with 2 Gigabit Ethernet 4 COM, 4 USB, 1 PCI-Express[x4] DVI, HDMI, VGA AEC-6876 Manual 2nd Ed.
Embedded Controller AEC-6876 Copyright Notice This document is copyrighted, 2014. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Embedded Controller AEC-6876 Acknowledgments Award is a trademark of Award Software International, Inc. CompactFlash is a trademark of the Compact Flash Association. Intel , Celeron and Core are trademarkes of Intel Corporation. Microsoft Windows is a registered trademark of Microsoft Corp. PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation. ™ ® ™ ® ® ® All other product names or trademarks are properties of their respective owners.
Embedded Controller AEC-6876 Packing List Before you begin operating your PC, please make sure that the following materials have been shipped: 1 AEC-6876 Embedded Controller 1 Phoenix Power Connector 4 M3 x 4mm Screws 6 6# -32 x 10mm Screws 2 Wallmount Brackets 1 DVD-ROM for manual (in PDF format) and Drivers If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
Embedded Controller AEC-6876 Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a firm surface during installation.
Embedded Controller AEC-6876 d. The equipment does not work well, or you cannot get it to work according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20°C (-4°F) OR ABOVE 70°C (158°F). IT MAY DAMAGE THE EQUIPMENT. FCC This device complies with Part 15 FCC Rules.
Embedded Controller AEC-6876 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Boxer/ Industrial System 有毒有害物质或元素 部件名称 铅 汞 (Pb) (Hg) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 硬盘 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 外壳 中央处理器 与内存 镉 六价铬 多溴联苯 多溴二苯 (Cd) (Cr(VI)) (PBB) 醚(PBDE) O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注： 一、此产品所标示之环保使用期限，系指在一般正常使用状况下。 二、上述部件
Embedded Controller AEC-6876 Contents Chapter 1 General Information 1.1 Introduction ................................................................ 1-2 1.2 Features .................................................................... 1-4 1.3 Specifications ............................................................ 1-5 Chapter 2 Hardware Installation 2.1 Dimension ................................................................. 2-2 2.2 RS-232 Box Header (COM1) ....................................
Embedded Controller AEC-6876 A.2 ITE8728 Watchdog Timer Initial Program..............A-6 Appendix B I/O Information B.1 I/O Address Map ..................................................B-2 B.2 Memory Address Map ..........................................B-4 B.3 IRQ Mapping Chart ..............................................B-5 B.4 DMA Channel Assignments .................................B-5 Appendix C RAID & AHCI Settings C.1 Setting RAID .........................................................
Embedded Controller AEC-6876 Chapter 1 General Information Chapter 1 General Information 1-1
Embedded Controller AEC-6876 1.1 Introduction Due to the growing popularity from the IPC market, the newest Boxer series AEC-6876 has been introduced by AAEON. New Innovation for Entertainment Multimedia Domain In this era of information explosion, the advertising of consumer products will not be confined to the family television, but will also spread to high-traffic public areas, like department stores, the bus, transportation station, the supermarket etc.
Embedded Controller AEC-6876 5 g rms. With the anti-vibration hard drive device option, the AEC-6876 can be used in high vibration environments. In addition, the AEC-6876 offers low power consumption system that while operating in ambient temperatures ranging from -10° to 55°C. The AEC-6876 is a standalone high performance controller designed for long-life operation and with high reliability. It can replace traditional methods and become the mainstream controller for the multimedia entertainment market.
Embedded Controller AEC-6876 1.
Embedded Controller AEC-6876 1.3 Specifications Intel® CoreTM i5-2510E 2.5 GHz/ CPU Celeron®-B810 1.6 GHz Processor Chipset Intel® QM67 System Memory DDR3 SODIMM x 2, Max.
Embedded Controller Indicator AEC-6876 Mini Card 1 Front Power LED x 1, HDD active LED x 1 Power Requirement DC-in 12V, with DC jack lockable, DC 9~30V with 3-pin terminal block System Cooling Passive cooling Mounting Wallmount Operating Temperature 14 oF ~ 122oF (-10oC ~ 50oC)—without airflow 14 oF ~ 131oF (-10oC ~ 55oC)—with airflow Storage Temperature -4oF ~ 158oF (-20oC ~ 70oC) Anti-Vibration 5 g rms/ 5~500 Hz/ operation-CFast™; 1 g rms/ 5~500 Hz/ operation-HDD Anti-Sh
Embedded Controller AEC-6876 Chapter 1 General Information 1-7
Embedded Controller AEC-6876 Chapter 2 Hardware Installation Chapter 2 Hardware Installation 2-1
Embedded Controller 2.
Embedded Controller AEC-6876 A1M/A2M Version Chapter 2 Hardware Installation 2 - 3
Embedded Controller AEC-6876 2.2 RS-232 Box Header (COM1) 4B P in 25B S ignal Pin S ignal 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 5B 2.
Embedded Controller AEC-6876 RS-485 Mode Pin Signal Pin Signal 1 D- 2 NC 3 D+ 4 NC 5 Ground 6 NC 7 NC 8 NC 9 NC 2.4 RS-232 Box Header (COM3~COM6) 4B P in 25B S ignal Pin S ignal 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 5B 2.
Embedded Controller AEC-6876 2.
Embedded Controller AEC-6876 Step 2: Unfasten the six screws on the bottom lid Step 3: Place the HDD to the HDD bracket and fasten to the bottom lid of AEC-6876 Chapter 2 Hardware Installation 2 - 7
Embedded Controller AEC-6876 Step 4: Fasten the screws on the front and rear panels, and the brackets of AEC-6876 Chapter 2 Hardware Installation 2 - 8
Embedded Controller AEC-6876 2.
Embedded Controller AEC-6876 2.
Embedded Controller AEC-6876 Step 2: Unfasten the six screws on the bottom lid Step 3: Install a hold-down bracket to fix the PCI or PCI-Express Card and make sure the PCI or PCI-Express Card installs properly Chapter 2 Hardware Installation 2 - 11
Embedded Controller AEC-6876 2.9 Wallmount Bracket Installation Fasten the brackets with the appropriate screws.
Embedded Controller AEC-6876 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
Embedded Controller 3.1 AEC-6876 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. System configuration verification These routines check the current system configuration against the values stored in the CMOS memory.
Embedded Controller 3.2 AEC-6876 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
Embedded Controller AEC-6876 Chapter 4 Driver Installation .
Embedded Controller AEC-6876 The AEC-6876 comes with an AutoRun DVD-ROM that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver DVD, the driver DVD-title will auto start and show the installation guide. If not, please follow the sequence below to install the drivers.
Embedded Controller 4.1 AEC-6876 Installation: Insert the AEC-6876 DVD-ROM into the DVD-ROM drive. And install the drivers from Step 1 to Step 8 in order. Step 1 – Install Chipset Driver 1. Click on the STEP 1-CHIPSET folder and select the OS folder your system is 2. Double click on the infinst_autol.exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 2 – Install VGA Driver 1.
Embedded Controller AEC-6876 Note 2: If the OS is Windows® XP, you have to install the driver of dotNet Framework first. Simply click on dotnetfx35.exe located in dotNet Framwork folder. Step 3 –Install LAN Driver 1. Click on the STEP3-LAN folder and select the OS folder your system is and then select the folder of Intel 82576LM or Realtek 8111E based on the LAN chipset in your system 2. Double click on the .exe file 3. Follow the instructions that the window shows 4.
Embedded Controller AEC-6876 Step 6 – Install RAID & AHCI Driver Please refer to the Appendix C RAID & AHCI Settings Step 7 – Install TPM Driver 1. Click on the STEP7-TPM folder and select the folder of OS folder your system is 2. Double click on the Setup.exe located in each OS folder 3. Follow the instructions that the window shows 4.
Embedded Controller AEC-6876 2. Change User Account Control Settings to [Never notify] 3. Reboot and Administrator login.
Embedded Controller AEC-6876 4. To run patch.bat with [Run as administrator].
Embedded Controller AEC-6876 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
Embedded Controller AEC-6876 A.1 Programming AEC-6876 utilizes ITE IT8728 chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the ITE IT8728 enters the normal mode with all logical devices disabled except KBC.
Embedded Controller AEC-6876 There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode. Undesired result may occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state.
Embedded Controller AEC-6876 WatchDog Timer Configuration Registers Configure Control (Index=02h) This register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them.
Embedded Controller AEC-6876 WatchDog Timer Control Register (Index=71h, Default=00h) WatchDog Timer Configuration Register (Index=72h, Default=00h) WatchDog Timer Time-out Value Register (Index=73h, Default=00h) Appendix A Programming the Watchdog Timer A-5
Embedded Controller AEC-6876 A.2 ITE8728 Watchdog Timer Initial Program .MODEL SMALL .CODE Main: CALL Enter_Configuration_mode CALL Check_Chip mov cl, 7 call Set_Logic_Device ;time setting mov cl, 10 ; 10 Sec dec al Watch_Dog_Setting: ;Timer setting mov al, cl mov cl, 73h call Superio_Set_Reg ;Clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call Superio_Set_Reg ;unit is second.
Embedded Controller AEC-6876 ; game port enable mov cl, 9 call Set_Logic_Device Initial_OK: CALL Exit_Configuration_mode MOV AH,4Ch INT 21h Enter_Configuration_Mode PROC NEAR MOV SI,WORD PTR CS:[Offset Cfg_Port] MOV DX,02Eh MOV CX,04h Init_1: MOV AL,BYTE PTR CS:[SI] OUT DX,AL INC SI LOOP Init_1 RET Enter_Configuration_Mode ENDP Exit_Configuration_Mode PROC NEAR MOV AX,0202h CALL Write_Configuration_Data Appendix A Programming the Watchdog Timer A-7
Embedded Controller AEC-6876 RET Exit_Configuration_Mode ENDP Check_Chip PROC NEAR MOV AL,20h CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MOV AL,21h CALL Read_Configuration_Data CMP AL,12h JNE Not_Initial Need_Initial: STC RET Not_Initial: CLC RET Check_Chip ENDP Read_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL Appendix A Programming the Watchdog Timer A-8
Embedded Controller AEC-6876 MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Write_Configuration_Data ENDP Superio_Set_Reg proc near push ax MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret Superio_Set_Reg endp.
Embedded Controller AEC-6876 push ax push cx xchg al,cl mov cl,07h call Superio_Set_Reg pop cx pop ax ret Set_Logic_Device endp ;Select 02Eh->Index Port, 02Fh->Data Port Cfg_Port DB 087h,001h,055h,055h DW 02Eh,02Fh END Main Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 . .
Embedded Controller AEC-6876 Appendix B I/O Information Appendix B I/O Information B-1
Embedded Controller B.
Embedded Controller AEC-6876 Appendix B I/O Information B-3
Embedded Controller B.
Embedded Controller AEC-6876 B.3 IRQ Mapping Chart B.
Embedded Controller AEC-6876 Appendix C RAID & AHCI Settings Appendix C RAID & AHCI Settings C-1
Embedded Controller AEC-6876 C.
Embedded Controller AEC-6876 Step 3: The setting procedures “ In BIOS Setup Menu” A: Advanced -> SATA Configuration -> SATA Mode -> RAID Mode Step 4: The setting procedures “In BIOS Setup Menu” B: Advanced -> Launch Storage OpROM -> Enabled Appendix C RAID & AHCI Settings C-3
Embedded Controller AEC-6876 Step 5: The setting procedures “In BIOS Setup Menu” C: Boot -> Boot Option #1 -> DVD-ROM Type Step 6: The setting procedures “In BIOS Setup Menu” D: Save & Exit -> Save Changes and Exit Appendix C RAID & AHCI Settings C-4
Embedded Controller AEC-6876 Step 7: Press Ctrl-I to enter MAIN MENU Step 8: Choose “1.
Embedded Controller Step 9: RAID Level -> RAID0(Stripe) Step 10: Choose “Create Volume” Appendix C RAID & AHCI Settings C-6 AEC-6876
Embedded Controller AEC-6876 Step 11: Choose “Y” Step 12: Choose “5.
Embedded Controller Step 13: Choose “Y” Step 14: Setup OS Appendix C RAID & AHCI Settings C-8 AEC-6876
Embedded Controller AEC-6876 Step 15: Press “F6” Step 16: Choose “S” Appendix C RAID & AHCI Settings C-9
Embedded Controller AEC-6876 Step 17: Choose “Intel(R) ICH8M-E/ICH9M-E/5 Series SATA RAID Controller” Step 18: It will show the model number you select and then press “ENTER” Appendix C RAID & AHCI Settings C-10
Embedded Controller AEC-6876 Step 19: Setup is starting Windows Appendix C RAID & AHCI Settings C-11
Embedded Controller AEC-6876 C.
Embedded Controller AEC-6876 Step 3: The setting procedures “ In BIOS Setup Menu” A: Advanced -> SATA Configuration -> SATA Configuration -> SATA Mode -> AHCI Mode Step 4: The setting procedures “In BIOS Setup Menu” B: Boot -> Boot Option #1 -> DVD-ROM Type Appendix C RAID & AHCI Settings C-13
Embedded Controller AEC-6876 Step 5: The setting procedures “In BIOS Setup Menu” C: Save & Exit -> Save Changes and Exit Step 6: Setup OS Appendix C RAID & AHCI Settings C-14
Embedded Controller AEC-6876 Step 7: Press “F6” Step 8: Choose “S” Appendix C RAID & AHCI Settings C-15
Embedded Controller AEC-6876 Step 9: Choose “Intel(R) 5 Series 6 Port SATA AHCI Controller” Step 10: It will show the model number you select and then press “ENTER” Appendix C RAID & AHCI Settings C-16
Embedded Controller AEC-6876 Step 11: Setup is loading files Appendix C RAID & AHCI Settings C-17
