Embedded Controller AEC-6915 Rev.B AEC-6915 Rev.B Fanless Embedded Controller Intel® CoreTM 2 Duo Processor, 4 PCI slots, 4 COMs, 4 USB, Audio, VGA, Single LAN AEC-6915 Rev.B Manual 1st Ed.
Embedded Controller AEC-6915 Rev.B Copyright Notice This document is copyrighted, 2010. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Embedded Controller AEC-6915 Rev.B Acknowledgments All other products’ name or trademarks are properties of their respective owners. • Award is a trademark of Award Software International, Inc. • CompactFlash™ is a trademark of the Compact Flash Association. • Intel®, Core™ 2 Duo are trademarks of Intel® Corporation. • Microsoft Windows is a registered trademark of Microsoft Corp. • PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation.
Embedded Controller AEC-6915 Rev.B Packing List Before you begin operating your PC, please make sure that the following materials are enclosed: 1 AEC-6915 Rev.B Embedded Controller 1 Phoenix Power Connector 2 Wallmount Brackets 1 Audio Cable 1 Screw Package 1 CD-ROM for manual (in PDF format) and drivers If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
Embedded Controller AEC-6915 Rev.B Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a firm surface during installation.
Embedded Controller AEC-6915 Rev.B d. The equipment does not work well, or you cannot get it to work according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20°C (-4°F) OR ABOVE 60°C (140°F). IT MAY DAMAGE THE EQUIPMENT. FCC This device complies with Part 15 FCC Rules.
Embedded Controller AEC-6915 Rev.
Embedded Controller AEC-6915 Rev.B Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-4 1.3 Specifications ............................................................ 1-5 Chapter 2 Hardware Installation 2.1 Jumper and Connector.............................................. 2-2 2.2 FAN Power Selection (JP1) (For special usage) ...... 2-3 2.
Embedded Controller AEC-6915 Rev.B Chapter 4 Driver Installation 4.1 Installation ................................................................. 4-3 Appendix A Programming The Watchdog Timer A.1 Programming ........................................................A-2 A.2 IT8712 Watchdog Timer Initial Program ..............A-6 Appendix B I/O Information B.1 I/O Address Map ..................................................B-2 B.2 Memory Address Map ..........................................B-3 B.
Embedded Controller AEC-6915 Rev.
Embedded Controller AEC-6915 Rev.B 1.1 Introduction The AEC-6915 Rev.B BOXER 2 Advanced Embedded Control system continues the BOXER design concept but focuses on the fast expanding Machine Automation market. The AEC-6915 Rev.B can provide four PCI slots for expansion. Therefore AEC-6915 Rev.
Embedded Controller AEC-6915 Rev.B AAEON not only enhances your competitive value but also gives you an excellent solution for the future. Strict Quality Control Process AAEON retains the perfect product design and management team. Our Quality Control through multiple level experience and test has earned a good reputation in IPC field. AAEON’s whole product series are subjected to high-level standards which make them our best guarantee and assurance to customers.
Embedded Controller AEC-6915 Rev.B 1.2 Features • All I/O on the same side (front panel) • Supports Intel® CoreTM 2 Duo Processor up to 2.
Embedded Controller AEC-6915 Rev.B 1.3 Specifications System • CPU: Intel® CoreTM 2 Duo Processor • System Memory: DDR II SDRAM SODIMM x 1, Max. 2GB • Expansion: PCI slot x 4 • VGA: DB-15 VGA connector • Keyboard/Mouse: PS/2 Keyboard & Mouse • Ethernet: 10/100/1000Base-TX RJ-45 Connector x 1 • SSD: CompactFlash™ slot x 1 (Internal) • Device Bay: Internal 2.
Embedded Controller AEC-6915 Rev.B Converter (Default) Input voltage: DC 9V/4.38A~ DC 30V/1.52A 2. AC Input -- External Power Adapter (Optional) Input voltage: 100V AC ~ 240V AC @ 50 ~ 60Hz Mechanical and Environmental • Construction: Rugged Aluminum Alloy chassis • Color: Mustard • Mounting: Wallmount • Dimension: 6.1”(W) x 8.89”(H) x 9.4”(D) (154.3mm x 225.7mm x 237.8mm) • Net Weight: • Operating Temperature: 5°F ~ 131°F (-15°C~55°C) 14.3 lb (6.5 kg) (Pentium M 2.
Embedded Controller AEC-6915 Rev.B operation (CFD); 3g rms / 5~500Hz / random operation (Internal HDD active Module) • Shock: 50g peak acceleration (11msec. duration)(CFD) 20g peak acceleration (11 msec.
Embedded Controller AEC-6915 Rev.
Embedded Controller AEC-6915 Rev.
Embedded Controller AEC-6915 Rev.
Embedded Controller AEC-6915 Rev.B 2.
Embedded Controller AEC-6915 Rev.B 2.2 FAN Power Selection (JP1) (For special usage) JP1 Function 1-2 +12V 2-3 +5V JP1 1 +12V 1 1 1 +5V JP1 1 1 2.
Embedded Controller AEC-6915 Rev.B 2.
Embedded Controller AEC-6915 Rev.B 2.5 RTC Battery Selection (JP6) JP6 Function 1-2 Normal (Default) 2-3 Clear CMOS JP6 1 JP6 1 Normal (Default) 1 Clear CMOS 1 1 2.6 LVDS Power Selection (JP7) (Optional) JP7 Function 1-2 +5V 2-3 +3.3V (Default) 1 JP7 JP7 1 +5V 1 1 1 1 +3.
Embedded Controller AEC-6915 Rev.B 2.7 CF Slot Master/Slave Selection (JP8) JP8 Function 1-2 Slave 2-3 Master (Default) JP8 1 Slave 1 Master (Default) 1 1 JP8 1 2.
Embedded Controller AEC-6915 Rev.
Embedded Controller AEC-6915 Rev.B 2.9 COM2 RS-232/422/485 Selection COM2 RS-232/422/485 selection for AAEON BOXER S series is set in BIOS setting as following: Entering BIOS Setting Menu: Choose "Integrated PeripheralsÆ Super IO device Æ COM2 select". (Default setting is at "RS-232") 2.10 COM2 RS-232/422/485 Serial Port Connector Different devices implement the RS-232/422/485 standard in different ways. If you have problems with a serial device, check the pin assignments below for the connector.
Embedded Controller AEC-6915 Rev.B 2.11 Hard Disk Drive Installation For Hard Disk Drive (HDD) installation, you have to disassemble the bottom lid of AEC-6915 Rev.B and some components and covers in the AEC-6915 Rev.B and then install the HDD. Step 1: Unfasten the four screws on the side panel. Step 2: Unfasten the four screws on the HDD cover.
Embedded Controller AEC-6915 Rev.B Step 3: Get the HDD module and HDD cover ready. Use the four screws to fasten the HDD cover and HDD module.
Embedded Controller AEC-6915 Rev.B Step 5: Connect the HDD cable (for SATA HDD) HDD DISK SATA Power W/LOCK I/O Board Side Step 6: Fasten the four screws on the side panel of the AEC-6915 Rev.
Embedded Controller AEC-6915 Rev.B 2.12 PCI Card Installation Step 1: Unfasten the four screw on the side panel. Step 2: Remove the screw with your finger and get the PCI card ready to install. You should keep the shield and screw for use later.
Embedded Controller AEC-6915 Rev.B Step 3: Insert the PCI card into the PCI slot and reattach the screw. Step 4: Unfasten the screws and push the tenon to lock the PCI card in position.
Embedded Controller AEC-6915 Rev.B Step 5: Close the side lid of the AEC-6915 Rev.B and fasten four screws on side lid.
Embedded Controller AEC-6915 Rev.B 2.13 Wallmount kit Installation Step 1: Get the brackets ready and fasten appropriate two screws on each bracket. After fastening the two brackets on the rear panel of AEC-6915 Rev.
Embedded Controller AEC-6915 Rev.
Embedded Controller AEC-6915 Rev.
Embedded Controller AEC-6915 Rev.B 3.1 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
Embedded Controller AEC-6915 Rev.B 3.2 Award BIOS Setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press immediately. This will allow you to enter Setup. Standard CMOS Features Use this menu for basic system configuration. (Date, time, IDE, etc.
Embedded Controller AEC-6915 Rev.B Frequency/Voltage Control Use this menu to specify your settings for auto detect DIMM/PCI clock and spread spectrum. Load Fail-Safe Defaults Use this menu to load the BIOS default values for the minimal/stable performance for your system to operate. Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performance system operations.
Embedded Controller AEC-6915 Rev.
Embedded Controller AEC-6915 Rev.B The AEC-6915 Rev.B comes with a CD-ROM that contains all drivers and utilities that meet your needs. Follow the sequence below to install the drivers: Step 1 – Install Chip Driver Step 2 – Install VGA Driver Step 3 – Install LAN Driver Step 4 – Install Audio Driver USB 2.0 Drivers are available for download using Windows Update for both Windows XP and Windows 2000. For additional information regarding USB 2.0 support in Windows XP and Windows 2000, please visit www.
Embedded Controller AEC-6915 Rev.B 4.1 Installation Insert the AEC-6915 Rev.B CD-ROM into the CD-ROM Drive. The Autorun program will run automatically. You also can choose the drivers to install from step 1 to step 4 in order as following instructions. Step 1 – Install Chipset Driver 1. Click on the Step 1-chip folder and then double click on the infinst_autol.exe 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 2 – Install VGA Driver 1.
Embedded Controller AEC-6915 Rev.B 3. The system will help you install the driver automatically Note: Under the Window OS environment, if the CRT connector is connected to display monitor by the data switch device, the user need to set the color and resolution from Intel Graphic utility (VGA driver) instead of setting from the control panel in case of the wrong display appearance.
Embedded Controller AEC-6915 Rev.
Embedded Controller AEC-6915 Rev.B A.1 Programming AEC-6915 Rev.B utilizes ITE 8712 chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the ITE 8712 enters the normal mode with all logical devices disabled except KBC.
Embedded Controller AEC-6915 Rev.B There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode. Undesired result may occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state.
Embedded Controller AEC-6915 Rev.B WatchDog Timer Configuration Registers Configure Control (Index=02h) This register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them.
Embedded Controller AEC-6915 Rev.
Embedded Controller AEC-6915 Rev.B A.2 IT8712 Watchdog Timer Initial Program .MODEL SMALL .CODE Main: CALL Enter_Configuration_mode CALL Check_Chip mov cl, 7 call Set_Logic_Device ;time setting mov cl, 10 ; 10 Sec dec al Watch_Dog_Setting: ;Timer setting mov al, cl mov cl, 73h call Superio_Set_Reg ;Clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call Superio_Set_Reg ;unit is second.
Embedded Controller AEC-6915 Rev.
Embedded Controller AEC-6915 Rev.
Embedded Controller AEC-6915 Rev.B MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Write_Configuration_Data ENDP Superio_Set_Reg proc near push ax MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret Superio_Set_Reg endp.
Embedded Controller AEC-6915 Rev.B push ax push cx xchg al,cl mov cl,07h call Superio_Set_Reg pop cx pop ax ret Set_Logic_Device endp ;Select 02Eh->Index Port, 02Fh->Data Port Cfg_Port DB 087h,001h,055h,055h DW 02Eh,02Fh END Main Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 . .
Embedded Controller AEC-6915 Rev.
Embedded Controller B.1 I/O Address Map Appendix B I/O Information B-2 AEC-6915 Rev.
Embedded Controller AEC-6915 Rev.B B.
Embedded Controller B.3 IRQ Mapping Chart B.4 DMA Channel Assignments Appendix B I/O Information B-4 AEC-6915 Rev.
