Embedded Controller AEC-6930 AEC-6930 Fanless Embedded Controller Intel® CoreTM 2 Duo Processor With 2 PCI slots, 2 PCMCIA, 4 COMs, Audio, CompactFlash™ 4 Gigabit Ethernet AEC-6930 Manual 2nd Ed.
Embedded Controller AEC-6930 Copyright Notice This document is copyrighted, 2009. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Embedded Controller AEC-6930 Acknowledgments All other products’ name or trademarks are properties of their respective owners. • Award is a trademark of Award Software International, Inc. • CompactFlash™ is a trademark of the Compact Flash Association. • Intel®, and Core ™ 2 Duo are trademarks of Intel® Corporation. • Microsoft Windows is a registered trademark of Microsoft Corp. • PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation.
Embedded Controller AEC-6930 Packing List Before you begin operating your PC, please make sure that the following materials are enclosed: 1 AEC-6930 Embedded Controller 1 Phoenix Power Connector 2 Wallmount Brackets 1 Audio Cable 1 Screw Package 1 PS/2 Expansion Cable for Keyboard and Mouse 1 IDE 44-pin Flat Cable 1 SATA Cable 1 SATA Power Cable 1 DVI-I to CRT & DVI-D Y Cable 1 Mounting Bracket 1 CD-ROM for Manual (in PDF format) and Drivers If any of these items should be missing
Embedded Controller AEC-6930 Application Note 1. MXM Card Installation Notice: MXM slot (for MXM video card expansion, the DVI output adapter was installed already. If you want to install other MXM video cards, the DVI output adapter has to be removed first.
Embedded Controller AEC-6930 Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a firm surface during installation.
Embedded Controller AEC-6930 d. The equipment does not work well, or you cannot get it to work according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20°C (-4°F) OR ABOVE 60°C (140°F). IT MAY DAMAGE THE EQUIPMENT. FCC This device complies with Part 15 FCC Rules.
Embedded Controller AEC-6930 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Boxer/ Industrial System 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 硬盘 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 外壳 中央处理器 与内存 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注： 一、此产品所标示之环保使用期限，系指在一般正常使用状况下。 二、上述
Embedded Controller AEC-6930 Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-4 1.3 Specifications ............................................................ 1-5 Chapter 2 Hardware Installation 2.1 Jumpers and Connectors .......................................... 2-2 2.2 Dimension .................................................................
Embedded Controller Appendix A AEC-6930 Programming The Watchdog Timer A.1 General Information .............................................A-2 A.2 Access Interface ....................................................A-2 A.3 Registers Description.............................................A-3 A.4 F75111 Watchdog Timer Initial Program ...............A-5 Appendix B I/O Information B.1 I/O Address Map ..................................................B-2 B.2 Memory Address Map .........................
Embedded Controller AEC-6930 Chapter 1 General Information Chapter 1 General Information 1- 1
Embedded Controller AEC-6930 1.1 Introduction The AEC-6930 BOXER 2 Advanced Embedded Control system continues the BOXER design concept but focuses on the fast expanding Machine Automation market. The AEC-6930 can provide two PCI slot for expansion.
Embedded Controller AEC-6930 not only enhances your competitive value but also gives you an excellent solution for the future. Strict Quality Control Process AAEON retains the perfect product design and management team. Our Quality Control through multiple level experience and test has earned a good reputation in IPC field. AAEON’s whole product series are subjected to high-level standards which make them our best guarantee and assurance to customers.
Embedded Controller AEC-6930 1.2 Features • Fanless Design with Intel® CoreTM 2 Duo 1.60 GHz (L7500) Processors • Supports 2 PCI Slots for Expansion • 2 PCMCIA • 4 COM / 4 USB 2.
Embedded Controller AEC-6930 1.3 Specifications System • CPU: Intel® CoreTM 2 Duo 1.60 GHz(L7500) Processor • System Memory: DDR II SDRAM SODIMM x 2, Max. 2GB x 2 • Expansion: PCI slot x 2; PCMCIA x 2 • Video Interface: DVI-I; The VGA output can apply to the Y cable. • Keyboard/Mouse: PS/2 Keyboard & Mouse • Ethernet: 10/100/1000Base-TX RJ-45 Connector x 4 • SSD: CompactFlash™ slot x 1 • Device Bay: Internal 2.
Embedded Controller AEC-6930 Input voltage: DC 9V/4.3A~ DC 30V/1.29A 2. AC Input -- External Power Adapter (Optional) Input voltage: 100V AC ~ 240V AC @ 50 ~ 60Hz • System Control: Power on / off switch x 1; Reset button x 1 • Indicators: Power LED x 1; HDD active LED x 1 Mechanical and Environmental • Construction: Rugged Aluminum Alloy chassis • Color: Mustard • Mounting: Wallmount • Dimension: 8.4”(W) x 3.7”(H) x 9.4”(D) (214mm x 94.8mm x 237.
Embedded Controller • Storage Humidity: AEC-6930 5~90%@40°C, non-condensing • Vibration: 5g rms / 5~500Hz / random operation (CFD); 0.5g rms / 5~500Hz / random operation (Internal HDD bracket) • Shock: 50g peak acceleration (11msec. duration)(CFD) 20g peak acceleration (11 msec.
Embedded Controller Front Side Audio Rear Side Chapter 1 General Information 1- 8 AEC-6930
Embedded Controller AEC-6930 Chapter 2 Hardware Installation Chapter 2 Hardware Installation 2-1
Embedded Controller 2.
Embedded Controller AEC-6930 JV1/ JV2/ JV3/ JV4 JV9 Chapter 2 Hardware Installation 2 - 3
Embedded Controller JBAT1 Chapter 2 Hardware Installation 2 - 4 AEC-6930
Embedded Controller AEC-6930 2.
Embedded Controller Audio Chapter 2 Hardware Installation 2 - 6 AEC-6930
Embedded Controller AEC-6930 2.3 COM1, COM2 Pin 9 Selection (JV1, JV2) JV1/JV2 Function 1-2 +12V 3-4 +5V 5-6 RI (Default) Note: COM1 and COM2 have RS-232/422/485 function. 2.4 COM3, COM4 Pin 9 Selection (JV3, JV4) JV3/JV4 Function 1-2 +12V 3-4 +5V 5-6 RI (Default) 2.5 FAN Port Voltage Selection (JV9) JV9 Function 1-2 +5V (Default) 2-3 +12V 2.6 Clear CMOS Selection (JBAT1) JBAT1 Function 1-2 Normal (Default) 2-3 Clear CMOS 2.
Embedded Controller AEC-6930 Pin Signal Pin Signal 1 DCD1 2 RXD1 3 TXD1 4 DTR1 5 GND 6 DSR1 7 RTS1 8 CTS1 9 RI1 COM2/ RS-422 Mode Pin Signal Pin Signal 1 TXD- 2 RXD+ 3 TXD+ 4 RXD- 5 Ground 6 N/C 7 N/C 8 N/C 9 N/C 10 N/C Pin Signal COM2/ RS-485 Mode Pin Signal 1 TXD- 2 N/C 3 TXD+ 4 N/C 5 Ground 6 N/C 7 N/C 8 N/C 9 N/C 10 N/C Chapter 2 Hardware Installation 2 - 8
Embedded Controller AEC-6930 2.8 Hard Disk Drive Installation Disassemble the AEC-6930 For Hard Disk Drive (HDD) installation, you have to disassemble the bottom lid of AEC-6930 and some components and covers in the AEC-6930. Step 1: Unfasten the screw on the rear panel. Step 2: Unfasten the screw in blue circle on the front panel.
Embedded Controller AEC-6930 Step 3: Unfasten the six screws on the bottom lid.
Embedded Controller AEC-6930 Assemble the HDD Module After disassembling the AEC-6930, you have to get the HDD module ready for the proceeding installation.
Embedded Controller Step 2: Assembly the HDD chassis Step 3: Assembly the damper bracket Chapter 2 Hardware Installation 2 - 12 AEC-6930
Embedded Controller AEC-6930 Step 4: Connect the HDD cable (for IDE Type HDD) Note: Because the default setting of IDE Drive is Slave (The master was apply to CFD), when users install the IDE HDD driver in the system, the HDD will apply to drive Slave.
Embedded Controller AEC-6930 Step 5: Fasten the six screws on the back of the AEC-6930 Step 6: Fasten the screw of front panel Audio Chapter 2 Hardware Installation 2 - 14
Embedded Controller AEC-6930 Step 7: Fasten the screw of rear panel Chapter 2 Hardware Installation 2 - 15
Embedded Controller 2.9 PCI Card Installation Step 1: Unfasten the screw on the rear panel. Step 2: Unfasten the screw on the front panel.
Embedded Controller AEC-6930 Step 3: Unfasten the six screws on the bottom lid. Step 4: Remove the screw with your finger and get the PCI card ready to install. You should keep the shield and screw for use later.
Embedded Controller AEC-6930 Step 5: Insert the PCI card into the PCI slot and reattach the screw. Step 6: Unfasten the screws and push the tenon to lock the PCI card in position.
Embedded Controller AEC-6930 Step 7: Close the bottom lid of the AEC-6930 and fasten six screws on bottom lid.
Embedded Controller AEC-6930 2.10 Wallmount kit Installation Step 1: Get the brackets ready and fasten appropriate three screws on each bracket.
Embedded Controller AEC-6930 Chapter 2 Hardware Installation 2 - 21
Embedded Controller AEC-6930 Chapter 3 Award BIOS Setup Chapter 3 Award BIOS Setup 3-1
Embedded Controller AEC-6930 3.1 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
Embedded Controller AEC-6930 3.2 Award BIOS Setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press immediately. This will allow you to enter Setup. Standard CMOS Features Use this menu for basic system configuration. (Date, time, IDE, etc.
Embedded Controller AEC-6930 PC Health Status This menu allows you to set the shutdown temperature for your system. Frequency/Voltage Control Use this menu to specify your settings for auto detect DIMM/PCI clock and spread spectrum. Load Fail-Safe Defaults Use this menu to load the BIOS default values for the minimal/stable performance for your system to operate. Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performance system operations.
Embedded Controller AEC-6930 Chapter 4 Driver Installation Chapter 4 Driver Installation 4 - 1
Embedded Controller AEC-6930 The AEC-6930 comes with a CD-ROM that contains all drivers and utilities that meet your needs. Follow the sequence below to install the drivers: Step 1 – Install Chip Driver Step 2 – Install VGA Driver Step 3 – Install LAN Driver Step 4 – Install Audio Driver USB 2.0 Drivers are available for download using Windows Update for both Windows XP and Windows 2000. For additional information regarding USB 2.0 support in Windows XP and Windows 2000, please visit www.microsoft.
Embedded Controller AEC-6930 4.1 Installation Insert the AEC-6930 CD-ROM into the CD-ROM Drive. The Autorun program will run automatically. You also can choose the drivers to install from step 1 to step 4 in order as following instructions. Step 1 – Install INF Driver 1. Click on the Step 1-chip folder and then double click on the infinst_autol.exe 2. Follow the instructions that the window will show you 3. The system will help you install the driver automatically Step 2 – Install VGA Driver 1.
Embedded Controller AEC-6930 output through Hot-Key function by Intel suggestion as follows: You need to press key simultaneously to recover VGA output again. This hot-key function is only in the Windows driver version 6.14.10.4497 or later. Step 3 – Install LAN Driver 1. Click on the Step 3-LAN driver folder and select the OS your system is 2. Double click on the .exe file located in each OS folder 3. Follow the instructions that the window shows you 4.
Embedded Controller AEC-6930 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
Embedded Controller AEC-6930 A.1 General Information The AEC-6930 utilizes Fintek F75111 chipset as its watchdog timer Controller. The other Watchdog timer is set to second or minute and the range is 0 to 256 seconds or minutes. When the timeout has occurred, that will generate a status bit to indicate it and write one will be clear. A.2 Access Interface The F75111 provides one serial access interface, I2C Bus, to read/write internal registers.
Embedded Controller AEC-6930 A.3 Registers Description Configuration and Control Register – Index 01h Power-on default [7:0] =0000_1000b Bit Name Description 7 INIT Software reset for all registers including Test Mode registers. Users use only. 6 Reserved 5 EN_WDT10 4 Reserved 3 Reserved 2 Reserved 1 SMART_POWR _MANAGEMENT 0 SOFT_POWR_ DOWN Enable Reset Out. If set to 1, enable WDTOUT10# output. Default is disable.
Embedded Controller 1 WDTOUT10_OINV 0 STS_WDTOUT10 AEC-6930 WDTOUT10# output level inverting. When write 1, the output pin will be inverted. Default is low active when time is out Indicate WDTOUT10 is occurred. Write 1 to clear this bit. Writing 0 is invalid. WDTOUT Control Register – Index 35h Power-on default [7:0] =0000_0000b Bit Name Description 7 WDT10_ENABLE 6-0 WD1_PTIME Enable WDTOUT10 Output Timer. If set to 1, the WDTOUT10 timer will be started.
Embedded Controller AEC-6930 A.4 F75111 Watchdog Timer Initial Program . .MODEL SMALL .
Embedded Controller AEC-6930 push ax push cx mov dx,SMBus_Port +04h mov al,ch out dx,al call Delay5ms call Delay5ms pop ax mov dl,03h out dx,al call Delay5ms call Delay5ms pop ax mov dl,05 out dx,al call Delay5ms call Delay5ms mov dl,02h mov al,48h out dx,al call Delay5ms ;SMBus_Port(500h) ;ID cmd(Write) ;Index ;Data0 ;write data Appendix A Programming the Watchdog Timer A-6
Embedded Controller call Delay5ms mov cx, 100h AEC-6930 @@: newiodelay loop short @B ret Ct_I2CWriteByte Endp CALL Check_Chip Appendix A Programming the Watchdog Timer A-7
Embedded Controller AEC-6930 Appendix B I/O Information Appendix B I/O Information B-1
Embedded Controller B.
Embedded Controller AEC-6930 B.
Embedded Controller B.3 IRQ Mapping Chart B.
