Embedded Controller AEC-6967 AEC-6967 Fanless Embedded Controller ® Intel 2nd Generation CoreTM i/ Celeron® Processor (FCBGA1023) with 2 Gigabit Ethernet COM x 6, USB x 6, CFast, Mini Card x 2 SATA 6.0Gb/s x 2, SATA 3.0Gb/s x 2 PCI x 2 or PCI x 1 + PCI-E[x4] x 1 or PCI-E[x4] x 2 VGA x 1, HDMI x 1, DVI-D x 1 Dual-Channel 24-bit LVDS AEC-6967 Manual 1st Ed.
Embedded Controller AEC-6967 Copyright Notice This document is copyrighted, 2012. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Embedded Controller AEC-6967 Acknowledgments Award is a trademark of Award Software International, Inc. CFast™ is a trademark of the Compact Flash Association. Intel®, Celeron® and Core™ are trademarkes of Intel® Corporation. Microsoft Windows is a registered trademark of Microsoft Corp. PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation. ® All other product names or trademarks are properties of their respective owners.
Embedded Controller AEC-6967 Packing List Before you begin operating your PC, please make sure that the following materials have been shipped: 1 AEC-6967 Embedded Controller 1 Phoenix Power Connector 4 M3 x 4mm Screws 6 6# -32 x 10mm Screws 2 Wallmount Brackets 1 DVD-ROM for manual (in PDF format) and Drivers If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
Embedded Controller AEC-6967 Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a firm surface during installation.
Embedded Controller AEC-6967 d. The equipment does not work well, or you cannot get it to work according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20°C (-4°F) OR ABOVE 70°C (158°F). IT MAY DAMAGE THE EQUIPMENT. FCC This device complies with Part 15 FCC Rules.
Embedded Controller AEC-6967 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Boxer/ Industrial System 有毒有害物质或元素 部件名称 铅 汞 (Pb) (Hg) 印刷电路板 镉 六价铬 多溴联苯 多溴二苯 (Cd) (Cr(VI)) (PBB) 醚(PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 硬盘 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 及其电子组件 外部信号 连接器及线材 外壳 中央处理器 与内存 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注： 一、此产品所标示之环保使用期限，系指在一般正常使用状况下。 二、上述部件物
Embedded Controller AEC-6967 Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Hardware Installation 2.1 Dimension ................................................................. 2-2 2.2 Location of Jumpers and Connectors ....................... 2-3 2.
Embedded Controller AEC-6967 2.17 LVDS Connector (CN17)......................................... 2-12 2.18 LVDS Inverter/ Backlight Connector (CN18)........... 2-12 2.19 RS-232/422/485 Pin DEFINE (COM2).................... 2-13 2.20 RS-232 Box Header (COM3) .................................. 2-13 2.21 RS-232 Box Header (COM4) .................................. 2-13 2.22 USB Box Header (USB3~USB4) ............................ 2-13 2.23 HDD Installation ......................................................
Embedded Controller AEC-6967 Appendix C RAID & AHCI Settings C.1 Setting RAID ......................................................... C-2 C.2 Setting AHCI ....................................................... C-12 Appendix D Electrical Specifications for I/O Ports D.1 DIO Programming................................................. D-2 D.2 Digital I/O Register................................................ D-3 D.3 Digital I/O Sample Program..................................
Embedded Controller AEC-6967 Chapter 1 General Information Chapter 1 General Information 1-1
Embedded Controller AEC-6967 1.1 Introduction Due to the growing popularity from the IPC market, the newest Boxer series AEC-6967 has been introduced by AAEON. Being a control center, the AEC-6967 is suitable for Machine Control, Data Processing, Fleet Management, Data Management. AEC-6976 equips a high efficiency heat conduction mechanism. The AEC-6967 is compact in size but has attractive and flexible extension capabilities such as 6 USB2.0 ports, VGA, Audio, 6 COM ports, PCI and PCI-E[x4].
Embedded Controller AEC-6967 1.2 Features Fanless Design Intel® 2nd Generation Core™ i/ Celeron® Processor (FCBGA1023) Intel® QM67 Chipset Gigabit Ethernet, RJ-45 x 2 Intel® Integrated Graphics Engine Supports Dual View by VGA, DVI-D, HDMI SATA 6.0 Gb/s x 2, SATA 3.0 Gb/s x 2, Support RAID 0, 1, 5, 10 USB2.0 x 6, COM x 6 (2.5KV Isolation x 2), 2.
Embedded Controller AEC-6967 1.3 Specifications Intel® 2nd Generation Core™ i/ CPU Celeron® Processor (FCBGA1023) Chipset Intel® QM67 System Memory DDR3 SODIMM x 2, Max. 16 GB, support DDR3 1066/ 1333 Display VGA Interface DB-15 x 1, shared system memory up to 512MB/DVMT 5.0 DVI DVI-D x 1 (optional 2nd DVI, support 1920x1200 @ 60 Hz HDMI HDMI x 1, support 1920x1200 @ 60 Hz Others Dual-channel 24-bit LVDS (optional extension kit) Storage Device SSD CFast™ slot HDD SATA 6.
Embedded Controller AEC-6967 Isolation protection Rear I/O Expansion Indicator KB/MS PS/2 x 1 Others Power button x 1, Reset button x 1 USB Host USB2.0 x 4 LAN RJ-45 x 2 Serial Port RS-232 x 2 Audio Mic-in, Line-in, Line-out Others Power input x 1 PCIe[x1] 2 (optional) PCI 2 (optional, limited 2.
Embedded Controller AEC-6967 -4oF ~ 140oF (-20oC ~ 60oC) (35W TDP CPU) -4oF ~ 167oF (-20oC ~ 65oC) (17W TDP CPU, not include riser card Storage Temperature -4oF ~ 158oF (-20oC ~ 70oC) Anti-Vibration 3 g rms/ 5~500 Hz/ operation-CFast™; 1 g rms/ 5~500 Hz/ operation-HDD Anti-Shock 50 G peak acceleration (11 msec. duration) –CFast™ Certification EMC Dimension (W x H x D) CE/FCC Class A 8.19” x 4.9” x 9.37” (208mm x 124.
Embedded Controller AEC-6967 Chapter 1 General Information 1-7
Embedded Controller AEC-6967 Chapter 2 Hardware Installation Chapter 2 Hardware Installation 2-1
Embedded Controller 2.
Embedded Controller AEC-6967 2.
Embedded Controller JP1, JP2, JP3, JP4, JP5 Chapter 2 Hardware Installation 2 - 4 AEC-6967
Embedded Controller AEC-6967 JP8 Default Chapter 2 Hardware Installation 2 - 5
Embedded Controller JP9, JP11, J4 Chapter 2 Hardware Installation 2 - 6 AEC-6967
Embedded Controller AEC-6967 2.3 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
Embedded Controller AEC-6967 CN11 COM4 RS-232 Box Header CN13 COM5 / COM6 Connector CN15 VGA / HDMI Connector CN16 DVI-I Connector CN17 LVDS Connector CN18 LVDS Inverter / Backlight Connector CN21 Mini Card Connector With SIM CN24 Mini Card Connector CN26/CN33 PCIE*4 Connector CN27 USB X2 / PS2 Connector CN29 Digital I/O CN30 ISOLATION COM1 / COM2 Connector CN31 DC IN PWR1 ~ PWR2 SATA POWER SATA1~SATA2 SATA 3.
Embedded Controller AEC-6967 2.5 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
Embedded Controller AEC-6967 2.6 Clear CMOS (JP1) JP1 Function 1-2 Normal (Default) 2-3 Clear CMOS 2.7 Clear ME (JP2) JP2 Function 1-2 Normal (Default) 2-3 Clear ME 2.8 Inverter Power Selection (JP3) JP3 Function 1-2 +12V (Default) 2-3 +5V 2.9 LVDS Port Backlight Lightness Control Mode Selection (JP4) JP4 Function 1-2 PWM MODE 2-3 VR MODE (Default) 2.10 LCD Voltage Selection (JP5) JP5 Function 1-2 +5V 2-3 +3.3V (Default) 2.
Embedded Controller RS485 AEC-6967 5-6 close , 1-2 3-4 open 2.12 COM6 +12V/+5V/Ring Selection (JP9) JP9 Function 1-2 +12V 3-4 +5V 5-6 Ring (Default) 2.13 COM5 +12V/+5V/Ring Selection (JP11) JP6 Function 1-2 +12V 3-4 +5V 5-6 Ring (Default) 2.14 Auto Power Button (J6) J6 Function OPEN ATX (Default) 1-2 AT 2.15 SATA Power (PWR1~PWR2) Pin Signal 1 +12V 2 GND 3 GND 4 +5V 2.
Embedded Controller AEC-6967 5 SPEAKER(-) 6 SPEAKER(+) 7 Power LED (-) 8 Power LED (+) 9 Reset Switch (-) 10 Reset Switch (+) 2.
Embedded Controller AEC-6967 2.19 RS-232/422/485 Pin DEFINE (COM2) Pin Signal Pin Signal 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 2.20 RS-232 Box Header (COM3) Pin Signal Pin Signal 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 2.21 RS-232 Box Header (COM4) Pin Signal Pin Signal 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 2.
Embedded Controller AEC-6967 7 GND 8 USBD- 9 GND 10 +5V Chapter 2 Hardware Installation 2 - 14
Embedded Controller AEC-6967 2.
Embedded Controller AEC-6967 Step 3: Fasten the screws on the front and rear panels, and the brackets of AEC-6967 Chapter 2 Hardware Installation 2 - 16
Embedded Controller AEC-6967 2.
Embedded Controller AEC-6967 Step 3: Fasten the screws on the front and rear panels, and the brackets of AEC-6967 Chapter 2 Hardware Installation 2 - 18
Embedded Controller AEC-6967 2.
Embedded Controller AEC-6967 Step 3: Install a hold-down bracket to fix the PCI Card and make sure the PCI Card installs properly.
Embedded Controller AEC-6967 2.26 Wallmount Bracket Installation Fasten the brackets with the appropriate screws.
Embedded Controller AEC-6967 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
Embedded Controller 3.1 AEC-6967 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. System configuration verification These routines check the current system configuration stored in the CMOS memory and BIOS NVRAM.
Embedded Controller 3.2 AEC-6967 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM and BIOS NVRAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup.
Embedded Controller Setup Menu Setup submenu: Main Chapter 3 AMI BIOS Setup 3-4 AEC-6967
Embedded Controller AEC-6967 Setup submenu: Advanced Chapter 3 AMI BIOS Setup 3-5
Embedded Controller AEC-6967 ACPI Settings Options Summary : ACPI Sleep State Suspend Disabled S1 (CPU Stop Clock) S3 (Suspend to RAM) Default Select the Highest ACPI sleep state the system will enter when the SUSPEND button is pressed.
Embedded Controller AEC-6967 Trusted Computing Option Summary : TPM Disable Default SUPPORT Enable Enables or Disables TPM support. O.S. will not show TPM. Reset of platform is required.
Embedded Controller AEC-6967 CPU Configuration Options Summary : Intel Disabled Virtualization Enabled Default Technology When enabled, a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology Chapter 3 AMI BIOS Setup 3-8
Embedded Controller AEC-6967 Digital IO Options Summary : DIO_P#1 Input Default DIO_P#2 Input Default DIO_P#3 Input Default DIO_P#4 Input Default DIO_P#5 Output Default DIO_P#5 Direction Low Hi DIO_P#6 Output Default DIO_P#6 Direction Low Default Default Chapter 3 AMI BIOS Setup 3-9
Embedded Controller DIO_P#7 Hi Output AEC-6967 Default DIO_P#7 Direction Low Hi DIO_P#8 Output Default DIO_P#8 Direction Low Hi Set GPIO Output as Hi or Low Default Chapter 3 AMI BIOS Setup 3-10 Default
Embedded Controller AEC-6967 SATA Configuration (IDE) Options Summary : SATA Enabled Default Controller(s) Disabled Enable or disable SATA Device. SATA Mode IDE Default Selection AHCI RAID Determines how SATA controller(s) operate.
Embedded Controller AEC-6967 IDE Configuration (AHCI) Options Summary : SATA Controller(s) Disabled Enabled Default Enable or Disable SATA Port. SATA Mode IDE AHCI Selected RAID Determines how SATA controller(s) operate. SATA Port 0 Hot Plug Disable Default Enabled Designates this port as Hot Pluggable. SATA Port 1 Hot Plug Disable Default Enabled Designates this port as Hot Pluggable.
Embedded Controller AEC-6967 Designates this port as Hot Pluggable. SATA Port 3 Hot Plug Disable Default Enabled Designates this port as Hot Pluggable. SATA Port 4 Hot Plug Disable Default Enabled Designates this port as Hot Pluggable.
Embedded Controller AEC-6967 IDE Configuration (RAID) Options Summary : SATA Controller(s) Disabled Enabled Default Enable or Disable SATA Port. SATA Mode IDE AHCI Selected RAID Determines how SATA controller(s) operate. SATA Port 0 Hot Plug Disable Default Enabled Designates this port as Hot Pluggable. SATA Port 1 Hot Plug Disable Default Enabled Designates this port as Hot Pluggable.
Embedded Controller AEC-6967 Designates this port as Hot Pluggable. SATA Port 3 Hot Plug Disable Default Enabled Designates this port as Hot Pluggable. SATA Port 4 Hot Plug Disable Default Enabled Designates this port as Hot Pluggable.
Embedded Controller Intel TXT(LT) Configuration Chapter 3 AMI BIOS Setup 3-16 AEC-6967
Embedded Controller AEC-6967 PCH-FW Configuration Options Summary : Firmware Update Configuration Configure Management Engine Technology Parameters.
Embedded Controller AEC-6967 Firmware Update Configuration Options Summary : Me FW Image Disabled Default Re-Flash Enabled Enable/Disable Me FW Image Re-Flash function.
Embedded Controller AEC-6967 AMT Configuration Options Summary : Intel AMT Disabled Enabled Default Enable/Disable Intel (R) Active Management Technology BIOS Extension. Note: iAMT H/W is always enabled. This option just controls the BIOS extension execution. If enabled, this requires additional firmware in the SPI device Un-Configure Disabled Default ME Enabled OEMFlag Bit 15: Un-Configure ME without password.
Embedded Controller AEC-6967 USB Configuration Options Summary : Legacy USB Support Enabled Default Disabled Auto Enable Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.
Embedded Controller AEC-6967 Super IO Configuration Options Summary : Power Saving Disabled Default Function Enabled Enable to reduce power consumption is system off state. When Enabled, only power button can power-up system.
Embedded Controller AEC-6967 Serial Port 1 Configuration Options Summary : Serial Port Disabled Enabled Default Enable or Disable serial Port (COM) Change Settings Auto Default (Serial Port 1) IO=3F8h; IRQ=4; IO=3F8h; IRQ=3,4; IO=2F8h; IRQ=3,4’ IO=3E8h; IRQ=3,4; IO=2E8h; IRQ=3,4; Select an optimal setting for Super IO device.
Embedded Controller AEC-6967 Serial Port 2 Configuration Options Summary : Serial Port Enabled Default Disabled Enable or Disable Serial Port (COM) Change Settings Auto Default IO=2F8h; IRQ=3; IO=3F8h; IRQ=3,4; IO=2F8h; IRQ=3,4’ IO=3E8h; IRQ=3,4; IO=2E8h; IRQ=3,4; Select an optimal setting for Super IO device.
Embedded Controller AEC-6967 Serial Port 3 Configuration Options Summary : Serial Port Enabled Default Disabled Enable or Disable Serial Port (COM) Change Settings Auto Default IO=3E8h; IRQ=5; IO=2E8h; IRQ=5; IO=2D0h; IRQ=5’ IO=2D8h; IRQ=5; Select an optimal setting for Super IO device.
Embedded Controller AEC-6967 Serial Port 4 Configuration Options Summary : Serial Port Enabled Default Disabled Enable or Disable Serial Port (COM) Change Settings Auto Default IO=2E8h; IRQ=5; IO=3E8h; IRQ=5; IO=2D0h; IRQ=5; IO=2D8h; IRQ=5; Select an optimal setting for Super IO device.
Embedded Controller AEC-6967 Serial Port 5 Configuration Options Summary : Serial Port Enabled Default Disabled Enable or Disable Serial Port (COM) Change Settings Auto Default IO=2D0h; IRQ=5; IO=3E8h; IRQ=5; IO=2E8h; IRQ=5; IO=2D8h; IRQ=5; Select an optimal setting for Super IO device.
Embedded Controller AEC-6967 Serial Port 6 Configuration Options Summary : Serial Port Enabled Default Disabled Enable or Disable Serial Port (COM) Change Settings Auto Default IO=2D8h; IRQ=5 IO=3E8h; IRQ=5; IO=2E8h; IRQ=5; IO=2D0h; IRQ=5; Select an optimal setting for Super IO device.
Embedded Controller H/W Monitor Chapter 3 AMI BIOS Setup 3-28 AEC-6967
Embedded Controller AEC-6967 Setup submenu: Chipset Chapter 3 AMI BIOS Setup 3-29
Embedded Controller System Agent (SA) Configuration Options Summary : Graphics Configuration Config Graphics Settings.
Embedded Controller AEC-6967 Graphics Configuration Options Summary : Internal Graphics Auto Default Disabled Enabled Keep IGD enabled based on the setup options.
Embedded Controller AEC-6967 352M 384M 416M 448M 480M 512M Select DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the Internal Graphics Device. DVMT Total Gfx Men 128M 256M MAX Default Select DVMT5.0 Total Graphic Memory size used by the Internal Graphics Device.
Embedded Controller AEC-6967 Display Control Options Summary : Boot Display Select VBIOS Default Default CRT HDMI DVI Select the Video Device during POST and DOS. This has no effect if external graphics present.
Embedded Controller AEC-6967 PCH-IO Configuration Options Summary : Power Mode ATX Type Default AT Type Select power supply mode. Restore AC Power Power off Loss Power on Last State Default Select AC power state when power is re-applied after a power failure.
Embedded Controller AEC-6967 Control Detection of the Azalia device. Disabled = Azalia will be unconditionally disabled Enabled = Azalia will be unconditionally Enabled Auto = Azalia will be enabled if present, disabled otherwise. Azalia Internal HDMI Disabled Codec for Azalia Enabled Default Enable or disable internal HDMI codec for Azalia. Azalia HDMI codec Disabled Default Port B Enabled Enable or disable internal HDMI codec Port for Azalia.
Embedded Controller Chapter 3 AMI BIOS Setup 3-36 AEC-6967
Embedded Controller AEC-6967 Setup submenu: Boot Options Summary : Quiet Boot Disabled Enabled Default Enables or disables Quiet Boot option Launch I82579LM Disabled Default PXE OpROM Enabled Enable or Disable Legacy Boot Option for I82579LM.
Embedded Controller Hard Drives BBS Priorities Chapter 3 AMI BIOS Setup 3-38 AEC-6967
Embedded Controller AEC-6967 Submenu: Security Change User/Supervisor Password You can install a Supervisor password, and if you install a supervisor password, you can then install a user password. A user password does not provide access to many of the features in the Setup utility. If you highlight these items and press Enter, a dialog box appears which lets you enter a password. You can enter no more than six letters or numbers. Press Enter after you have typed in the password.
Embedded Controller Setup submenu: Exit Chapter 3 AMI BIOS Setup 3-40 AEC-6967
Embedded Controller AEC-6967 Chapter 4 Driver Installation .
Embedded Controller AEC-6967 The AEC-6967 comes with an AutoRun DVD-ROM that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver DVD, the driver DVD-title will auto start and show the installation guide. If not, please follow the sequence below to install the drivers.
Embedded Controller 4.1 AEC-6967 Installation: Insert the AEC-6967 DVD-ROM into the DVD-ROM drive. And install the drivers from Step 1 to Step 8 in order. Step 1 – Install Chipset Driver 1. Click on the STEP 1-CHIPSET folder and double click on the infinst_autol.exe file 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 2 – Install VGA Driver 1. Click on the STEP2-VGA folder and select the OS folder your system is 2.
Embedded Controller AEC-6967 dotNet Framwork folder. Step 3 –Install Audio Driver 1. Click on the STEP3-AUDIO folder and select the OS folder your system is 2. Double click on the .exe located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 4 –Install LAN Driver 1. Click on the STEP4-LAN folder and select the folder of intel_82579 or realtek_8111E based on the LAN chipset in your system. 2.
Embedded Controller AEC-6967 Step 6 – Install RAID & AHCI Driver Please refer to the Appendix C RAID & AHCI Settings Step 7 – Install TPM Driver 1. Click on the STEP7-TPM folder and double click on the Setup.exe file 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 8 –Install Serial Port Driver (Optional) For Windows® XP 32-bit, select the folder of WINXP_32 and double click on the patch.
Embedded Controller AEC-6967 2. Change User Account Control Settings to [Never notify] 3. Reboot and Administrator login.
Embedded Controller AEC-6967 4. To run patch.bat with [Run as administrator].
Embedded Controller AEC-6967 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
Embedded Controller AEC-6967 A.
Embedded Controller AEC-6967 ********************************************************************************* *** // SuperIO relative definition (Please reference to Table 1) #define byte SIOIndex //This parameter is represented from Note1 #define byte SIOData //This parameter is represented from Note2 #define void IOWriteByte(byte IOPort, byte Value); #define byte IOReadByte(byte IOPort); // Watch Dog relative definition (Please reference to Table 2) #define byte TimerLDN //This parameter is represented
Embedded Controller AEC-6967 #define byte WDTRstBit // This parameter is represented from Note22 #define byte WDTRstVal // This parameter is represented from Note23 ********************************************************************************* *** ********************************************************************************* *** VOID Main(){ // Procedure : AaeonWDTConfig // (byte)Timer : Time of WDT timer.(0x00~0xFF) // (boolean)Unit : Select time unit(0: second, 1: minute).
Embedded Controller AEC-6967 VOID WDTEnableDisable(byte LDN, byte Register, byte BitNum, byte Value){ SIOBitSet(LDN, Register, BitNum, Value); } VOID WDTParameterSetting(){ // Watchdog Timer counter setting SIOByteSet(TimerLDN, TimerReg, TimerVal); // WDT counting unit setting SIOBitSet(UnitLDN, UnitReg, UnitBit, UnitVal); // WDT output mode setting, level / pulse SIOBitSet(ModeLDN, ModeReg, ModeBit, ModeVal); // Watchdog timeout output via WDTRST# SIOBitSet(WDTRstLDN, WDTRstReg, WDTRstBit, WDTRstVal); }
Embedded Controller AEC-6967 VOID SIOBitSet(byte LDN, byte Register, byte BitNum, byte Value){ Byte TmpValue; SIOEnterMBPnPMode(); SIOSelectLDN(byte LDN); IOWriteByte(SIOIndex, Register); TmpValue = IOReadByte(SIOData); TmpValue &= ~(1 << BitNum); TmpValue |= (Value << BitNum); IOWriteByte(SIOData, TmpValue); SIOExitMBPnPMode(); } VOID SIOByteSet(byte LDN, byte Register, byte Value){ SIOEnterMBPnPMode(); SIOSelectLDN(LDN); IOWriteByte(SIOIndex, Register); IOWriteByte(SIOData, Value); SIOExitMBPnPMode(); }
Embedded Controller AEC-6967 Appendix B I/O Information Appendix B I/O Information B-1
Embedded Controller B.1 I/O Address Map B.
Embedded Controller AEC-6967 B.
Embedded Controller Appendix B I/O Information B-4 AEC-6967
Embedded Controller AEC-6967 B.
Embedded Controller AEC-6967 Appendix C RAID & AHCI Settings Appendix C RAID & AHCI Settings C-1
Embedded Controller AEC-6967 C.1 Setting RAID OS installation to setup RAID mode Step 1: Copy the files below from the Driver CD: STEP 6 RAID&AHCI\WINXP_32 to Disk. Step 2: Connect the USB Floppy (Disk with the RAID&AHCI files) to the board.
Embedded Controller AEC-6967 Step 3: The setting procedures “In BIOS Setup Menu”: Select Advanced -> SATA Configuration -> SATA Mode Selection -> RAID Step 4: Select Advanced -> Launch Storage OpROM -> Enabled Appendix C RAID & AHCI Settings C-3
Embedded Controller AEC-6967 Step 5: Select Boot -> Boot Option #1 -> DVD ROM Type Step 6: Select Save & Exit -> Save Changes and Exit Appendix C RAID & AHCI Settings C-4
Embedded Controller AEC-6967 Step 7: Press “Ctrl-I” to enter MAIN MENU Step 8: Select “1.
Embedded Controller AEC-6967 Step 9: Select RAID Level -> RAID0(Stripe) Step 10: Select “Create Volume” Appendix C RAID & AHCI Settings C-6
Embedded Controller AEC-6967 Step 11: Type “Y” for confirmation Step 12: Select “5.
Embedded Controller Step 13: Choose “Y” Step 14: Setup OS Appendix C RAID & AHCI Settings C-8 AEC-6967
Embedded Controller AEC-6967 Step 15: Press “F6” Step 16: Choose “S” Appendix C RAID & AHCI Settings C-9
Embedded Controller AEC-6967 Step 17: Select the “Intel® Mobile Express Chipset SATA RAID Controller” Step 18: Select “ENTER” after choosing the model number.
Embedded Controller AEC-6967 Step 19: Setup is loading files.
Embedded Controller AEC-6967 C.2 Setting AHCI OS Installation to Setup AHCI mode Step 1: Copy the files below from the Driver CD: STEP 6 RAID&AHCI\WINXP_32 to Disk. Step 2: Connect the USB Floppy Disk with the RAID&AHCI files to the board.
Embedded Controller AEC-6967 Step 3: To install “In BIOS Setup Menu”, select Advanced -> SATA Configuration -> SATA Mode Selection -> AHCI Step 4: Next, select Boot -> Boot Option #1 -> DVD ROM Type Appendix C RAID & AHCI Settings C-13
Embedded Controller AEC-6967 Step 5: To save, select Save & Exit -> Save Changes and Exit Step 6: Setup OS Appendix C RAID & AHCI Settings C-14
Embedded Controller AEC-6967 Step 7: Press “F6” Step 8: Choose “S” Appendix C RAID & AHCI Settings C-15
Embedded Controller AEC-6967 Step 9: Choose “Intel® Mobile Express Chipset SATA AHCI Controller Step 10: Select “ENTER” to choose the model number Appendix C RAID & AHCI Settings C-16
Embedded Controller AEC-6967 Step 11: Setup is loading files Appendix C RAID & AHCI Settings C-17
Embedded Controller AEC-6967 Appendix D Electrical Specifications for I/O Ports Appendix D Electrical Specifications for I/O Ports D-1
Embedded Controller AEC-6967 D.1 DIO Programming AEC-6967 utilizes FINTEK F81866 chipset as its Digital I/O controller. Below are the procedures to complete its configuration and the AAEON initial watchdog timer program is also attached based on which you can develop customized program to fit your application. There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode.
Embedded Controller AEC-6967 D.
Embedded Controller AEC-6967 D.
Embedded Controller AEC-6967 ************************************************************************************ // Digital Output control relative definition (Please reference to Table 3) #define byte DOutput5LDN // This parameter is represented from Note43 #define byte DOutput5Reg // This parameter is represented from Note44 #define byte DOutput5Bit // This parameter is represented from Note45 #define byte DOutput5Val // This parameter is represented from Note46 #define byte DOutput6LDN /
Embedded Controller AEC-6967 ************************************************************************************ VOID Main(){ Boolean PinStatus ; // Procedure : AaeonReadPinStatus // Input : // Example, Read Digital I/O Pin 3 status // Output : // InputStatus : // 0: Digital I/O Pin level is low // 1: Digital I/O Pin level is High PinStatus = AaeonReadPinStatus(DInput3LDN, DInput3Reg, DInput3Bit); // Procedure : AaeonSetOutputLevel // Input : // Example, Set Digital I/O Pin 6 level AaeonSetOut
Embedded Controller AEC-6967 ************************************************************************************ Boolean AaeonReadPinStatus(byte LDN, byte Register, byte BitNum){ Boolean PinStatus ; PinStatus = SIOBitRead(LDN, Register, BitNum); Return PinStatus ; } VOID AaeonSetOutputLevel(byte LDN, byte Register, byte BitNum, byte Value){ ConfigToOutputMode(LDN, Register, BitNum); SIOBitSet(LDN, Register, BitNum, Value); } ****************************************************************************
Embedded Controller AEC-6967 ************************************************************************************ VOID SIOEnterMBPnPMode(){ IOWriteByte(SIOIndex, 0x87); IOWriteByte(SIOIndex, 0x87); } VOID SIOExitMBPnPMode(){ IOWriteByte(SIOIndex, 0xAA); } VOID SIOSelectLDN(byte LDN){ IOWriteByte(SIOIndex, 0x07); // SIO LDN Register Offset = 0x07 IOWriteByte(SIOData, LDN); } VOID SIOBitSet(byte LDN, byte Register, byte BitNum, byte Value){ Byte TmpValue; SIOEnterMBPnPMode(); SIOSelectLDN(byte LDN);
Embedded Controller AEC-6967 ************************************************************************************ Boolean SIOBitRead(byte LDN, byte Register, byte BitNum){ Byte TmpValue; SIOEnterMBPnPMode(); SIOSelectLDN(LDN); IOWriteByte(SIOIndex, Register); TmpValue = IOReadByte(SIOData); TmpValue &= (1 << BitNum); SIOExitMBPnPMode(); If(TmpValue == 0) Return 0; Return 1; } VOID ConfigToOutputMode(byte LDN, byte Register, byte BitNum){ Byte TmpValue, OutputEnableReg; OutputEnableReg = Register‐1; SIO
