Embedded Controller AEV-6312 AEV-6312 Compact Embedded Controller Intel® Atom™ D510 1.66GHz Processor Dual LAN, 4 USB2.0, 2 COM 2 PCI-Express Mini Card AEV-6312 Manual 1st Ed.
Embedded Controller AEV-6312 Copyright Notice This document is copyrighted, 2011. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Embedded Controller AEV-6312 Acknowledgments All other products’ name or trademarks are properties of their respective owners. AMI is a trademark of American Megatrends Inc. CompactFlash™ is a trademark of the Compact Flash Association. Microsoft Windows is a registered trademark of Microsoft Corp. Intel®, Atom™ are trademarks of Intel Corporation. PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation.
Embedded Controller AEV-6312 Packing List Before you begin operating your PC, please make sure that the following materials are enclosed: 1 AEV-6312 Embedded Controller 2 Wallmount Brackets 1 Screw Package 1 3-Pin Phoenix Connector 1 CD-ROM for manual (in PDF format) and drivers If any of these items should be missing or damaged, please contact your distributor or sales representative immediately. Note: 3.5 G module is an optional accessory.
Embedded Controller AEV-6312 Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a firm surface during installation.
Embedded Controller AEV-6312 d. The equipment does not work well, or you cannot get it to work according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20°C (-4°F) OR ABOVE 70°C (158°F). IT MAY DAMAGE THE EQUIPMENT. 16. The VCC operating power supply has to connect to the ACC port to power up the system.
Embedded Controller AEV-6312 ENERGY STAR This Product has been certified by ENERGY STAR® The Regulation of ENERGY STAR®: ENERGY STAR® Requirements for Computer Version 5.2. The Test Standard of ENERGY STAR®: IEC/EN 62301, ENERGY STAR® Program Requirements for Computer Version ENERGY STAR® Compliance: Power Management features (Basic) Using power-saving states The system provides the two power-saving states: Sleep and Hibernation. When Sleep is initiated, the power lights blink and the screen clears.
Embedded Controller AEV-6312 Initiating and exiting Sleep The system set the Sleep mode after 30 minutes of inactivity when running on external power. You can change to none Sleep mode if the system needs to be active at all time. The default power management settings have been selected for compliance with ENERGY STAR®, and are recommended by the ENERGY STAR® program for optimal energy savings.
Embedded Controller AEV-6312 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Boxer/ Industrial System 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 硬盘 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 外壳 中央处理器 与内存 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注： 一、此产品所标示之环保使用期限，系指在一般正常使用状况下。 二、上述
Embedded Controller Chapter 1 AEV-6312 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Hardware Installation 2.1 Dimension and I/O of AEV-6312 ............................... 2-2 2.2 Connectors and Jumpers of the Main Board ............ 2-4 2.3 List of Jumpers .......
Embedded Controller AEV-6312 Chapter 1 General Information Chapter 1 General Information 1- 1
Embedded Controller AEV-6312 1.1 Introduction AAEON introduces a new product line: In-vehicle Embedded Controller Solutions. The newest Boxer series AEV-6312 utilizes Intel® Atom™ processor and is designed for public transportation system that demands for anti-vibration and anti-shock protection. Moreover, this model features 200-pin DDR2 SODIMM up to 2 GB. For the storages, the AEV-6312 equips one SATA 1.5 Gb/s HDD bay and one Type II CompactFlash™ slot.
Embedded Controller AEV-6312 1.
Embedded Controller AEV-6312 1.3 Specifications Intel® AtomTM D510 1.66 GHz CPU Processor Chipset Intel® ICH8M System Memory 200-pin DDR2 SODIMM x 1, Max. 2GB Display DB-15 x 1, shared system memory up VGA Interface Storage Device Network Front I/O to 384MB/DVMT 4.0 SSD Type 2 CompactFlash™ Slot x 1 HDD SATA 1.
Embedded Controller AEV-6312 System Cooling Passive cooling Mounting Wallmount Operating Temperature -4oF ~ 122oF (-20oC ~ 50oC) (No Airflow, SSD) -4oF ~ 140oF (-20oC ~ 60oC) (Airflow, SSD) Storage Temperature -4oF ~ 158oF (-20oC ~ 70oC) Anti-Vibration Meets MIL-STD-810F-514.5C-1 Anti-Shock 50 G peak acceleration (11 msec. duration) - SSD Certification EMC Dimension (Wx H x D) CE/FCC Class B 8.39”(W) x 7.68”(H) x 2.2”(D) (213 mm x 195 mm x 56 mm) Gross Weight 6.
Embedded Controller AEV-6312 Chapter 2 Hardware Installation Chapter 2 Hardware Installation 2-1
Embedded Controller AEV-6312 2.
Embedded Controller AEV-6312 I/O USB LAN1 LAN2 COM1 VGA ACC V- V+ DC 12V / 24V SYS HDD Line out PWR GPS COM2 USB Chapter 2 Hardware Installation 2 - 3
Embedded Controller AEV-6312 2.
Embedded Controller AEV-6312 Solder Side Chapter 2 Hardware Installation 2 - 5
Embedded Controller AEV-6312 2.3 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
Embedded Controller AEV-6312 2.4 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
Embedded Controller AEV-6312 CN19 USB Port #4 CN20 USB Port #3 CN21 COM Port #3 CN22 COM Port #2 CN23 Audio Line-In/Out and MIC Connector CN24 RJ-45 Ethernet #2 CN25 RJ-45 Ethernet #1 CN26 Digital I/O CN27 Parallel Port CN28 LVDS Inverter Control CN29 LVDS Output CN30 USB Port #1 and #2 CN31 PS/2 Keyboard & Mouse CN32 COM Port #1 CN33 Analog CRT Display CN34 SIM Card Socket CFD1 Compact Flash Disk PCIE1 Mini-Card Slot #1 DIMM1 DDR2 SODIMM Slot Chapter 2 Hardware Insta
Embedded Controller AEV-6312 2.
Embedded Controller AEV-6312 2.6 Hard Disk Drive Installation Step 1: Unfasten the four screws on the bottom lid and two screws on front and rear panel Step 2: Fasten the four HDD screws and cover with the four black dampers. Then, place the HDD to the holder and assembly the damper bracket.
Embedded Controller AEV-6312 Step 3: Connect the HDD cable Step 4: Fasten the four screws on the bottom lid and two screws on front and rear panel Chapter 2 Hardware Installation 2 - 11
Embedded Controller AEV-6312 2.
Embedded Controller AEV-6312 Step 3: Adhere the heat spreading pad onto the RAM Step 4: Close the bottom lid of AEV-6312 and faten the four screws of the bottom lid and two screws on the front and rear panel Chapter 2 Hardware Installation 2 - 13
Embedded Controller AEV-6312 2.
Embedded Controller AEV-6312 Step 2: Connect the antenna cable to the connector on WiFi Card Step 3: Get the protective screw cover out of the AEV-6312 chassis Chapter 2 Hardware Installation 2 - 15
Embedded Controller AEV-6312 Step 4: Insert and fasten the Screw of Antenna to the hole Chapter 2 Hardware Installation 2 - 16
Embedded Controller AEV-6312 2.9 Wallmount Kit Installation Get the brackets ready and fasten appropriate four screws on each bracket. After fastening the two brackets on the bottom lid of AEV-6312, the wallmount kit installation has been finished.
Embedded Controller AEV-6312 2.10 Power Management AEV-6312 has special vehicle Power Supply Unit (PSU) that can provide power management functions below for vehicle applications.
Embedded Controller AEV-6312 Setting DC input mode DC Input Mode Options Location J2 J2 PIN13 and pin14 Mode OPEN 12V Operating Voltage Start Voltage (Please refer to the note below) 9V~18V 11V +/- 0.2V SHORT 24V 18V~36V 22V +/- 0.4V Note: Usually, the voltage of car battery stays at 13.5V~15V (@ 12V Mode), or at 27V~30V (@ 24V Mode) while the car engine is running.
Embedded Controller AEV-6312 For +12V DC input, there is no jumper on the pin header of power For +24V DC input, there are jumpers on the pin header of the power Chapter 2 Hardware Installation 2 - 20
Embedded Controller AEV-6312 USetting ACC ON/OFF Delay Time Mode ACC ON/OFF Delay Minutes The function of “ACC ON Delay Time” means that the PSU will wait for 1~30 seconds (depends on the timing you set) to turn on the AEV-6312 by sending a signal to the motherboard’s ON/OFF switch.
Embedded Controller AEV-6312 The function of “ACC OFF Delay Time” means that the PSU will wait for 0~120 minutes (depends on the timing you set) to turn off the AEV-6312 by sending a signal to the motherboard’s ON/OFF switch. You are also able to shut down the AEV-6312 manually during the “ACC OFF Delay Time” since the power is still on during this time.
Embedded Controller AEV-6312 USetting the ACC ON/OFF Delay Time The inner PSU of AEV-6312 provides 8 different “ACC ON Delay Time” settings (1, 3, 5, 10, 15 20, 25, 30 seconds) and 8 different “ACC OFF Delay Time” settings (1, 3, 5, 10, 30, 60, 120, 0 minutes). If you set the “ACC ON Delay Time Setting” for “1 sec,” it means to power on the AEV-6312 in 1 second. If you set “ACC OFF Delay Time Setting” for “0 min,” it means to power off the AEV-6312 immediately.
Embedded Controller AEV-6312 3, 4 5 sec SHORT 1, 2 3, 4 10 sec SHORT 5, 6 15 sec SHORT 1, 2 5, 6 20 sec SHORT 3, 4 5, 6 25 sec SHORT 1, 2 3, 4 30 sec 5, 6 SHORT Chapter 2 Hardware Installation 2 - 24
Embedded Controller Function JP2 Location AEV-6312 PIN Set Time Number ACC OFF 7, 8 Delay Time 9, 10 setting 11, 12 1 min OPEN 7, 8 3 min SHORT 9, 10 5 min SHORT 7, 8 9, 10 10 min SHORT 11, 12 30 min SHORT Chapter 2 Hardware Installation 2 - 25
Embedded Controller AEV-6312 7, 8 11, 12 60 min SHORT 9, 10 11, 12 120 min SHORT 7, 8 9, 10 0 min 11, 12 SHORT Input Low Voltage Protection If the input voltage is lower than the “defined input low voltage (10.3V ~10.7V @ 12V mode, 20.6V~21.4V @ 24V mode)” after 60 seconds, the inner PSU will convey a signal to imitate to press the power button to turn off the computer. Conversely, the ACC ignition will restart the computer if the input voltage is over 12/24 volt.
Embedded Controller AEV-6312 Defined Low Voltage Time ACC ON 60s PS ON Button Computer OFF Input Low Voltage Protection working mode Input Very Low Voltage Protection If the input voltage is lower than the “defined input very low voltage (8.8V ~9.2V @ 12V mode, 17.6V~18.4V @ 24V mode),” the computer will be shut down immediately. Conversely, the ACC ignition will restart the computer if the input voltage is over 12/24 volt.
Embedded Controller AEV-6312 Defined Very Low Voltage Time ACC ON PSU Power Output Computer OFF Input Very Low Voltage Protection working mode Chapter 2 Hardware Installation 2 - 28
Embedded Controller AEV-6312 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
Embedded Controller 3.1 AEV-6312 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. System configuration verification These routines check the current system configuration against the values stored in the CMOS memory.
Embedded Controller 3.2 AEV-6312 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
Embedded Controller AEV-6312 Chapter 4 Driver Installation Chapter 4 Driver Installation 4 - 1
Embedded Controller AEV-6312 The AEV-6312 comes with a CD-ROM that contains all drivers and utilities that meet your needs.
Embedded Controller AEV-6312 4.1 Installation: Insert the AEV-6312 CD-ROM into the CD-ROM Drive. And install the drivers from Step 1 to Step 7 in order. Step 1 – Install Chipset Driver 1. Click on the STEP1-CHIPSET folder and select the OS folder your system is 2. Double click on the infinst_autol.exe located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 2 – Install VGA Driver 1.
Embedded Controller AEV-6312 Step 4 – Install LAN Driver 1. Click on the STEP4-LAN folder and select the OS folder your system is 2. Double click on the PROWin32.exe located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 5 – Install GPS Driver 1. Click on the STEP5-GPS folder and double click on PL2303_Prolific_GPS_AllInOne_1013.exe file 2. Follow the instructions that the window shows 3.
Embedded Controller AEV-6312 4.
Embedded Controller AEV-6312 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
Embedded Controller AEV-6312 A.1 Programming AEV-6312 utilizes W83627DHG-P chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application.
Embedded Controller AEV-6312 (3) Exit the W83627DHG config Mode. Undesired result may occur if the config Mode is not exited normally. (1) Enter the W83627DHG config Mode To enter the W83627DHG config Mode, two special I/O write operations are to be performed during Wait for Key state. To ensure the initial state of the key-check logic, it is necessary to perform two write operations to the Special Address port (2EH).
Embedded Controller = 010 AEV-6312 Power LED pin is driven low. = 011 Power LED pin outputs 2Hz pulse with 50% duty cycle. = 100 Power LED pin outputs 1Hz pulse with 50% duty cycle. = 101 Power LED pin outputs 4Hz pulse with 50% duty cycle. = 110 Power LED pin outputs 0.25Hz pulse with 50% duty cycle. =111 Power LED pin outputs 0.25Hz pulse with 50% duty cycle.. Bit 4 Bit 3 Bit 2 : WDTO# count mode is 1000 times faster. =0 Disable. =1 Enable. : select WDTO# count mode.
Embedded Controller AEV-6312 WatchDog Timer Register II (Index=F6h, Default=00h) Bit 7-0 = 0 x 00 Time-out Disable = 0 x 01 Time-out occurs after 1 second/minute = 0 x 02 Time-out occurs after 2 second/minutes = 0 x 03 Time-out occurs after 3 second/minutes ………………………………..
Embedded Controller =1 AEV-6312 Force Watchdog Timer time-out event: this bit is self-clearing Bit 4 Bit 3-0 : Watchdog Timer Status. R/W =1 Watchdog Timer time-out occurred =0 Watchdog Timer counting : These bits select IRQ resource for Watchdog. Setting of 2 selects SMI.
Embedded Controller AEV-6312 A.2 W83627DHG Watchdog Timer Initial Program Example: Setting 10 sec.
Embedded Controller AEV-6312 ;/////////////////////////////////////////////////////////////////////////////////////////////// Dec dx Mov al,0f5h ;CRF5 (PLED mode register) Out dx,al Inc dx In al,dx And al,not 08h ;Set second as counting unit Out dx,al ;/////////////////////////////////////////////////////////////////////////////////////////////// Dec dx Mov al,0f6h ; CRF6 Out dx,al Inc dx Mov al,10 ;Set timeout interval as 10 sec.
